Originally Posted by Sparky18
(Post 7582675)
I was told my car already had the control unit for the illuminated star by the dealer. Than the quoted me 812 to supply and install. Part numbers were 166-817-75-00(star) and 205-820-44-00(wiring harness). They were unable to tell me what functions the star would have?. They told me I was lucky to have control module being that they want 400 for that. I have 2017 c300 sedan. Not sure if anyone else has info on how this setup functions on this vehicle? Fuse tap... Illuminated star... |
Thank you for the links and info!! |
I have a 2017 sedan C300 with a big piece of engine cover. Anyone have information or instruction how to remover it to expose the fusebox?
Thanks |
Hi there,
I own a Mercedes-Benz C300 2015 and I ordered the star from ebay and could not make it work. I followed the guide step by step on https://mbworld.org/how-tos/a/merced...ed-star-384223. do you think by fuse tapping it will work? can you advise? Thanks |
Originally Posted by jayband
(Post 6153626)
Provide a DIY guid for installing illuminated star in your W205. This guide is for car without the Driver Assistance Package (Distronic Plus) Code 997 option.
Let me know if you have any questions. https://cimg9.ibsrv.net/gimg/www.mbw...dd4d1c0a90.jpg LED illuminated star https://cimg0.ibsrv.net/gimg/www.mbw...6c1cbd7231.jpg wire harness assembly https://cimg3.ibsrv.net/gimg/www.mbw...071c02adf5.jpg Remove the star counter clockwise from the grill https://cimg4.ibsrv.net/gimg/www.mbw...c31e5d2b41.jpg https://cimg7.ibsrv.net/gimg/www.mbw...9fc72f211a.jpg Locate your engine fuse box in you driver side https://cimg8.ibsrv.net/gimg/www.mbw...81e3f676f7.jpg Remove the plastic cover and expose the fusebox https://cimg9.ibsrv.net/gimg/www.mbw...de953c4e66.jpg Use a Torx screwdriver and remove the 2 screws and remove the top cover. Use a pry tool to carefully pry back side of the fuse/relay module https://cimg0.ibsrv.net/gimg/www.mbw...20c96d0fcf.jpg Life up the edge of the fuse/relay module. There is sufficient wire underneath so you can pull the entire module out and set it aside. https://cimg1.ibsrv.net/gimg/www.mbw...33f181a8a2.jpg -Mark center of the top side edge and place another marker 1 inch down. Drill a 3/4" hole<br/><br/>-Route your red wire that comes with the kit through hole in grommet https://cimg2.ibsrv.net/gimg/www.mbw...30d99a968f.jpg In the back of the fuse/relay module, locate the S8 connector and connect the red wire to position 8 of the connector https://cimg3.ibsrv.net/gimg/www.mbw...0c53ca79ea.jpg Reinstall the fuse/relay module back to the box and install a 5A fuse into position F123 (B) https://cimg2.ibsrv.net/gimg/www.mbw...ed0fbef574.jpg Remove plastic rivets (1) that secure the radiator support panel https://cimg3.ibsrv.net/gimg/www.mbw...9c3b07bb15.jpg Remove plastic rivets (2) https://cimg4.ibsrv.net/gimg/www.mbw...4de2972039.jpg Remove plastic rivets (3) https://cimg9.ibsrv.net/gimg/www.mbw...4e274719e6.jpg -Route the cable towards to the center of the radiator<br/><br/>-Route the ground cable towards to the passenger side https://cimg4.ibsrv.net/gimg/www.mbw...ff0a141400.jpg Connect ground wire to ground terminal (passenger side) https://cimg5.ibsrv.net/gimg/www.mbw...172cffb3d9.jpg Connect the star wiring harness Reassemble in reverse order. |
So here is a picture of the instructions that came with my after market LED star that I bought from eBay. Can anyone help me identify where does the positive wire and negative wire connect to and where does the black line/signal wire connect to? The picture is not clear and very telling in the diagram.
My thought is that the positive electrode connects to the positive end of the battery and the negative to the negative end of the battery and then the signal wire taps into the fuse 108 or 110 for the headlights so that the star comes on only when the headlights are on and not as DRL's, but again this is just my inference and conclusion from this diagram. Any good electrical engineers out there who can help out, would be highly appreciated :) https://cimg0.ibsrv.net/gimg/www.mbw...0e09ad2dbb.jpg |
Originally Posted by Krypton
(Post 7603982)
So here is a picture of the instructions that came with my after market LED star that I bought from eBay. Can anyone help me identify where does the positive wire and negative wire connect to and where does the black line/signal wire connect to? The picture is not clear and very telling in the diagram.
