Tune out marker lights (ROW setting with STAR/SDS)
#1
Super Member
Thread Starter
Tune out marker lights (ROW setting with STAR/SDS)
Hey all,
Wondering if I can tune out the orange marker lights on the front bumper? I have STAR with developer mode but cant figure it out. I did it on my W211 by changing the CGW setting to ROW (rest of world).
Any ideas/suggestions for the W209? Its a 2005 CLK320 convertible.
Thanks!
Wondering if I can tune out the orange marker lights on the front bumper? I have STAR with developer mode but cant figure it out. I did it on my W211 by changing the CGW setting to ROW (rest of world).
Any ideas/suggestions for the W209? Its a 2005 CLK320 convertible.
Thanks!
#2
MBworld Guru
I am pretty sure you can disable it with SDS by using the development mode for the front SAM. Of course it's all in German, so unless you are fluent, then Google translate is your friend. What I did was install CutePDF and then printout to PDF, open the doc, cut and paste into Google Translate.
#3
Super Member
Thread Starter
I am pretty sure you can disable it with SDS by using the development mode for the front SAM. Of course it's all in German, so unless you are fluent, then Google translate is your friend. What I did was install CutePDF and then printout to PDF, open the doc, cut and paste into Google Translate.
#4
MBworld Guru
I've never tried on mine. Looking at SDS, there are many things that can be overridden in development mode. I know a guy who disabled his fog lights after installing a body kit that did not use them.
#5
Super Member
Thread Starter
#6
MBworld Guru
He owns a local indy shop here. I can't remember if he cancelled fogs on his CLK or CL. Next time I see him - and I will by the end of the years as I'm going to get him to do a road-force balance and alignment, I'll ask. But I think if you'll just translate the German pages in the Development mode, you'll find it.
#7
MBWorld Fanatic!
Please excuse my ignorance, but why not just change the lamp and/or cover? or just remove the lamp (I don't think they trigger an error)....?
Trending Topics
#8
Super Member
Thread Starter
Rudeney,
i tried but didn't get anywhere... i didnt find anything relating to exterior lighting that would possibly allow to activate/deactivate circuits.
Fatz,
it causes an error when the bulb is out. I have it ON due to bad wiring somewhere but i cant figure where. Been fighting this for months and it dawned on me that i turned them off on my E55 as i didnt like the way they looked.
i tried but didn't get anywhere... i didnt find anything relating to exterior lighting that would possibly allow to activate/deactivate circuits.
Fatz,
it causes an error when the bulb is out. I have it ON due to bad wiring somewhere but i cant figure where. Been fighting this for months and it dawned on me that i turned them off on my E55 as i didnt like the way they looked.
Last edited by V-AMG; 11-28-2016 at 04:04 PM.
#10
Super Member
Thread Starter
Just for my own knowledge, do you know what size resistors we'd need to trick the lights on MB?
Thanks!
#11
MBworld Guru
So you are saying the driver's side stays on and won't go out, even shutting the lights off? That's probably not wiring - it's probably a bad SAM. It can also be cause by voltage issues. A couple of times when I've had a bad battery, I had odd lighting issues like that.
As for SDS, I found a bunch of lighting settings in Dev mode, but I think they relate to the "standing lights" - the section is "STL".
As for SDS, I found a bunch of lighting settings in Dev mode, but I think they relate to the "standing lights" - the section is "STL".
#12
Super Member
Thread Starter
So you are saying the driver's side stays on and won't go out, even shutting the lights off? That's probably not wiring - it's probably a bad SAM. It can also be cause by voltage issues. A couple of times when I've had a bad battery, I had odd lighting issues like that.
As for SDS, I found a bunch of lighting settings in Dev mode, but I think they relate to the "standing lights" - the section is "STL".
As for SDS, I found a bunch of lighting settings in Dev mode, but I think they relate to the "standing lights" - the section is "STL".
How'd you get to STL? Control units>body>STL?
#13
MBworld Guru
Oh, I thought you meant the marker was on constantly and that's why you were trying to turn it off. In that case, maybe it is wiring. Front end collisions that dmamage the bumper often rip up the side marker wiring.
As for SDS, the STL settings are in the Developer section of the front SAM (under "Body").
As for SDS, the STL settings are in the Developer section of the front SAM (under "Body").