Bulletins 212, 218, 207, 238, 257
 

DTB P-B-54.70/218 MAY09 Vehicles equipped with Blind Spot Assist (code 234) issuing an erroneous warning when driving along crash barriers or walls the radar sensor control unit (SGR) needs to be flashed.

S-B-54.30/222 MAY09 - 212.056/072 up to VIN A016686 analog needles in the IC are not functioning for approximately one or two minutes after engine start typically occurs in cold temperatures. The IC software will be updated.

Service Campaign 2009070001 JUL09 to properly re-calibrate daytime running lamp operation, a software calibration number (SCN) update must be installed.

LI68.50-P-047173 JUN09 roller blind motor does not start at extremely cold temperatures, dealer will perform SCN coding to rear SAM increasing current to 8A.

LI80.61-P-047297 JUL09 anti-theft alarm system (ATA) activation after keyless-go (KG) unlocking via a door handle, update software to KG control unit.

LI68.10-P-047474 JUL09 rattling/vibrating noises at center IC/speaker cover because of production tolerances, felt will be installed.

LI68.20-P-047911 SEPT09 - lid of the center 212 console does not open by itself, sticks and must be opened by hand the design of the rubber stops can cause the lid to stick contact surface of buffers will e covered with felt and sealing lip lubricated.

LI61.25-P-047933 SEPT09 - 212 up to VIN 024513 under floor paneling s loose or sags, modified retaining clips will be replaced.

LI54.30-P-047934 SEPT09 - 212 as of VIN A002401 up to A0132-8, 207 F000435 – F003845, high temperatures inside the vehicle may cause the analog clock to stop or permanently run slow instrument cluster will be replaced.

LI82.62-P-048033 SEPT09 - 207.3 with panoramic sunroof, due to incorrect installation of the door lining soundproofing may press against the front door speaker causing interference, soundproofing will be replaced

LI32.22-P-048108 OCT09 – rubbing/grazing noises from the front axle when driving, replace strut boot with modified protective boot.

LI82.35-P-048244 OCT09 – washer fluid indicator on IC shows reservoir is empty although reservoir contains sufficient fluid, inspect sensor refill with concentrate and tap water at the recommended mixing ratio. 2-pin sensor cannot close circuit under following conditions: use of distilled or de-ionized water, tap water content of mixing ratio is too low, proportion of winter fluid concentrate is too high.

LI54.18-P-048131 NOV09 – 212 up to VIN A039612 wiring harness damaged in area of roof frame possible complaints vehicle cannot start, Bluetooth nonfunctional, multifunction camera nonfunctional, and night view camera nonfunctional.

LI54.65-P-048393 NOV09 – Parktronic nonfunctional, update control unit software.

Thanks!
 

Thanks for the information, especially the TSB information.

LI42.10-P-048315 DEC09 rear brakes squeal, pad slots will be cleaned, pads + retaining springs replaced with guide pieces lubricated under warranty.

Service Campaign 2009110003 JAN10 VIN range A000977 to A092538 values of the backup battery (transmission selector lever) may be set too low this may lead to fault messages in the IC dealers will update the front SAM. Approximately 16,641 vehicles affected.

LI83.10-P-048662 JAN10 VIN range A057743 to A154303, water deflector below the windshield can become detached.

LI32.22-P-048597 JAN10 vehicle drops at rear axle after standing for a long time “Airmatic – Service Required” damaged sealing rings can lead to a microscopic leak, DAS leak & compressor test will be performed affected air spring will be replaced as required.

VIN question
 

The last eight of my VIN are AA126102. I noted that you reference VIN's with A and then numbers. Would mine come after the ones your last listed?
Thanks.

VIN range references apply to the last seven characters of your VIN. A126102 is higher than A057743 and below VIN cutoff A154303 therefore, bulletin 048662 applies to your vehicle if deflector below windshield is or becomes detached and protrudes in places.

TSB Sits?
 

[quote=konigstiger;3917691]
LI83.10-P-048662 JAN10 VIN range A057743 to A154303, water deflector below the windshield can become detached.

I e-mailed the service manager and he responded that if I had problem as described in the TSB, I could get it fixed. No problem that I am aware of. Will call him later, but got to wondering.
Your information is really appreciated, but is there a site where I can go to find the actual TSB? I checked out DOT, Edmunds and a couple of others, but they had no listings for 2010 E's.
Thanks.

PM email address and I can forward a copy or subscribe to STAR TekInfo ($18 for 24 hours) http://www.startekinfo.com/StarTek/subscribe.jsp to search all applicable recalls, service campaigns and DTBs inclusive of WIS access to print/download instruction sheets for repairs.

Need your help konigstiger
 

Hi konigstiger,

Your knowledge is very valuable for us. I need your help, I have a 2010 E350 4matic and I am having an awkward issue with the tranny, the tranny shifts smoothly except upshiftting from 4th to 5th gear, it has hiccup at low RPMs " between 1,500 and 2,500 RPMs, 25 to 35 MPH " it's kind drops the gear, and that when the adaptive shifting kicks in, it doesn't happen when the vehicle is cold or the transmission memory is reseted. However It doesn't happen while down-shifting either. I went to the dealer 3 times about this and they said "It's product characteristics and it's your driving style, you need to drive it more aggressively" is that true? I test drove a similar car for a family member and I am pretty sure that he doesn't drive that car aggressively and the tranny was very smooth. Is it normal behavior? If not, is there any service bulletin regarding this issue? what do you advise me to do?

There was thread that i have initiated about this earlier:
https://mbworld.org/forums/e-class-w...ease-help.html

Your help is greatly appreciated.

Check PM

I was at my local dealer and was told that there was a new update strictly for the coupes. something for the engine and tranny control unit. have you heard anything about it.

LI54.30-P-049068 MAR10 – 207 (coupe) up to VIN F014219 / 212 (sedan) to A079696 tachometer fluctuates by approximately 100 rpm, IC will be replaced.

LI54.21-P-049150 MAR10 – 207/212 LEDs seat heater, LEDs activate but heater remains inoperative rear SAM software requires flashing.

LI47.30-P-049162 MAR10 – 212 with engine 156/271/272/273 vehicle production 1/10/09 to 11/30/09 engine warning lamp associated with engine running characteristics, purge valve will be replaced.

C1A100301 MAR10 – 212 if you had additional (electronic gear selector) battery replaced dealer needs to check/replace ASAP due to poor/loose fit with terminal connector. N000000004039 is correct have dealer check VMI to see if your vehicle is included.

Hi.

Could i trouble you to post the full bulletin re :-

LI54.30-P-049068 MAR10

Thanks in advance

DO

Service Campaign 2010030007 APR10; underbody panels may be loose or sag, dealers will replace the left & right panel fasteners. Approximately 24,100 vehicles are affected.

Service Campaign 2010030010 APR10; values of the backup battery in the front SAM may be set too low leading to fault messages in the instrument cluster, dealers will update parameters. Approximately 16,616 vehicles are affected.

LI46.15-P-049680 JUN10 - 204/207/212 at low temperatures height adjustment of steering column occurs very slowly or may not be possible at all, replace motor with shaft.

Service Campaign 2010080001 AUG10 – MY10 212 incorrect front-axle floor jack pad installed, dealer will replace pad with part # 002998065005. Approximately 833 vehicles affected, check with dealer to see if VIN is included.

Recall 2010100002 OCT10 – loss of power steering fluid, dealer will check, re-torque connection fitting to line and exchange O-ring. Approximately 85,078 vehicles affected.

LI68.10-P-050507 OCT10 – debris in glove box, wipe out using damp microfiber cloth and vacuum.

LI83.00-P-050296 OCT10 – large AC temperature difference between left and right sides, update software.

LI82.85-P-050503 OCT10 – Audio/COMAND display may flicker after warm-up or operating 10-20 minutes and/or dark spots may be visible in daylight display, replace display.

LI82.60-P-050456 OCT10 – satellite radio channels, category names and lists missing some characters, replace receiver.

LI72.20-P-050272 OCT10 – lift gate occasionally does not open and rattling noise is heard, perform SCN coding in rear SAM.

LI82.85-P-050404 NOV10 – after headunit software update pressing NAVI button causes headunit to reboot, install DAS update.

LI32.30-P-050653 NOV10 – level control malfunction in MFD and system functions correctly without limitation, flash software with DAS 11/2010.

Recall 2010110001 NOV10 - MY2011 models 164, 164.8, 212, 251 diesel fuel filter may leak due to O-ring not properly lubricated, filter will be replaced. Approximately 2,302 vehicles affected.

Service Campaign 2010110005 DEC10 – Models 164, 164.8, 212, 251 MY09-01; over time, changes in resistance in the AdBlue tank heater lines may lead to fault entries. A detection of a fault in the heater lines may occur due to an overly sensitive data threshold condition. Dealers will update the software for the SCR Control Module and Engine Control Module to correct this condition. Approximately 12,519 vehicles affected have dealer check VMI to see if your vehicle is included.

Service Campaign 2010120001 JAN11 – 204.9, 207, 212 MY10-11 cylinder head may not have been produced to specification dealers will replace, approximately 15 vehicles affected:

WDC2049561F525043
WDC2049871F522009
WDC2049871F522462
WDD2074561F060116
WDD2074561F060142
WDD2074561F060752
WDD2120561A256194
WDD2120561A256504
WDD2120871A256239
WDD2120871A256441
WDD2120871A257525
WDD2120871A257786
WDD2120871A258023
WDD2120871A258137
WDD2122871A257078

is A1XXXXXX higher or lower than AAXXXXXX?