My thought is that the positive electrode connects to the positive end of the battery and the negative to the negative end of the battery and then the signal wire taps into the fuse 108 or 110 for the headlights so that the star comes on only when the headlights are on and not as DRL's, but again this is just my inference and conclusion from this diagram. Any good electrical engineers out there who can help out, would be highly appreciated :) https://cimg0.ibsrv.net/gimg/www.mbw...0e09ad2dbb.jpg + Electrode = goes to battery + positive - Electrode = goes to battery - negative OR any properly grounded screw in engine bay. ACC = tap a fuse that only has power when the cars accessories have power OR when the engine is running. Your choice. (this is only to switch your star on/off) You may need this. As a test (before installing) you could connect the - and + wires to the battery, and then touch the ACC wire to + positive battery terminal to see if star turns on/off. https://www.blackboxmycar.com/pages/...ire-a-dash-cam Disclaimer (I am making these assumptions based on the information you provided) YOU COULD ALSO ASK THE SELLER TO BE SURE. :D |
Thanks brother for the info. I did assume this but I wanted to also know how to make the star come on with the headlights at night on auto or when I turn them on manually. I assume that to do that, I just connect the acc wire to the headlight fuse instead of the accessory or ignition fuse, correct? Yes i have already ordered the fuse tap a few days back.
Also, i think the main battery on a 2015 c300 is in the rear i think and only the aux battery is in the front so is it ok to connect it to the front battery? Just waiting for someone to confirm that I am in the right direction and I will go to town with this diy. The seller, unfortunately retains from giving any instructions 😔 |
Mercedes C Class W205
https://cimg1.ibsrv.net/gimg/www.mbw...2194cc97ef.jpg
Worked perfectly on my C Class. Just follow the instructions and you're all set. |
Originally Posted by Etienne Attard
(Post 7670474)
https://cimg1.ibsrv.net/gimg/www.mbw...2194cc97ef.jpg
Worked perfectly on my C Class. Just follow the instructions and you're all set. |
Originally Posted by benzdude
(Post 7670478)
is that your garage or a shipping container? :D :rolf:
|
Originally Posted by Etienne Attard
https://cimg1.ibsrv.net/gimg/www.mbw...2194cc97ef.jpg
Worked perfectly on my C Class. Just follow the instructions and you're all set. |
Originally Posted by benzdude
it appears this setup is similar to a dash camera hard wire install.
+ Electrode = goes to battery + positive - Electrode = goes to battery - negative OR any properly grounded screw in engine bay. ACC = tap a fuse that only has power when the cars accessories have power OR when the engine is running. Your choice. (this is only to switch your star on/off) You may need this. As a test (before installing) you could connect the - and + wires to the battery, and then touch the ACC wire to + positive battery terminal to see if star turns on/off. https://www.blackboxmycar.com/pages/...ire-a-dash-cam Disclaimer (I am making these assumptions based on the information you provided) YOU COULD ALSO ASK THE SELLER TO BE SURE. :D |
Im not sure if this is a similar setup. But here is a tutorial. |
Originally Posted by suby01
Im not sure if this is a similar setup. But here is a tutorial. |
2 Attachment(s)
Finally got around to installing the Star after having it sit in my garage for 1 year and contemplating if I can do it without any instructions provided or should i get a shop to do it for $100 or so. Glad i used some common logic and some help from a member on the forum and i was able to do it in 15 minutes!
|
Great post , very helpful.
Originally Posted by jayband
(Post 6153626)
Provide a DIY guid for installing illuminated star in your W205. This guide is for car without the Driver Assistance Package (Distronic Plus) Code 997 option.
