Rear bumper impact strips.......
i have a 2002 c240... was planning to put on a 05-06 c230 amg rear bumper on my car... was wondering if the rear bumper impact strips on my car will work on the amg bumper.... or do i have to purchase new impact strips specifically for this bumper?
Thanks -Carino |
Originally Posted by CharlesCarino
i have a 2002 c240... was planning to put on a 05-06 c230 amg rear bumper on my car... was wondering if the rear bumper impact strips on my car will work on the amg bumper.... or do i have to purchase new impact strips specifically for this bumper?
Thanks -Carino No. you can use your the same impact strips. |
the rear strips im not sure...it SHOULD be the same, but def, the front pre-facelift and facelift ones, the strips are diff
|
the front and rear impact strip are the same for the AMg and NON-AMG u can reused your old ones unless u wanna get the Euro-Impact Strips
|
does anybody know how to remove the stip??
|
Originally Posted by chkoo
(Post 3667477)
does anybody know how to remove the stip??
Thanks, Jake |
Originally Posted by WaveyKat
(Post 1726355)
the front and rear impact strip are the same for the AMg and NON-AMG u can reused your old ones unless u wanna get the Euro-Impact Strips
|
Originally Posted by BF_JC230
(Post 3667491)
STF for my "OCD" DIY...it is not hard to do...use good tape, or even better - foam backed tape!
Thanks, Jake |
Originally Posted by chkoo
(Post 3668024)
cant seem to find it :\.. can u link me to the page pretty pretty please!!!
Originally Posted by BF_JC230
;Hi,
I hope this helps….Funny I read about European impact strips and lights this morning…I had an idea last night to; 1) Cast the chrome in a clear UV resistant resin – molding in “sockets” to receive 5 watts worth of LEDs for the running light and a few more LEDs for a better turn signal. 2) Chrome the back half of the cast clear part so that it looks chrome all over. 3) Wire in the LEDs to the running light wire and the other LEDs to the turn signal. 4) Re-Install Anyway…On to your issue… (This is what my Dad and I figured out in the drive way one day…) 1. TAPE off all the surrounds on the upper and lower rail to protect the finish. 2. Use two small / thin mechanics scales / or thin plastic tools / wedges to get in-between the impact strip and the fascia – you are looking for the THREE molded in snaps – release them by riding your tool over the top / bottom of the respective snap. 3. Start releasing the snaps on the INBOARD side first walking the strip out to the corner. 4. The corner has an upper and lower HOOK that you must roll out of its catch. 5. Remove impact strip to do what ever! Hope this helps, Jake https://mbworld.org/forums/attachmen...rip_step_1.jpg https://mbworld.org/forums/attachmen...rip_step_2.jpg https://mbworld.org/forums/attachmen...rip_step_3.jpg |
Originally Posted by c180 sonny
(Post 3667495)
whats the difference???
http://phuonger.247media.org/photos/...%20Blue/14.jpg |
karo is that franks car? color edited?
|
Originally Posted by paypaboi
(Post 3668043)
Here ya go!
https://mbworld.org/forums/attachmen...rip_step_1.jpg https://mbworld.org/forums/attachmen...rip_step_2.jpg https://mbworld.org/forums/attachmen...rip_step_3.jpg |
Originally Posted by mbcollector
(Post 3668586)
karo is that franks car? color edited?
|
Originally Posted by mbcollector
(Post 3668586)
karo is that franks car? color edited?
:rolf: |
my god! that blue carlsson c32 is beautiful!!!
|
All times are GMT -4. The time now is 12:37 PM. |
© 2024 MH Sub I, LLC dba Internet Brands