Thank you.

LI32.25-P-051123 FEB11 – 212 without Airmatic (489), 207 without vehicle dynamics (483) dull thumping noises or metallic rattling from the area of the front axle occurring @ speeds 10-45 mph, modified front struts should be installed.

LI42.10-P-051397 MAR11 – 212.077/277 without AMG ceramic brake system (B07) low mileage rear brake squeal, dealer should check batch # installed if within affected range 250-10; 264-10, 278-10; 288-10; 292-10; 307-10 pads are to be replaced.

Bulletin LI32.25-P-051123 FEB11
 

Is this a new Bulletin? My E350 has been at dealer since Tuesday AM - noise as described in the Bulletin plus an ongoing vibration (buzzing) issue in Steering Wheel. Called today to see what was going on, since I had not heard anything since dropping it off, and was advised he is waiting on parts - front strut(s). Asked why and was told, "...you heard a noise, so the tech thought we should do this." Not sure if doing just one or both - should they be done as a pair? If say they are just doing one, should I request the other one be done as well? Interesting timing; I just wish they could be up front about what is going on - I am happier knowing the truth and reason for an action, even if it isn't what one would hope for.

Also replacing a defective rear shock absorber PLUS just had a defective front shock replaced in February!!!

Is my vehicle a Zitrone?

Released 2/14/11

Replacing Front Struts
 

You are a wealth of valuable information adn all that visit this forum surely appreciate your knowledge and insight.

In the case of this bulletin, should both struts be replaced or is replacing one acceptable?

Both, check PM

Are there any details/specifics available on what the changes/modifications are on the new units?

Internal damping module of strut was modified, see “Cause” in bulletin copy I sent.

Thanks. LAST question (I hope): Should the vehicle have an alignment after the struts are replaced? Does replacement impact the alignment settings?

No, the only additional step would be to check headlamp adjustment.

LI80.61-P-049924 MAR11 – 204/207/212 Keyless-Go “key not recognized” unable to start engine, update KG control unit software.

LI54.30-P-050163 MAR11 – 207 without memory package (275), backrest not locked continues to be displayed after locked correctly, update IC software.

LI82.70-P-051455 MAR11 – 212 called party has difficulty understanding driver; voice inputs via VCS are misunderstood, update COMAND software.

LI91.10-P-049894 APR11 – 204/207/212 noise or play at seat adjuster, shim will be fitted.

Would it be possible to see the entire description of this issue?

Certainly, PM email address and I will send bulletin.

LI80.57-P-051521 – 207 no crank/start/intermittent no crank, if EIS is part # 2045455732 replace with 2045458132.

LI91.25-P-051700 – 212 as of VIN A344516 up to A387562 multicontour seat inoperative replace backrest padding (massage unit and actuator are permanently installed in padding).

LI91.25-P-051599 – 212 dynamic seat function or multicontour system inoperative replace air cushion on front seat backrest with improved part.

Hey Konigstiger, I used this DTB hoping it would give me the new Command upgrade that some here have gotten (with the Bluetooth streaming, fixed POI's-where it doesn't give you a random City location, better graphics, A/C display on the bottom of the screen, Nav Map graphics upgrade, etc.), and after them saying that they were uploading new software for 2 hours (which I know they did, because apparently it crashed right before it was complete the first time, and I had to leave the car overnight), I see absolutely no changes to my Command. Did I give them the wrong code for what I seeked?

Service Campaign 2011030004 MAY11 – MY11 212 dealer will check vibration damper and replace if necessary. If the first 3 digits on barcode are 167, replacement is necessary. Approximately 41 vehicles are affected.

LI72.12-P-051929 MAY11 – 212 wagon up to VIN A406843; cannot open rear door in low outside temperature, strip on the inner sealing lip can become drenched and then freeze onto roof frame, dealer should install modified left & right window guide rails.

LI32.22-P-052062 – 212 thumping from area of the front axle when driving over speed humps when the suspension strut rebounds, the rebound buffer spring causes a metallic knocking noise. Dealer should flash Airmatic control unit.

LI54.21-P-052072 – vehicles with 276/278 engines CEL in IC but engine does not display any problems (i.e.: fault code P060600) update ECU.

LI42.47-P-052197 - e63 VIN A415231-A421136 when attempting to switch on the Attention Assist function fault message appears, perform SCN coding of ESP control unit.

LI91.25-P-052529 SEPT11 dynamic seat inoperative shortly after restart flash multicontour seat control unit with new software.

LI03.10-P-052286 SEPT11 knocking noise from engine, inspect cylinder walls for scoring if found engine must be replaced. Affected vehicles are mostly production dates from 8/10 to 11/10 but might be outside this range situation was corrected as of engine # 2729xx 31932895 & 2739xx 30441186.

LI27.60-P-049981 OCT11 hard shifts, poor start characteristics, uncomfortable jolting – check oil level, check for software releases and check engine for unmetered air.

Engine Numbers
 

Where are the engine numbers located?
Thanks

Don't know where they're located *on the vehicle* but you can get it from the "datacard" available at startekinfo.You can sign up for free (for the first year IIRC) and once signed up you can get all sorts of interesting,useful,info about *your* vehicle (including your engine number) by entering your VIN number.

Service Campaign 2011100004 NOV11 – 2011 w212 Central Gateway (CGW) may not meet specifications dealer will update software. Approximately 2,575 vehicles affected have dealer check VMI to see if VIN is included.

Please take a listen and tell me your thoughts; YouTube link to my engine noise. One dealer told me normal but I beg to differ. Thanks. http://m.youtube.com/index?desktop_u...?v=6dkxZhr84ks

Check your email.

Recall 2011110002 – MY11 212 diesel fuel filter may develop leaks approximately 6,784 vehicles affected. Owners should receive a letter or have dealer check VMI to check if VIN is included.

LI46.20-P-049852 – 207 all, 212 except 4matic honking/squeaking noise when steering in both directions mainly occurs when warm. Radial shaft sealing ring to steering system will be replaced.

LI83.00-P-051420 – 212 up to VIN 1A411562 & 218 up to 1A004916 whistling or humming noise. If the noise disappears when opening a window, the problem is caused by the drain grommets of the sliding roof hose @ left & right rear.

LI88.20-P-052891 - 212 rear bumper sticks out in area of rear lamp. Bumper experiences thermal expansion mounting rails (fender area) cannot sufficiently hold the bumper in place. If bumper is not equipped with additional latch, it should be replaced. Note since JAN11 bumpers are equipped with additional retaining tab.

Oh crap! I have a 2011 E350 and on one side, the bumper protrudes (it has protruded since day 1 I bought the car). My car has a build date of 7/11. Does this mean it doesn't fall under this bulletin?

If this is what I'm thinking of, most new E's had it when I got my 2011, including mine to a slight extent. Mine is a 3/11 build date.

Regardless of JAN11 notation, I would have bumper checked.

Recall 2011110002 JAN12 – 2011 164, 164.8, 212 and 251 check diesel fuel filter replace if necessary. Due to the variations in the materials used by supplier filter may develop leaks. Approximately 6,784 vehicles affected.

LI67.30-P-050613 - 212 up to VIN A519818 front door windows intermittently reverse direction when closing cause excessive resistance dealer will replace and align window under warranty.

LI68.10-P-050415 - 212 burl walnut trim that is fading or discoloring and VIN is between A000988 to A291888 cause inadequate UV protection dealer will replace all trim under warranty.

Hi Konigstiger,

For:

LI68.10-P-050415 - 212 burl walnut trim that is fading or discoloring and VIN is between A000988 to A291888 cause inadequate UV protection dealer will replace all trim under warranty.

Is the issue and replacement limited to the serial range provided? I have an A31xxxx and the burl trim above the glove box is considerably faded as compared to the adjacent trim. Could there be a few outside the range with the issue?

Thanks in advance.

Regardless of VIN dealer should replace any discolored wood trim under factory warranty without question. You can reference DTB to justify a claim to replace all trim if you have concern that new piece may not match remaining trim.

What's your cars build date?

Picture of the faded Trim in my 2010. Emailed my dealer the pics this AM and asked him to get back to me with the date he wanted to schedule to replace all the trim - being replaced this Thursday.

Thanks for pics
 

Thanks for the pics. Finally understand exactly what it is.

WOW! That looks awful. Does your car sit in the sun a lot? Reason that I ask is because my car doesn't bake in the sun too often, and I have tinted windows which I wonder mask the effect of fading the wood. However, now that I see it, there's no doubt that my eyes aren't playing any tricks on me.... my cars wood has not faded at all, and it very colorful/full looking.

i don't understand why only faded on two sides, not the top :confused:?

LI46.20-P-053398 – Rattling/thumping noises from area of steering, possible cause excessive play between thrust piece and steering rack.

LI88.20-P-053415 – s212 (wagon) & 218 (CLS) Rear bumper sticks out in area of rear lamp, cause too much play between bracket for bumper and lamp. Thermal expansion causes the bumper to stick out, protective fill is installed to correct this.

LI82.10-P-053439 – “High Beam Assist nonfunctional” message, replace multi function camera and calibrate.

Generally had the slider pushed in. Dealer replaced all the wood. It was a factory defect; bad batch of UV protection.
Side note: given the many issues I have had with this vehicle, dealer and M-B replaced my 2010 with a new 2012! A HUGE show of unbelievable customer support that has endeared me to both forever. This is why M-B is #1 in customer retention. Forget the horror stories you read; work with them in a reasonable, professional manner and good things happen. The 2012 is sooooo sweet!!!

