Installed new bumper today
#27
MBWorld Fanatic!
Thread Starter
Join Date: Aug 2006
Location: SoCal, Irvine
Posts: 3,020
Likes: 0
Received 0 Likes
on
0 Posts
Stage 2 C7 A6, QX60
look around the in the Classifieds, you'll find a set sooner or later
good luck
#29
Senior Member
Join Date: Jun 2007
Location: Boston, MA
Posts: 264
Likes: 0
Received 0 Likes
on
0 Posts
2005 A4 1.8TQ
#34
MBWorld Fanatic!
Join Date: Jul 2006
Location: SF East Bay
Posts: 1,255
Likes: 0
Received 0 Likes
on
0 Posts
"Double Stuff" SOLD | Nor*Cals "Pesky Audi"
wish i didnt have a beast of a driveway to handle, i'da done that rieger front too. this from the GB?
looks hawt!
looks hawt!
#35
MBWorld Fanatic!
Thread Starter
Join Date: Aug 2006
Location: SoCal, Irvine
Posts: 3,020
Likes: 0
Received 0 Likes
on
0 Posts
Stage 2 C7 A6, QX60
this is the second one
i bought one from GB, ut was on my car for 11 days only and got ripped off on the highway
rlee, suspension is next on my list
Last edited by yeuchau; 07-23-2007 at 09:05 PM.
#37
MBWorld Fanatic!
Thread Starter
Join Date: Aug 2006
Location: SoCal, Irvine
Posts: 3,020
Likes: 0
Received 0 Likes
on
0 Posts
Stage 2 C7 A6, QX60
3.5 to 4 hrs, cause i didn't know I had to remove that hanger in step 8, so that waste me like 30 mins to 1 hr
cause I did everything on my own
cause I did everything on my own
#40
MBWorld Fanatic!
#42
Senior Member
Join Date: Jun 2005
Location: NYC
Posts: 468
Likes: 0
Received 0 Likes
on
0 Posts
BLACK 05 C230SS
8. now you can remove the bumper, try to pull the bumper cover out as evenly as possible. When removing the bumper cover, there's a clip at the front of the fender that will pop out when you do this, make sure you don't scratch the fender/bumper with that metal clip.
This is what it looks like after you remove the bumper, note that the 2 red circles, that's where you screw those 2 screws by the fog lights in step 4. You might have to change the hanger to the ones that comes with your new bumper, since they have different length.
Hi there,
I am planning on removing my bumper like yourself to replace my headlights. I'd like to know where this is located in STEP 8. You mention about a clip in the front somewhere that might scratch the fender/bumper and I want to know where this is located in your picture? I want to avoid the scratching and understand how to put the clip back when I put the bumper back.
Thanks!
This is what it looks like after you remove the bumper, note that the 2 red circles, that's where you screw those 2 screws by the fog lights in step 4. You might have to change the hanger to the ones that comes with your new bumper, since they have different length.
Hi there,
I am planning on removing my bumper like yourself to replace my headlights. I'd like to know where this is located in STEP 8. You mention about a clip in the front somewhere that might scratch the fender/bumper and I want to know where this is located in your picture? I want to avoid the scratching and understand how to put the clip back when I put the bumper back.
Thanks!
#43
MBWorld Fanatic!
Thread Starter
Join Date: Aug 2006
Location: SoCal, Irvine
Posts: 3,020
Likes: 0
Received 0 Likes
on
0 Posts
Stage 2 C7 A6, QX60
it's the clip is located where bumper and fender merges (on top of your side marker), if you pull the bumper, you will notice that
#46
Super Member
Join Date: Jan 2005
Location: Chula Vista, San Diego
Posts: 952
Likes: 0
Received 0 Likes
on
0 Posts
c230 Kompressor Coupe
#47
MBWorld Fanatic!
Join Date: Nov 2003
Location: Fresno, CA
Posts: 4,278
Likes: 0
Received 0 Likes
on
0 Posts
'09 A4 S Line
Behind the sidemarkers, but first make sure you push the impact strip toward the front of the car. It should slide at least 5mm or so, then needs a little bit of prying to come unclipped. I used a flathead screwdriver with a towel wrapped around the tip so it wouldn't scratch anything.
#48
MBWorld Fanatic!
Thread Starter
Join Date: Aug 2006
Location: SoCal, Irvine
Posts: 3,020
Likes: 0
Received 0 Likes
on
0 Posts
Stage 2 C7 A6, QX60
Behind the sidemarkers, but first make sure you push the impact strip toward the front of the car. It should slide at least 5mm or so, then needs a little bit of prying to come unclipped. I used a flathead screwdriver with a towel wrapped around the tip so it wouldn't scratch anything.
#50
Super Member
Join Date: Jan 2005
Location: Chula Vista, San Diego
Posts: 952
Likes: 0
Received 0 Likes
on
0 Posts
c230 Kompressor Coupe
Behind the sidemarkers, but first make sure you push the impact strip toward the front of the car. It should slide at least 5mm or so, then needs a little bit of prying to come unclipped. I used a flathead screwdriver with a towel wrapped around the tip so it wouldn't scratch anything.
Hmm I'm still a little confused... but I guess I'll see what you're talking about when I replace my bumper.