Let me know if you have any questions. https://cimg9.ibsrv.net/gimg/www.mbw...dd4d1c0a90.jpg LED illuminated star https://cimg0.ibsrv.net/gimg/www.mbw...6c1cbd7231.jpg wire harness assembly https://cimg3.ibsrv.net/gimg/www.mbw...071c02adf5.jpg Remove the star counter clockwise from the grill https://cimg4.ibsrv.net/gimg/www.mbw...c31e5d2b41.jpg https://cimg7.ibsrv.net/gimg/www.mbw...9fc72f211a.jpg Locate your engine fuse box in you driver side https://cimg8.ibsrv.net/gimg/www.mbw...81e3f676f7.jpg Remove the plastic cover and expose the fusebox https://cimg9.ibsrv.net/gimg/www.mbw...de953c4e66.jpg Use a Torx screwdriver and remove the 2 screws and remove the top cover. Use a pry tool to carefully pry back side of the fuse/relay module https://cimg0.ibsrv.net/gimg/www.mbw...20c96d0fcf.jpg Life up the edge of the fuse/relay module. There is sufficient wire underneath so you can pull the entire module out and set it aside. https://cimg1.ibsrv.net/gimg/www.mbw...33f181a8a2.jpg -Mark center of the top side edge and place another marker 1 inch down. Drill a 3/4" hole<br/><br/>-Route your red wire that comes with the kit through hole in grommet https://cimg2.ibsrv.net/gimg/www.mbw...30d99a968f.jpg In the back of the fuse/relay module, locate the S8 connector and connect the red wire to position 8 of the connector https://cimg3.ibsrv.net/gimg/www.mbw...0c53ca79ea.jpg Reinstall the fuse/relay module back to the box and install a 5A fuse into position F123 (B) https://cimg2.ibsrv.net/gimg/www.mbw...ed0fbef574.jpg Remove plastic rivets (1) that secure the radiator support panel https://cimg3.ibsrv.net/gimg/www.mbw...9c3b07bb15.jpg Remove plastic rivets (2) https://cimg4.ibsrv.net/gimg/www.mbw...4de2972039.jpg Remove plastic rivets (3) https://cimg9.ibsrv.net/gimg/www.mbw...4e274719e6.jpg -Route the cable towards to the center of the radiator<br/><br/>-Route the ground cable towards to the passenger side https://cimg4.ibsrv.net/gimg/www.mbw...ff0a141400.jpg Connect ground wire to ground terminal (passenger side) https://cimg5.ibsrv.net/gimg/www.mbw...172cffb3d9.jpg Connect the star wiring harness Reassemble in reverse order. I have a query regarding how to connect the wire to pin 8 of the S8 connector. When I stick it in it keeps falling off. Thanks in advance ... |
So I had boughten my illuminating star from Amazon. It came only with Red and Black wire. I spliced the Red wire to the grey/yellow wire of the headlight on the driver's side and the black wire to the body of the car. I saw these instructions on a W205 post but it is not working for me... anyone have any ideas? https://mbworld.org/forums/c-class-w...iring-yet.html
|
question about 166817031664
hi there
is that include wire harness A 205 820 44 00 if i purchase A 166817031664 ? thank you. |
Originally Posted by Esandoval87
So I had boughten my illuminating star from Amazon. It came only with Red and Black wire. I spliced the Red wire to the grey/yellow wire of the headlight on the driver's side and the black wire to the body of the car. I saw these instructions on a W205 post but it is not working for me... anyone have any ideas? https://mbworld.org/forums/c-class-w...iring-yet.html
|
Hello i have glc 43 amg 2018
Hello! I have a glc benz mercedes 43 amg 2018. Where do I connect the 16-pin sheet of the luminous star?
https://cimg9.ibsrv.net/gimg/www.mbw...c5e53ed1e.jpeg |
Originally Posted by julimontaldo
(Post 8185165)
Hello! I have a glc benz mercedes 43 amg 2018. Where do I connect the 16-pin sheet of the luminous star?
https://cimg9.ibsrv.net/gimg/www.mbw...c5e53ed1e.jpeg Somenone knows if you have to do any coding or ir you can connect to ECU with Xentry? Thanks in advance. |
Originally Posted by vic viper
(Post 6153941)
Would be nicer if the star followed the DRL.s, this way it would lit up as soon as the car is unlocked in dark conditions.
|
3 Attachment(s)
Originally Posted by Andy74
(Post 7600196)
I don't see that your illuminated star package includes a control unit. Can you share a DIY for an illuminated star with a control unit. I understand that if my package has a control unit the star will go on only when i lock unclock the car and will turn off when i start the engine? https://cimg8.ibsrv.net/gimg/www.mbw...176c77ce1f.jpg
|
All times are GMT -4. The time now is 12:03 PM. |
© 2024 MH Sub I, LLC dba Internet Brands