:y:y

http://www.allworldauto.com/tsbs/NHT...in_375901.html

I find when I accelerate, from stop the vechile gives a slight jerk. I'm not sure if it's my driving style though!

any idea of that service bulletin will affect me ; 2011 E250.

What does RM UPDATED mean?

LI27.60-P-051774 (original release 5/11), should be applicable - as I understand it dealer will update software.

Do you know what the trunk money is on a E 350 2012 and is there a Loyality program...I know there is a conquest of 3000.00 on 2012 e-class

OMG...my dealer told me that it's normal! :smash::smash::smash:

do you have a pic of that?

http://chandoan.smugmug.com/Other/11.../IMG0072-L.jpg

http://chandoan.smugmug.com/Other/11.../IMG0071-M.jpg

I believe this is the discoloration. I usually leave my tray tucked in, but you can see on the side it's starting to fade.

You guys with discoloration, do you leave your car out in the sun a lot? I don't, and I have my tray closed mostly, so it would be harder to tell if my car did have lack of UV protection on the wood. Though, I know for sure that there's been no fading yet (nice and dark/rich), in case I did keep the car for a long time, it would suck if the fading effects were slow enough to where the car would be out of warranty when I'd start to notice it.

Nope, mine was garaged at all times plus live in Cleveland and we have no sunshine! You can check if fading is occuring by opening your front door and compare the wood that is at the very front of the door and is tucked in next to the dashboard when the door is closed. There was a very noticeable difference on mine. Will post a picture when not on my phone.

Yeh. My car sits in the sun from 10am until 10 at night. Pretty much 6 days a week.

Ah, good one! I will keep an eye on that area as a gauge. Also, my windows are dark tinted which also would prevent the fading effect of UV rays in the case that my cars wood is one of the affected batches.

I own a 2010 E350 coupe, can you please send me the DTB so I can show them as they are giving me pushback about faded wood trim

thanks for the pic but i'm sorry, where is this part exactly :confused:? do you have a more zoom out pic? thanks in advance.

you see where it pops out? where the rear lamp and bump part meet? it doesn't look flushed in.

yes, i can see it pops out a bit but just not sure where is it exactly. is it your left tail light? the light from your pic looks more vertical than horizontal and it looks more like the tail light from a cadillac srx suv. that's why i'm kind of confused.

Yosheego, your wood console looks good to me. In fact, all the cars I saw at the dealer lot last had the same color and the sides were a little lighter on all the E sedans I saw; My dealer told me the expansion was normal too!

09/10 build as MY2011. The fading for me seems to be limited to the trim piece above the glove box, and not even across as it is more faded towards the AC vent on the right than on the left.

My car is garaged at home, but is parked outside in my spot at work, with a mixture of sun and shade. Of course, when I golf, it is outside in the sun for 5 hours or so at a time, as is the case when normally out and about.

LI88.30-P-053562 APR12 – wheel well liners in engine compartment heavily soiled. Vehicle with air and steel suspension have the same size liner opening the diameter of the steel spring is smaller allowing more dirt to enter. Dirt repellent foam will be fitted.

LI72.10-P-053587 APR12 – 212 as of VIN A444532 up to A487761 rattling noise from front door lock (left & right), insulate door module.

LI91.40-P-053536 APR12 – 212 & 218 (CLS) production 9/11 up to 1/12, right or left front seat belt does not roll up completely - reposition tensioning retractor and torque mounting bolts.

LI46.35-P-053719 MAY12 – 218 only “Power Steering Malfunction, Service Required” fault message on engine start, perform software update.

Subscribed. Konigstiger, you are the man!

LI20.40-P-053718 MAY12– 203, 164, 251, 204, 207, 212, 219, 216, 221 and 218 radiator fan starts although ignition has been off for longer than 30 minutes and/or fan changes to limp mode (runs @ 100%) while driving with display “cooling system” in instrument cluster and/or battery discharged, replace radiator fan. Only Brose/Temic fan, following part #s are affected 2215000993, 2215001093, 2215001193; 1645000493, 16450005693; 2035001693, 2035001494; 2045000293, 2045000493.

Model Years?
 

Thanks for keeping up informed, but what model years are involved in this?

MY not specified, your vehicle (VIN) is equipped with 2045000293 - check your email.

Thank You!
 

Thanks once again for your service.:zoom:

LI88.50-P-053768 JUN12 – 207, 212 and 204 without AMG package, edges of the rear spoiler accessory protrudes at sides - incorrect installation, spoiler will be replaced (re-gluing is not permissible).

LI82.85-P-053927 JUN12 – COMAND display “Metadata loss – Please reimport all media data”, update COMAND software (Telematics CD 05/2012).

Subscribe
 

Your posts are very helpful. Just bought E350 VIN A643834.
You appear to be able to track bulletins applying to specific cars.
What is the best way to track your info?? I assume regular readings.
Ted

Subscribed

LI54.10-P-054089 JUL12 – 204, 207 and 212 battery discharged vehicle does not start, rotary light switch sending wrong signal after ignition off (i.e.: power consumption by low beams) switch will be replaced.

LI82.85-P-053600 AUG12– 212, 207, 218 COMAND unit starts up then switches itself off after a short time when CDs/DVDs are loaded. Update COMAND software.

LI42.10-P-054524 SEPT12 – 212.072/090/272 front brake vibration. Thickness fault on brake disk replace pads and disks.

LI82.85-P-051046 SEPT12 – 212 up to VIN 1A329706 & 207 to 1F085904 reversing camera intermittently has no picture; next/previous track function inoperative, perform COMAND software update.

LI82.70-P-054226 SEPT12 – 212, 207, 218 NTG4 mobile phone driver poorly understood & background noise audible during call, perform COMAND software update.

I recently purchased a 2010 and noticed the issue with the reverse camera. Having all of this information is extremely valuable before heading to the dealer for service.

THANK YOU!

Service Campaign 2012070002 SEPT12

Models 164, 171, 203, 204, 207, 209, 211, 212, 216, 219, 221, 230, 251, 463 Engines 272 and 273, MY 2005 – 2011 Camshaft Adjustment Solenoids - due to the settling properties of the seal, oil may leak from the camshaft adjustment solenoid dealers will retrofit four adapter harnesses onto the engine wiring harness. Covers any/all repairs due to damage from oil leak however, claims replacement of leaking camshaft solenoid is not permitted under consequential damage. Approximately 557,108 vehicles are affected - have dealer check VMI to determine if vehicle is included.

LI46.10-P-054502 – 204, 212, 218 scraping noises when steering the steering boot heat shield with aluminum ring may have loosened and is scraping on the steering shaft.

LI54.35-P-053444 – 204, 212, 218 Sindelfingen production up to December 2011, horns too quiet, inoperative or have poor sound flat plug on horn may have broken off, replace horn.

LI91.30-P-054637 – 212 up to VIN A362355 with seat heater, cable channel of seat heater visibly protruding and able to be felt replace heat mat with modified heating element routing.

LI47.20-P-054504 – 212, 207, 218, 204, 221, 246, 251, 164, 166 with diesel engine ( 642 & 651) complaints of running characteristics (cutting, hesitation) due to possible fuel delivery issues if the voltage or current test values deviate from specified values, the fuel pump must be replaced.

LI82.85-P-054716 – 204, 207, 212 with NTG4 Intermittently no audio from any source on startup satellite radio selection displays “Device Unavailable” backdate the SDAR’s software.

Thanbks for info.
 

"The Best or Nothing"? Yet more reasons why DAG fails to offer a warranty as good as that of Hyundai and Kia.

LI03.10-P-054702 Models with 276 engine-knock noises in crank assembly, repair requires the replacement of all connecting rods & pistons with wrist pins assembly.

LI15.12-P-054772 Models 212.074/274 (E63), 166.074/874, 172.475, 216.374, 218.374/974, 221.074/174, 231.474, 463.272/273 oil level query in IC not possible or oil temperature does not display in AMG menu – if ignition coils with part # 2769060160 are installed, replace all coils.

LI49.00-P-054888 Models 212/166/207/216/218/221 with 278 engine - warning + fault code P262600 or P262900 stored in ECU relating to oxygen sensor upstream of catalytic converter, replace left & right oxygen sensors and update ECU software if needed.

Which engine
 

How do I determine which engine I have?
Thanks for keeping us posted.

Check your datacard you have "272"980 .. ......

272 = 350 / 273 = 550 / 642 = BT
MY12 > 276 = 350 / 278 = 550

Thank You!!!
 

Thanks. I've made a note of this information.

Recall 2012110003 – MY12 218 bolts securing the striker for the engine hood latch tightened with reduced torque in subject vehicles. Approximately 23 vehicles affected.

Service Campaign 2012100005 – MY12 x164, 212, 221, 251 Selective Catalytic Reduction (SCR) control module software may not meet specifications. Update will optimize cold starting issues. Approximately 9,872 vehicles affected.

LI72.10-P-055044 – 207 up to VIN F174511 inside door handle inoperative, replace Bowden cable & clip.

LI91.30-P-054637 – 212 with seat heater (873) up to VIN A703331 lump under seat cushion cover, install modified heat mat.

LI68.30-P-053962 – 212 with burred walnut veneer wood finish (731) or burred walnut veneer designo brown (w60) UV can cause fading trim will be replaced, August 2011 clean point.

Burled wood trim?
 

