Hard track use upgrades
#226
#228
Yes please. Rear ducts available yet and is the bump steer mod required with the front ducts. Any discount available for poor Brits? :P
#229
So... They will have rear's in 2 weeks. Bumpsteer is not required for front ducts. They don't like Brits, so no discount...
The following 2 users liked this post by MegaLoL:
MG1422 (07-11-2019),
Pete De La Mare (07-11-2019)
#230
Haha now that’s just racist
I can wait two weeks though, hopefully they cost less than the fronts.
I can wait two weeks though, hopefully they cost less than the fronts.
The following users liked this post:
MegaLoL (07-14-2019)
#231
Just drive with TC completely off and you wont need the rear ducts lol
#232
Traction was always off on my E92 M3 track car, this is slightly different lol.
#233
After a nice chat with Lukas of Renntech Germany, I'm going with their front and rear ducts. There is sufficient difference in the designs and cooling effect that make me lean towards this solution over the TIKT alternative. No doubt the TIKT ones work way better than no ducts, but I believe there to be added performance with the Renntech ones.
#234
After a nice chat with Lukas of Renntech Germany, I'm going with their front and rear ducts. There is sufficient difference in the designs and cooling effect that make me lean towards this solution over the TIKT alternative. No doubt the TIKT ones work way better than no ducts, but I believe there to be added performance with the Renntech ones.
The following users liked this post:
Pete De La Mare (07-16-2019)
#235
MBWorld Fanatic!
Join Date: May 2008
Location: Overland Park, KS
Posts: 2,440
Received 950 Likes
on
571 Posts
‘24 BMW iX M60
After a nice chat with Lukas of Renntech Germany, I'm going with their front and rear ducts. There is sufficient difference in the designs and cooling effect that make me lean towards this solution over the TIKT alternative. No doubt the TIKT ones work way better than no ducts, but I believe there to be added performance with the Renntech ones.
Can you elaborate on why RT believes their’s to be the better solution?
PM if necessary.
Bish
#236
Bish, details such as both caliper cooling, better centre-disc cooling, and retaining a heat shield near the lower wishbone bearing. They didn’t want to give away specific details or low-level photographs as the current product is the result of 4 years of development with MB themselves.
Last edited by Pete De La Mare; 10-16-2019 at 03:32 PM.
The following users liked this post:
thebishman (07-17-2019)
#237
Member
#238
MBWorld Fanatic!
Join Date: May 2008
Location: Overland Park, KS
Posts: 2,440
Received 950 Likes
on
571 Posts
‘24 BMW iX M60
I was just about to post that ‘Vengence Racing’ has now become the official US distributor for Tikt products in the USA. I’ve sent them an email asking about pricing on the brake ducts; (hopefully front and rear), and will post back when I hear something.
Just in case someone remains interested.
Bish
#239
No doubt the TIKT stuff works, the data and evidence is plain to see. It would be good to compare the two somehow.
Last edited by Pete De La Mare; 07-17-2019 at 12:12 PM.
#240
I think both the Tikt and the Renntech would have similar performance. The cooling "mouth" does look larger on the tikt than the renntech but I only say this from pictures. I think it will come down to what each one is comfortable with brand a cost wise. The renntech might also be better looking carbon fiber but I really dont care because you cant see them.
Going out to COTA this Friday for a night event. I'm excited to test out the new alignment. I hope my tires have enough life for 2 days in the Texas heat.
Going out to COTA this Friday for a night event. I'm excited to test out the new alignment. I hope my tires have enough life for 2 days in the Texas heat.
Last edited by MG1422; 07-17-2019 at 12:57 PM.
The following 3 users liked this post by MG1422:
#241
Here's my design for the rear ducts. It works with cut dust shields to feed air to the rotor and the brake calipers. I'd be happy to make a few if I can get about 4 people interested at $250 a set.
#242
Ronac, nice job on the ducting! Get ready for all the questions... I’ll start. Have you tracked them yet? What material did you use, HDPE? Did you print them or create a mold? I may be very interested in a set.
#243
This set is printed but I'll be outsourcing it to have it thermoformed out of polypropylene with flame retardant additives (if enough people are interested).
I'll be testing these out in late August.
I'll be testing these out in late August.
#244
*sorry, read all that wrong......
Last edited by Pete De La Mare; 10-16-2019 at 03:30 PM.
The following 2 users liked this post by Pete De La Mare:
MG1422 (07-29-2019),
thebishman (07-29-2019)
#245
I use SRF everytime I am out at COTA. No problems so far.
The following users liked this post:
Pete De La Mare (07-29-2019)
The following users liked this post:
Pete De La Mare (07-29-2019)
#247
Pagid RSC1.
Last edited by Pete De La Mare; 10-16-2019 at 03:23 PM.
#248
MBWorld Fanatic!
Join Date: May 2008
Location: Overland Park, KS
Posts: 2,440
Received 950 Likes
on
571 Posts
‘24 BMW iX M60
Ordered mine the other day after hearing from Peter. The Pagid RSC1 pads are bloody difficult to find as there aren’t many around. Clark at Apex Motorsports found them for me with a good discount, so hit him up if you want to try a slightly more track oriented pad than the OEMs with your CCMs.
Bish
Bish
#249
Anyone got a good track geo they could share with me please? I’m not going to be able to get a Renntech setup before the Nordschleife track day.
Good news is that the ducts will be with me on Monday.
Good news is that the ducts will be with me on Monday.