LI68.30-P-053962 – 212 with burred walnut veneer wood finish (731) or burred walnut veneer designo brown (w60) UV can cause fading trim will be replaced, August 2011 clean point.[/QUOTE]
Is this different from TSB LI68.10-P-050415?

LI91.30-P-054637 – 212 with seat heater (873) up to VIN A703331 lump under seat cushion cover, install modified heat mat.
How can you tell if you have this situation?

Thanks once again for all you help.

Yes, not certain why they issued another bulletin rather than revision but looks like they added designo trim and clean point 8/11 validation (claim vehicles produced 8/11 > are equipped with modified trim).

This bulletin applies to your vehicle – within VIN range & datacard includes 873 (seat heater for left/ right front seats) have dealer check it.

i have the same question, too :confused:. i do see a "lump" on each of the front seats but not sure what that is :nix:.

If there is a visual lump, vehicle is equipped (873), and within VIN range have dealer check it.

Thanks again - and Happy Holidays!

roger that, konigstiger :y! thanks again for all your helps :bow:!

S-B-42.15/122 DEC12 Brake disks treated with Zinc Dust Spray Paint, re-spraying friction rings (outside & inside surfaces) with zinc paint is essential in protecting from corrosion, shuddering, and squeaking: all model years; 163,164,166, 170, 171, 172, 197, 202, 203, 204, 207, 208, 209, 210, 211, 212, 215, 216, 218, 219, 220, 221, 230,231, 245, 251, 463.

LI07.08-P-055310 Engine intermittently shuts off immediately after starting but does not shut off again on a restart. When started may exhibit rough idle for a few seconds. Symptom more common on restarts after short trips and relatively short engine off periods (10-60 minutes). ECU software update (version VC12.0.1) will be available mid February.

LI72.40-P-055045 Various function failures in front door; automatic window raising not possible / power window cannot be normalized (reset) / malfunction of central locking / illumination faulty – attempt door control unit reset by unplugging connector for about 20 seconds if unsuccessful replace DCU.

new member here, first post
 

I bought a 2010 350 last May. Thank you so much for this post. It has helped give me justification for requesting warranty claims with my dealership. They like to assume it is nothing wrong, or something that I was doing.

I took it in yesterday because of Bluetooth issues with calls, and also the streaming audio getting spotty after a few minutes. They updated the firmware but I don't think it's the latest version. It has the updated nav bird's eye view with the clouds, but it doesn't show the fan speed or temperature when changing the climate control. I'll check the version later in the engineering menu and post up.

Also, I asked them to check the wood trim because it looked like MatOhio's picture. (I am also from Ohio, go Browns and Bucks) They checked and said they didn't see a problem, so when I picked it up today I had to show them the LI and hold their hand while we went over to my car so that I could point it out. Then the guy saw it.

I'll be checking back with them on Monday, when the manager will be back. Is the firmware referenced in this comand 0009026706-001 the latest still?

Subscribed....although for some reason I'm not getting notified....which seems to be a recurring problem for me with this forum :confused:.

Service Campaign 2013010001 JAN13 – MY13 207,212, 218, 221, 231 with M278 engine left & right secondary chain tensioners installed at factory pressed too deep into cylinder head, dealer will remove check valve of tensioners. Approximately 167 vehicles affected.

Service Campaign 2012120003 JAN13 – MY12 218 Dealer will update ECM software, may not meet current specifications. Approximately 10 vehicles affected.

Service Campaign 201212004 JAN13 – MY12 212, 218 with M157 (AMG) engine dealer will update ECM SCN coding, injector coding may not meet current specifications. Approximately 24 vehicles affected.

LI46.35-P-055436 JAN13 – 204, 212, 207, 231 red display message “Power Steering Malfunction – See Owner’s Manual” immediately after engine start, steering assistance reduced; update software of electric power steering (ES) control unit.

LI77.00-P-055046 JAN13 – 204/216/218/GLK/221/205/213 with sunroof (without panoramic roof) moisture in the area of left or right A-pillar trim/headliner, replace water drain grommet.

LI82.60-P-055465 JAN13 – 164, 166, 169, 171, 176, 203.7, 204, 207, 209, 211, 212, 216, 219, 221, 230, 231, 231, 245, 246, 251 with Media Interface (code 518), 463 (EH3) iPod/iPhone music playback not possible; audible only on left/right side; iPod not charged – replace Media Interface connecting cable.

What if car's out of warranty
 

Great thread, can someone educate me as to how the local MB dealer uses the information in these bulletins? Is it the case that they are obliged to check your car for the issues listed, or do they wait for the owner to see a problem and complain? Is there a record of what checks have been made or work done?

I'm asking because I'm about to pull the trigger on a 2010 E550 with over 50k miles, i.e. out of warranty. The car has been serviced by MB. I will go through the car looking for the issues in the list but wondered how best to proceed if there's a problem.

BTW the missing tab on the rear fender sounds expensive, didn't see any other threads related to it, maybe it'll take more time to become evident.

thanks,

Peter

I also have the bumper issue, not sure if its just a tab or whole replacement.

I believe when you take your car in for either normal or warranty maintenance the system/computer lets them know if a TSB is applicable from the build date or VIN.

Yes. My experience is MB is conscientious about applying technical updates.

DTB & LI bulletins are covered under warranty (initial factory, CPO, extended, etc.) pulled by tech normally only upon customer complaint. If they document a specific range (i.e.: VIN, serial #, etc.) and out of warranty request goodwill repair based on production defect from MB rep covering dealership via service manager.

Recalls & Service Campaigns are covered out of warranty - no time or mileage limitations.

Request Vehicle Master Inquiry (VMI) from dealer this is a history of all warranty, maintenance, at cost repairs, etc. performed by MB for your VIN.

Recall 2013020002 FEB13 – X204, 204, 207, 212, 216, 221 model years 2011-2012 due to issues during molding process of supplier operating pressure & high operating temperatures may result in fuel leakage. Dealer will replace fuel filter. Approximately 5,773 vehicles affected – owners of affected vehicles will receive a letter, or you can have dealer check VMI to see if vehicle is involved.

LI27.60-P-055362 FEB13 - 212, 221 with 722.9 transmission / OM642LS (diesel) engine - deceleration upshift from 4th to 5th gear may be uncomfortable under certain driving conditions, dealer will update software & reset adaptation.

LI42.10-P-0555595 FEB13 – 212.091 E550 4matic, 218.373 CLS550 & 218.391 CLS550 4matic grunting noise from front axle area during medium / hard braking (similar to allowing vehicle to creep slowly from a stationary position with brakes partially applied), replace front brake pads.

LI82.85-P-055695 FEB13 – 207, 212, 218, 166, 172, 176, 204, 246, 463 COMAND does not start, cannot be operated, display remains dark. Problem disappears after lengthy idle period or after interrupting the power supply. Update COMAND control unit software. The software will be available with Xentry 03/2013 and Telematics DVD 03/13 (A 166 827 11 59).

LI07.08-P-055310 MAR13 - 276 engine all models, 278 in model 166 shuts off immediately after starting. Symptom is common on restarts after short trips and/or short engine off periods (10-60 minutes) – no relevant fault codes. Software update is now available https://mbworld.org/forums/5492959-post105.html

Indication:

I do have some of that going on, on my drivers seat.......but I don't think I want the dealer pulling my seat apart:nix:

LI91.10-P-055704 MAR13 – Model 207 & 204.3 front seat trim protrudes - caused by mounting clip loosening under load, increase clip forces.

LI82.62-P-055715 MAR13 – Model 207.3 poor audio quality from all sources after amplifier software update, flash again.

LI72.00-P-055756 MAR13 – Model 212 & 218 door seal on front & rear door loose, replace doorframe seal.

Thanks much, Konig!

I dunno. Maybe the issue suggests other potential failure of the heater or seat cover???? And who wants an electrical failure going on between your legs!? Not exactly the kind of lump you want there.

(Note that I resisted any comment about the dealer "pulling your seat apart" when you bought the car.:))

Dealer replaced rear bumper due to this issue on my 2010.
Thanks.

LI88.20-P-052891 - 212 rear bumper sticks out in area of rear lamp. Bumper experiences thermal expansion mounting rails (fender area) cannot sufficiently hold the bumper in place. If bumper is not equipped with additional latch, it should be replaced. Note since JAN11 bumpers are equipped with additional retaining tab.

Would any one have a picture of what this looks like?

not sure if post #49's pic good enough :nix:.

LI82.85-P-055695 FEB13 – 207, 212, 218, 166, 172, 176, 204, 246, 463 COMAND does not start, cannot be operated, display remains dark. Problem disappears after lengthy idle period or after interrupting the power supply. Update COMAND control unit software. The software will be available with Xentry 03/2013 and Telematics DVD 03/13 (A 166 827 11 59).
Here we go again with issues related to COMAND!

oh no! Elcid is jacking konig's deal!:)

Huh?
 

Not sure what the above means (Koning's deal?), but for clarification. My comment is reference to how often COMAND issues seem to come up and how complicated the "fixes" are. Even then the results seem to vary a lot as to success. :zoom:

LI6805-P-055754 APR13 - Owner cannot program mirror from handheld transmitter Genie & Wayne Dalton door opener NOV 2010 or later (use Intellicode 2 encryption), transmitter is backwards compatible to mirror by changing to Intellicode1 - see 055754 attachment.

LI01.40-P-056159 APR13 – 172, 204, 207, 212 with engine 271.8 EVO oil loss in area of rear crankcase – transmission bell housing, check threads of transmission mounting, holes of cylinder head bolts 9 & 10, and replace sealing ring on engine temperature regulator.

LI77.21-P-051114 APR13 – 207.3 roller blind of panoramic roof is blocked, broken, fabric torn. Replace roller blind, check guide rails replace if necessary. Possible causes, antenna cable was incorrectly routed and/or sealant bead on frame at center rear protrudes too far causing blind to chafe.

LI91.18-P-049463 APR13 – 204, 207, 212 multicontour seat cushion becomes detached fastener clips will be installed reattaching cover exactly - see 049463 attachment.

LI72.00-P-055920 MAY13 – 212 up to VIN A663422 outside handle does not return to default position, replace bearing bracket.

LI88.50-P-053768 https://mbworld.org/forums/5265348-post86.html incorrect installation or misalignment (protrudes at sides) MAY13 revision, roof spoiler added.

Becker MAP PILOT (BMP) code 509 or preinstallation 508:
http://www.mbusa.com/mercedes/access...rtNo:BQ6829777

LI82.61-P-055955 APR13 – BMP navigation function boots only to Becker logo; display freezes; startup time takes a long time; displays responds with delay, update software to version 12/12.00 (1669027304), firmware to R22.3.1205 or higher, and “free of charge” navigation software to 2.0.50 or higher.

LI82.61-P-055979 APR13 – BMP navigation volume reduction is inoperative. Function operates in relation to volume setting. Check as follows: set music volume loud, during navigation announcement reduce volume, activate audio volume reduction setting and check. If a difference is heard in audio volume reduction during check, system if OK.

LI82.61-P-056044 APR13 – BMP house numbers not found when addresses are entered via Audio/COMAND controller, update software to 12/48.00 (1669021105), firmware to R26.3.0130 or higher, and “free of charge” navigation software to 2.5.26 or higher.

LI82.61-P-055954 APR13 – BMP “No navigation module connected” appears in display, update software to 12/21.00 and firmware to R22.3.1205 or higher. In addition, check tightening torque of threaded connection between bracket and glove box, and low voltage differential signal (LVDS) line @ radio.

Service Campaign 2013040003 MAY13 – 2013 models 212 & 218 right horn bracket may not be to specification, dealer will re-torque.

LI88.30-P-056180 MAY13 – 218 front wheels with 18-inch tires scrape against front wheel liner, replace wheel well liners inclusive of front engine compartment paneling.

Does this apply to a 2012 E550 cab? I am experiencing vibration under braking especially in freeway. Car has less than 8000 miles and 1y1mo old and the dealer is refusing warranty.

Bulletin documents only 212 however, EPC shows original front brake discs replaced for 207.473 (E550 Cabriolet):

Front part # 2214210812 replaced by 2044211212 – request service manager get MB rep covering dealership involved to approve replacement considering mileage and only one month out of 12 month/12,000 MB brake warranty https://mbworld.org/forums/2089508-post1.html

LI67.30-P-056196 MAY13 – 207 up VIN F215729 vertical scratches on front and/or rear windows replace window and install new trim strip.

LI49.20-P-056353 MAY13 – 212, 218, 164, 166, x204, 221, 251, 463 with 642 BT engine (code U42) heating element of AdBlue tank malfunctions, replace faulty components program SCR control unit with new software.

LI07.08-P-056434 MAY13 – 276 engine intermittently shuts off at idle when vehicle is stopped for some time at a stop sign, traffic signal or similar traffic situation. Update MED control module software.

LI01.60-P-056340 JUN13 – 276 engine thread on timing case in area of oil filter housing shows signs of leakage (see attachment), install new bolt 0029901103.

LI62.25-P-056043 JUN13 – 212 & 218 deformation of engine compartment soundproofing due to water ingress. Install optimized seal part # 2126280800.

Do they do an alignment after replacing two front struts?

Yes they should. Matter of fact, if you have a 4MATIC, they should complete a 4 wheel alignment.

Water leak help
 

My 2012 W212 Vin A617810 leaks water into the foot well on the drivers side. Is there any TSB on this? Appreciate any info before I take it into the dealer.

What kind of water?
 

I had a car once where water was leaking from the A/C into passenger floor due to poor assembly quality and design of drain location. Does it leak in rain? when washing car? Turn a hose on windshield and then on the area at base of windshield. Might help narrow it down.
Good luck!

Water leak
 

Seems most noticeable when I hose the car down for a wash.

Konigstiger:

With reference to Post #159 dated yesterday in this Forum: https://mbworld.org/forums/e-class-w212/446961-2012-e350-blown-motor-less-than-1000-miles-what-my-options-7.html

Are you aware of the TSB which the poster states his dealer informed him exists, necessitating a 2012 E350C engine rebuild due to bad wrist pins?

Sincere thanks, as always!

Yes. I had my front rotors replaced on my 550 cab for this very reason. HOWEVER the dealer was very specific that they did me a "favor" as a long-time customer as I had the service done just after one year and they would not do it over 12K miles or 12 months.

I would take it in ASAP if you're at 13 months now

Delivering my car for replacement of front and rear windows:)
Took a while for the local dealer to confirm

Service Campaign 2013050005 JUN13 – MY 2011 212, 204 and X204 transmission noise, may not meet internal specifications replace transmission. Approximately 17 vehicles affected. Have dealer check VMI to see if vehicle is included.

LI82.61-P-056388 JUN13 – Becker MAP PILOT navigation announcements inoperative, update software to navigation module.

LI27.19-P-056458 JUN13 – 212.098 & 298 (BLUEHYDRID), 212.095 & 195 (HYDRID) various transmission complaints, flash transmission control unit - automatically flashes engine control unit (ECU), battery management system (BMS) and power electronics (LE_TUBE) at the same time.

LI09.20-P-056492 JUN13 – 212,077 & 277 (E63) up to engine # 60 005808 CEL lights up / engine shakes at idle, replace intake manifold seals using modified aluminum mounting bolts.

Subbed.

konigstiger - two questions ...
1. '71 Pinto, really?! I had one of those until we dropped a V8 in the back and turned it into a dragster. It died an honorable death when a driver wrapped it up a few times too many ...
2. I see some Service Bulletins/TSB's/LI's that mention a specific model year (MY) and some that don't. How do I tell the differences between MY variances?

;)

If bulletin references model year (MY), production range, and /or VIN range etc. coverage is of course limited. If not, bulletin should cover listed model(s) regardless of MY and VMI (vehicle master inquiry) confirms eligibility - i.e.: bulletin references modified part without MY, given production date VMI and/or EPC (electronic parts catalog) should confirm if part was already installed at production.

Hi D,

My new to me MY10 E550 has this bumper issue is that possible you can send me a copy of the bulletin?

Thanks

My 2011 e350 had the same bumper issue. Please send the bulletin.

Konigstiger, thank you for posting this info.

I dropped my car off (2012 E550 sedan) at the dealer a couple of days ago because of a vibration in the steering wheel while braking, along with a strange noise in the front which I thought was normal.

The tech could not find anything wrong. I then went online and found this forum and I think I found two service bulletins you posted that apply to my car.

LI42.10-P-0555595 FEB13 – 212.091 E550 4matic, grunting noise from front axle area during medium / hard braking (similar to allowing vehicle to creep slowly from a stationary position with brakes partially applied), replace front brake pads.

LI42.10-P-054524 SEPT12 – 212.072/090/272 front brake vibration. Thickness fault on brake disk replace pads and disks.

I emailed the dealer with the info and hopefully they end up replacing the brake pads and disks on my car. One question, when Mercedes issues a service bulletin and the dealer performs the repairs they are reimbursed by Mercedes for parts & labor, right?

Yes, if under warranty.

From my understanding, yes they get paid for the parts and labor but they have an internal labor rate that amounts to less than what a private mechanic would get paid. Maybe even 30% less than a private mechanic sometimes. This is why dealers are annoyed at doing warranty work. Can anyone chime in on this?

Correct, discounted labor & parts

Could you please pm me LI32.25-P-051123 FEB11 ? I have been getting the dull thumping while turning sharply at low speeds.

The dealer says the tech knew about the bulletins, but refuses to replace the pads or rotors under warranty because my car is 19,000 miles (warranty for pads & rotors is 12,000 miles) and doesn't feel the vibration is bad enough. They said if I want to replace the front pads and rotors it's close to $1,000. Very disappointed.

Which dealer is refusing to do the work? Get the word out via this forum, yelp, etc. to warn your fellow MB owners. A premium brand should take care of the owners of their cars. Thanks.

Is this the first time you have documented this complaint?

Is there a history of this complaint made by you on previous visits before 12K elapsed?

Have you talked to the Service Manager? MBUSA?

Good news. After voicing my displeasure with my service advisor, he spoke to the service manager who then spoke to MBUSA and they approved a one time "good will" repair and replaced the front brake pads and rotors at no charge. The car feels much better now. Thanks.

LI91.45-P-056629 JUL13 – 207 switch for seat belt extender inoperative, coding problem in rear control unit.

LI91.10-P-054143 JUL13 – 204, 207, 212 and 218 seat fore/aft adjustment nonfunctional, replace motor, shafts and motor retaining plate.

LI05.1o-P-056435 JUL13 – 276, 278 and 157 engines rattling noise after start for several seconds, install check valves/replace left & right secondary chain tensioners.

LI68.10-P-056727 JUL13 – 207, 212 and 218 glove box squeaks/rattles, attach felt to mounting at top left.

LI46.35-P-055485 JUL13 – 204, 212, 207 and 231 with direct steering (code 211) engine does not start, or various fault messages in IC immediately after engine start and servo assistance reduced, update steering software.

LI27.19-P-056898 AUG13 – All models with NAG2 (7-speed transmission) in combination with OM651 or OM642 (diesel); 218 & 212 with 278 + 4matic delayed start-off from standstill / lurch when coming out of power-free state / jolt when brakes are released, update software.

LI91.10-P-056733 AUG13 – 207 rattling noises from backrest while driving, install felt.

LI30.30-P-056782 AUG13 – 218,166, 172, 204.9, 216, 231 production date 4/1/13 to 6/30/13 with Distronic plus (233), system occasionally reacts too sensitively to vehicles in adjacent lane, perform initial startup of radar sensors control unit - may contain default values instead of vehicle-specific values.

LI54.65-P-056779 AUG 13 – 212 & 207 facelift (804), 117 Parktronic cannot display any obstacles only ready LED lights up, update control unit software.

LI82.70-P-056963 AUG13 – 207, 212, 218 Connect device function in Telephone menu is sometimes grayed out following system start although Bluetooth is activated it is then not possible to set up a connection between phone & COMAND, update COMAND online control unit software. Note: Problem is rectified after bus idle or after resetting COMAND (hold down ON button for 8 seconds).

LI82.60-P-056890 AUG13 – 212 no/poor AM radio reception, insufficient ground connection of antenna amplifier.

LI88.20-P-056908 AUG13 – 212 (954, P96 or 772) facelift wind noise/whistling at windshield, possible cause gap between bumper & chrome surround of radiator trim – see picture.

LI07.08-P-057165 AUG13 – 212, 204, 164, 221, 230 with 272 & 273 engine radiator fan runs at 100% + fault code 2237 stored, update ME control unit software.

LI54.71-P-056477 AUG13 – 212 & 218 with Blind Spot Assist (234) or Active Blind Spot Assist (237), 164 with (234) inoperative, replace radar sensors with additional silicone sealing.

LI30.30-P-057139 AUG13 – 212 & 207 with Collision Prevention Assist (258) may warn for no obvious reason, update CPA control unit software.

LI82.85-P-057169 AUG13 – 212, 207, 218, 221 with retrofitted iPhone Drive Kit Plus COMAND display flickers or briefly turns green/red/black, replace audio-video adapter cable from Apple - not claimable under warranty.

LI54.30-P-056977 AUG13 – MY2014 212, 207, 218 analog clock sporadically executes a normalization sequence, replace clock with part # 2188270070. Sunlight rays can pass through the face to the inside causing the IR sensor to detect loss of synchronization the clock then runs a normalization sequence.

LI82.85-P-057016 AUG13 – 212, 207, 218 with retrofitted iPhone Drive Kit Plus stability improvements (poor sound quality, distorted audio output, etc.), update DKP control unit software. Following parts are affected: 1728700296, 1728700496, 2128200376, 2128200476, 1768200176.

Konig, I hate to bother you --- you do so much for us.

HOWEVER :), LI30.30-P-057139 AUG13 – 212 & 207 with Collision Prevention Assist (258) may warn for no obvious reason,

In my MY 2011 212 P2, we frequently get a "beep beep" for no reason, no cars or any kind or obstruction nearby, no chance of police or other radar emissions. And there is absolutely no message of any kind. Disconcerting at times . . .

Is it possible that's what this notice is talking about?

Konigstiger,

Could you please translate what NAG2, OM651 / OM642 are? I have a 2013 E550 with this issue. I had the vehicle into the dealer last week, but the technician said that the latest software is installed.


LI27.19-P-056898 AUG13 – All models with NAG2 in combination with OM651 or OM642; 218 & 212 with 278 + 4matic delayed start-off from standstill / lurch when coming out of power-free state / jolt when brakes are released, update software.

NAG2 = (Neues Automatische Getriebe 2) New Automatic Gearbox 2 another name for 7-speed transmission. OM651 & 642 = diesel engines. Check your email.

Got it! Thank you. I've just noticed another anomaly with the transmission in "S" mode. The car will not start in 1st gear if it was originally started with "E" when shifted from Neutral. Shifting back to Neutral and then to Drive restores the 1st gear start. This may be all related, but not sure. I'll let the tech sort things out.

The technician made the following determinations:

The car IS starting in D1 when in "S" mode. The engagement surge that I was feeling (depressing the left paddle) is due to the transmission clutches being reengaged after running free. Also, MBUSA says that the jolt that I have been noticing is NORMAL (WAD) for engine 278 and 4Matic. The bulletin applies to MY2012 and up if the transmission software update had not been installed. The additional tip about greasing the drive shaft to address the issue apparently does not really fix the complaint, but can lessen the jolt if there was inadequate grease.

Did you get your issue with knocking noise fixed? My vehicle sounds the same and warranty will end so soon.

Heard from a fellow mercedes owner with E250CDI that there is an factory order to change the diesel injectors on W212 diesel cars.
Anybody got the bulletin I can take to my dealer?

LI91.40-P-057018 SEPT13 – 212, 176, 242, 246, 204, 117, 222 creaking noise from left or right front seat belt height adjustment mechanism, replace belt height adjuster.

LI82.85-P-057192 SEPT 13 – 212, 218 w/COMAND NTG 4.5 Gen2 intermittently no audio output regardless of selected source immediately after engine start, update COMAND control unit software.

LI82.85-P-057191 SEPT13 – 212, 218 w/COMAND NTG 4.5 mute function that was activated before last ignition off is intermittently no longer active, update COMAND control unit software.

LI88.50-P-057020 SEPT13 – 218 with AMG rear spoiler lip, trunk lid does not open fully via remote unlocking increase preload of spring by moving to the fourth hole on both sides.

2010 E350 V6 Coupe , 26k miles
Front noise left side on low speed , dealer was no help
Local shop did inspection , verdict - front struts / or front upper mounts get loose :confused:
Asked dealer again to do inspection , success - dealer is going to replace both front struts under warranty
After this checked Bulletins , i think this is a common issue with these cars

LI32.25-P-051123 FEB11 – 212 without Airmatic (489), 207 without vehicle dynamics (483)
dull thumping noises or metallic rattling from the area of the front axle occurring @ speeds 10-45 mph, modified front struts should be installed.

many thanks to konigstiger :) will report if issue get fixed

OCT 13 LI27.19-P-056610 for Design Group 27.19 Transmission -- (thanks to david55838 on benzworld)
improves harsh 3-4 and 4-3 and 4-5 harsh shifting; all 212 with M276 experiencing this problem

Thanks. Now if they would just admit to this issue with 2011 M273 engines!!!!!!

Jerry

Service Campaign 2013100003 OCT13 – MY13 212 & 218 incorrect plastic nuts installed on under-floor paneling that could cause the panel to detach in snow or ice conditions, dealer will replace under-floor nuts. Approximately 25 vehicles affected.

Service Campaign 2013090008 OCT13 – MY13 166, X166, 204, X204, 207, 212, 218, 231mbrace software does not correspond to current production configuration, dealer will update. Approximately 47,148 vehicle affected.

Service Campaign 2013090002 NOV13 – MY13 166, X166, 212, 221engine control module does not correspond to production configuration dealer will update software. Approximately 11,715 vehicles affected.

LI54.21-P-057404 OCT13 – 212 VIN A703805 to A736747 image interference in night view system (610), diffused light screen of the night view camera is missing.

LI82.85-P-057407 NOV13 – 117, 166, 172, 204, 207, 212, 218, 246 fuel consumption indicator in system menu is incorrectly scaled or missing, update COMAND control unit software.

LI32.22-P-057569 NOV13 – 212 & 218 Airmatic (489) compressor inoperative, prefuse box is faulty.

dealer replaced both struts under same recall
70% fixed , still some minor noises
lubed hood mounts , - another 10% fix
after detail inspection found control arm big bushing ( aka trust arm bushings ) loose / fail
dealer is going to replace them next week as well

keep digging if you want to have perfect MB suspension :)

LI32.25-P-048218: THUMPING NOISES FROM VICINITY OF REAR AXLE
 

I'm getting a dull thud/thump from my rear axle on my 2010 E63 AMG when going over bumps, specifically depressions such as manhole covers. I searched through this forum for service bulletins related to this particular issue but couldn't find any. I then did a web search and came across this:

LI32.25-P-048218: THUMPING NOISES FROM VICINITY OF REAR AXLE

Does anyone have any more info on this? Not even sure if it's applicable to the E63's suspension.

Thanks for any and all help.

LI32.25-P-052035 - CREAKING/SQUEAKING NOISES WHEN STEERING
 

Does anyone have any info on this service bulletin? I've got really bad creaking/squeaking from the steering wheel on my 2010 E63. Just had it at the dealer and they lubed the boot & shield on the steering shaft which didn't do squat especially this cold morning here in Boston.

Thanks!

048218 applicable to MY10 e550 coupe (207) with Vehicle Dynamics Package (483).

052035 not applicable to e63
LI32.25-P-051645 FEB13 - 212.#77 / #74, 221.#74 creaking/squeaking noises from front axle when steering, replace spring cup mountings and suspension strut rubber end stop.

Thanks for the info.

I just had Service Campaign 2013110002 Fuel Sys ECU done on my E550. What does it do?

I hear a thump every morning when i reverse out of my driveway and hit the brake to switch gears to drive. Could this be the same bulletin that applies to my issue?

Thanks.

here is the list of fixes for my front suspension
so far so good now ...

Shock absorbers 2 204-323-30-00 waranty
Dust cap 2 204-323-04-38 waranty
Hydromount 2 204-333-11-14 waranty
Elastomeric cap 4 211-333-06-97 waranty
Bront bearing adjustment both sides DIY
Hood mounts lubed DIY

I have a similar issue - though not every day.

Yes, although now that I think of it, it's not everyday... :nix:

I've got the same issue with my 2010 W212. Every few days in reverse.

Service Campaign 2013100005 NOV13 – 2013 204, x204, 207 seam seal on the under-floor may have been damaged during manufacturing process, dealer will repair. Approximately 1,664 vehicles affected.

Service Campaign 2013110002 NOV13 – Model years 2011-2013 166, x166, 172, 204, x204, 207, 212, 216, 218, 221, 231, 251 fuel system control module software does not correspond to current production configuration Check Engine Light (CEL) may occur, dealer will update software. Approximately 123,831 vehicles affected.

Service Campaign 2013110011 DEC13 – 2013 212 Hybrid Operators Manual may not have been installed, dealer will install. Approximately 11 vehicles affected.

LI88.60-P-049559 APR12 – 212 fuel filler flap deformed, opens/closes poorly. (1) Paintwork does not cover entire area of attachment point between rear of fuel filler flap and filler flap arm, substrate absorbs moisture at this point. (2) The retaining strap can become twisted from opening the tank filler cap this can cause the retaining strap to wedge behind the hinge arm obstructing closing sequence. The height of the stop buffer located on the left of the tank recess can impair the opening and closing behavior of the fuel filler flap. Remedies: cut off stop buffer on the left of the tank recess as this will help to improve the opening and closing behavior, replace filler flap.

LI88.70-P-056690 OCT13 – 212 (code(803) outside mirrors can fog up at outside temperatures below 15 degrees C (60F) up to production 1/2013 heated mirrors are actuated only 10 minutes after engine start, code front door control units so mirrors are actuated continuously.

LI46.35-P-057738 NOV13 – 212 4matic & 212 AMG facelift (804) with direct steering (211), battery discharged. DS control unit does not switch to idle state when vehicle is locked, update software.

LI54.25-P-056472 NOV13 – 166, 204 (GLK only), 212, 218, 246 key is not recognized vehicle cannot be started and/or transmission shifts to “Automatic P”, replace electronic ignition switch (EIS).

LI80.61-P-057752 NOV13 – 212 VIN A909083 – A920630 & 222 A020500 – A023037 Keyless Go (889) vehicle cannot be opened/closed or started via KG manufacturer fitted key with wrong processor. KG function worked in the past - yes, perform diagnostics; no, replace affected key.

LI27.19-P-057771 DEC13 - 212.098, 298 Bluehybrid, 095 Hybrid & 222.057, 157 Hybrid various transmission problems including intermittently cannot shift into reverse also CEL may light up. Oil pressure switch is faulty. If problem occurs in combination with fault code P087000, replace TCU.

LI72.20-P-053019 DEC12 – 212.2 up to VIN 663422 & 204.2/204.9 with code 809 up to 942003 automatic liftgate malfunctions (gap dimensions not OK, reverses direction when closing, and/or does not open completely). Jamming of the liftgate lock caused by faulty actuation from rear SAM can bend the left tailgate hinge. Replace hinge and rear SAM.

LI72.40-P-058061 DEC13 – 204 & 212 normalization of left or right front door power window may intermittently be lost or automatic window raising not possible, update door control unit software.

LI82.85-P-058185 DEC13 – 166, 204 & 212 with engine OM651 intermittently COMAND display may show fault message “Anti-theft protection activated” cause, disrupted CAN communication.

LI82.61-P-058186 DEC13 – Becker MAP PILOT (code 508 or 509) cannot be operated navigation display freezes, perform software update.

LI46.35-P-057867 JAN14 – 207 VIN 1F 236519 to 249267 (steering gear 2074603100) & 212 1A 831730 to 907236 (2124608900) with direct steering (code 211) except 4matic & 212.#074/75/77 scraping/sqeaking noises when steering quickly from lock to lock in both directions, replace steering gear.

I just bought a CPO 2011 E350 4Matic Sport. I noticed today when sitting idle, the AC/Heat blower fluctuates in speed when set at a level 3 or higher. You don't notice it with the radio on and it is hard to notice while driving with the radio off. But sitting at a light or in park....it blows harder, then softer, etc. I did a Google search and came across a website called eautorepair.com (mitchell's). It shows a TSB that may be my issue, but want you to pay a subscription to see it. So a couple questions:

** Is a site like that worthwhile to pay to use to get access/alerts on TSB's for my MB/

** Does anyone have details of the following TSB: LI83.30-P-056980 · BLOWER OUTPUT OF AIR CONDITIONING FLUCTUATES, LOSES POWER OR STOPS OCCASIONALLY

Thanks in advance!

heater blower
 

You have a CPO warranty---USE IT1

cool. thanks much for posting these. this one's not really that bad, but good to know they'll fix the squeak.

Any TSB out there for front seat clicking noise

LI88.70-P-056690 OCT13 – 212 (code(803) outside mirrors can fog up at outside temperatures below 15 degrees C (60F) up to production 1/2013 heated mirrors are actuated only 10 minutes after engine start, code front door control units so mirrors are actuated continuously.
I thought the "heated" mirrors were only active when the rear window defogger is activated and it is on a timer.
Haven't experienced this problem on my 2010 even at temps as low as 30 degrees F.
Thanks.

Bulletin applies to MY13 (803). Temperatures below 15°C (60°F) the heated outside mirrors are actuated continuously and they can always be activated by turning on the rear defrost.

LI46.15-P-058505 FEB14 – 166, 172, 197, 204, 207, 212, 218 creaking noise when adjusting electrical steering column, lubricate thrust piece of steering column.

Major problem : at dealer now and in Bangladesh it is not that easy to deal with this
 

My car is a E250 2012 coupe Avantegarde and starting to experience power loss in all sectors and this issue consistently and at deLer at least 20 times since I bought the car, frustrating but trying to deal with issue. Is it better to get in touch with Daimler, Germany instead is my question ?

Is that enough to solve the problem
 

My steering wheel is making grinding noises when car has been increasingly used over a period of a day, is this solution enough to do away with problem ?

Re: seam seal and fuel system control module
 

I want to be 100% sure that these two issues are affecting my Benz and then bring up the issue to my dealer. In a third world country it is not easy to do these things so how do I confirm that these issues are in fact a reality ?

I had this issue on my first 2014 E550 and they replaced the entire steering column and the steering gear, and the problem went away. I had the grinding all the time though.

You think the 7G on my 2012 E250 Coupe is of same build and issues oriented ? How can I be certain ?

LI63.30-P-058687 MAR14 – 207 production date as of 9/09 up to 10/10 sloshing noises from area left & right rocker panels / longitudinal members drain water, preserve with cavity wax, and replace grommets.

LI83.00-P-058688 MAR14 – 212 hybrid AC intermittently does not cool, replace evaporator shut off valve.

Service Campaign 2014020004 MAR14 – MY14 212 & 218 weld seams at rear axle cross member may not be to specification, check and repair left & right weld seams. Approximately 1263 vehicles affected. Have dealer check VMI to see if VIN is included.

Service Campaign 2014030001 APR14 – MY13-14 212 hybrid transmission control module software does not correspond to current production configuration, update software. Approximately 342 vehicles affected.

LI72.20-P-054311 APR14 - 212.2 up to VIN 670422 liftgate reaches upper end position, single noise coupled with jerky movement in the left hinge area perform variant coding and normalization of liftgate control unit.

Glad I started lurking on the W212 page! This stuff is great. Looks like it covers my car too (2013 C250 with M271 Evo and 7G Plus). Glad to see I don't have any issues to deal with.

Do you think other auto manufacturers have this many bulletins and recalls? Or do they have just as many problems but don't report at the dealer level?

For those of you who had this issue, how much did the rear bumper stick out at this point? There is small gap between the bumper cover and the body panel, but it does not protrude out from the side of the car. My car is pre Jan 11 but my service history does not show this repair. While the additional latch may not be there, perhaps it is not a problem for all.

It's like you took a photo of my engine compartment. I have this deformation. Since I am out of warranty, should I bother fixing this myself or just leave it? Is lack of soundproofing performance the only downside?

While I can feel a slight bump in the front part of the seat, my datacard (thanks again) does not show option 873 even though the car has seat heaters and my vin is below A703331. Perhaps this is specific to a later model year or separate heat seater option.

"It's like you took a photo of my engine compartment. I have this deformation. Since I am out of warranty, should I bother fixing this myself or just leave it? Is lack of soundproofing performance the only downside?"


Wow, Same here! I would like to get this fixed. It's an eye sore to me, but obviously only me.

What pictures are you referring to?

If it were me I would request goodwill replacement. Bulletin documents inferior seal installed at production allows for water ingress causing soundproofing to deform, MB requires modified seal to correct – one can either discuss this with service manager or have CAC (800-367-6372) open a case for review.

LI82.85-P-058859 Apr14 – 212, 218, 207, 117, 156, 166, 172, 176, 204, 216, 221, 231, 246 w/retrofitted Drive Kit Plus (DKP) for iPhone 4/4S/5/5S/5C server unavailable or Car-to-X unavailable error may appear when driver wishes to report a hazard manually and heightened security rules have been activated in the system update DKP control unit software in addition, customer should update iPhone app to latest version.

LI82.85-P-058928 Apr14 – MY14 212, 218, 207, 117, 156, 166, 172, 176, 204, 231, 246, 463 Sirius application constantly displays “Updating Channels” audio output from most recent satellite station is present but no other stations can be selected. Complaint occurs sporadically after ignition on following ignition cycle issue disappears temporarily. Press COMAND on button for about 10 seconds this will perform soft reset issue may return after next CAN sleep – do not replace any parts matter under investigation.

LI88.20-P-058905 Apr14 – e63 wind noises area of bumper/engine hood between 45-80 mph, gap between trim and bumper greater than specified dimension remove front bumper and glue chrome frame to ensure stability.

Service Campaign 2014040004 May14 – 2014 E-Cabriolet trunk seam seal may not be to specification, dealer will rework seal. Approximately 55 vehicles affected you can have dealer check VM

LI98.00-P-058914 JUN14 - Exterior clearcoat finish is peeling, flaking, or exhibits bubbles under the surface, improper adhesion of clearcoat. Dealer will refinish affected areas.

Does anyone have access to tsb for this one? Even though my ecu is stil tuned, the added power is lost after this service. I need to know what exactly was done. Thanks

Procedure:
DAS/Xentry 09-10/13 with add-on 3153 or higher.
Connect battery charger (battery voltage >12.5V).
Ensure all electrical consumers are switched-off.
In the event of software/SCN update issues, contact Star Diagnosis User Help Desk.

Update fuel system control module software (FSCU):
DAS: Control units / Drive / FSCU / Control unit adaptations / Control unit programming.
Xentry: Control unit view / Drive type / FSCU / Fuel pump / Adaptations / Control unit programming.

Verify fuel system control module software number change after performing the software update.

Much appriciated. Thanks

LI65.00-P-059054 MAY14 – 2014 207.4xx AIRCAP functions excessively activated wind screen at rear seat extends, 25 mph or higher windshield wind deflector extends, speeds below 9 mph retracts automatically. MY13 both wind screen and front deflector remain raised until deactivated or vehicle is turned off. Dealer will/can revert function to MY13.

LI.85-P-059083 MAY14 – (NTG 4.5) 207,212,218 code 088, 803 or 804; 204 code 802; 166,117172,176,204,231,246 code 803 or 804; 463 code XZ2/3 sporadic failures of Audio/COMAND display unit. Check: for fault codes; connections; cable set chafe marks/crushing; software update if none rectify the complaint create PTSS case.

LI54.65-P-059114 MAY14 – 212 code 501 produced up to 7/14; 222 code 501 up to 5/20/14; 166 code 501 up to 7/14 at night picture from camera in display on head unit can appear too dark, software update with optimized parameters is available.

Service Campaign 2014050002 JUN14 – 2014 212 & 218 transmission control module (TCM) does not correspond to current product configuration low transmission oil temperatures combined with certain driving patterns may affect engine running characteristics, dealer will update TCM software. Approximately 640 vehicles affected.

LI72.40-P-059215 JUN14 – 212, 207, 204.2/3/9 (code 237/804+054) active blind spot assist intermittently inoperative. Front door control units sporadically detect false short circuit, flash left & right DCUs.

LI54.21-P-059247 JUN14 – AMG 212.074/75/76/92; 218.374/76/92; 463.272/273 no double-clutching function (exhaust system sound) in transmission mode S & M, update engine control unit software.

LI49.20-P-059246 JUN14 – 117, 176, 204, 212, 207, 218, 172, 246, 166, 221 with 651 engine. CEL – stored fault codes P245997, 246397, 245900, 246385 or 246309 follow guided tests in XENTRY, which have to be fully processed.

WE HAVE A E63S 4MATIC WITH A WHISTLING NOISE WITH WINDOWS UP @ 67-75 MPH AND THEY FILLED THE GRILL IN WITH MORE MOLDING AND FILLER BUT IT IS STILL THERE, ANY HELP THE LAST OF THE VIN IS EA973872

THANKS
EDDIE

AND IT IS WORSE WHEN IT JUST GOT WASHED OR RAINING

Stand alone thread
 

You might want to post this as a stand alone thread.

Here is a list of W212 TSB's: https://www.eautorepair.net/app/TSBS...tic&PS=2&MA=15

Service Campaign 2014030001 JUL14 - MY13-14 212 Hybrid update transmission control module software. Approximately 342 vehicles affected have dealer check Vehicle Master Inquiry (VMI) to see if VIN is included.

delete

Hi konigstiger,
Any new update? Thanks.

To date a few released for 222, one for 221 but nothing for 212.

:urock:

LI25.00-P-059830 SEPT14 – Wet Clutch AMG vehicles with Eco Start/Stop & VGS4 jolting on start off after engine Eco restart, update engine control unit (ECU) & transmission control unit (TCU) software + perform wet clutch adaption.

LI82.10-P-059909 SEPT14 – 207, 212 with full LED headlamps (640) as of 2014 noise from headlamp area with vehicle parked and ignition off. Headlamp cooling fans may run for an extended duration due to latent engine heat or other ambient temperature related factors. If headlamps are fully functional and no fault codes are found this is considered normal.

LI46.35-P-059842 SEPT14 – 204, 207, 212 with direct steering (211) except 4matic, warning message “Power Steering Malfunction – See Owner’s Manual” and steering assistance is reduced if 2129017404 is installed update ES control unit software any other number create PTSS case for MB assistance.

E 63 A MG 2010 - M 156 engine
 

Are you familiar with Technical Service Bulletin LI01.30-P-051567 from Arpril 14, 2011?

What action would you recommend?

Thanks for your help and great forum on the W 212

Ricardo Hellbrügge

Service Campaign 2014010001 OCT14 – 212 Hybrid starter may not reach the internally required number of starting procedures. In such case, the stop-start function would no longer be available. During the required maintenance service (every 10,000 miles) starter counter is noted. Xentry will indicate the need to replace the starter and ring gear when specified values have been exceeded. Approximately 494 vehicles affected. Have dealer check Vehicle Master Inquiry (VMI) to see if VIN is included.

LI82.70-P-060004 OCT14 – iPhone exhibits various faults after updating to iOS8 and/or Bluetooth connection between iPhone & COMAND is disrupted, under analysis by Apple perform software update when newer version is available.

LI82-P-060002 OCT14 – Digital DriveStyle app does not lunch automatically, iOS8 software from Apple does not support automatic launching - manually launch after connecting with Drive Kit Plus.

LI54.10-P-060034 OCT14 – 212 hybrid (code ME04) vehicle cannot be unlocked, engine does not start, silent-start inoperative replace power electronics/distributor & starter battery.

LI91.29-P-059833 204, X204, 207, 212, 218 with option code 275/memory package (may also have 242/ RH seat w/memory) seat/column non-functional on startup when vehicle sits for a long time, change power supply circuit from ckt 30g to ckt 30.

Service Campaign E250BT
 

We just had it done, my wife misplaced the paperwork so I don't have the campaign number but it is for the MY14 with the 2.1 liter engine. Timing chain tensioner seal ring needs to be replaced due to leakage. I will try to find it and post it on here. Just wanted to get the word out. Happy New Year everyone!

Service Campaign 2014110004 DEC14 2015 212, 207, 166, X166, 172, 204, 231 COMAND control module software customer may not be able to change channels during SDARS reception display shows “Updating Channels”, dealer will update software. Approximately 30,157 vehicle affected. Have dealer confirm if VIN is included – MBUSA can also check here http://www.mbusa.com/mercedes/recall

Recall 2014120002 DEC14 2014-2015 212, 204.9 (GLK) & 2015 166 (ML) w/651 engine (4 cylinder diesel) chain tensioner sealing ring may exhibit increased settling behavior which could negatively influence pre-tensioning force, dealer will replace sealing ring. Approximately 4,314 vehicle affected. Owners of affected vehicles will receive a letter. Have dealer confirm if VIN is included, MBUSA can also check here http://www.mbusa.com/mercedes/recall

LI54.10-P-060515 DEC14 212, 207, 218 (B03) ECO start/start inoperative + message “Battery – Service Required” FC B21DF71 displayed, incorrect installation of accessories. Approved accessories must always be connected directly to ground points provided on the body in accordance with installation instructions. Work will not be invoiced under warranty or goodwill.

LI83.10-P-060403 DEC14 212, 204 w/code 581 noises from rear blower motor, check to see if cable set is properly installed.

WDDHF4HB7BA490616

Can someone give me the bulletins on this ? Specofivially I'd there was any camshaft or solenoid recall or problems .

Recall 2014120006 JAN15 – 2015 212 in the event of severe frontal crash for the rear middle passenger seat, double seat belt buckle may fail. Dealer will replace buckle. Approximately 1,378 vehicles affected.

LI91.10-P-060560 JAN15 –212 front seat belt buckle rubs on leather causing creaking noise, buckles must be lined with felt.

LI72.40-P-060689 JAN15 – 207 window operation nonfunctional, software error adjust parameters to door control unit.

Service Campaign 2012070002 may apply
https://mbworld.org/forums/e-class-w...ml#post5381790

In addition, and although not covered by campaign solenoid installed at production is replaced.

any bullintins or recalls for mine? VIN -WDDHF8JB7CA629968

Any idea of the VIN range for this W212 recall ?

Only documents model year, have dealer check VMI to see if your VIN is included.

For MBUSA members you can check here http://www.mbusa.com/mercedes/recall

Thanks for the link!!:y

According to the Press Release, this recall affects all W212 models built from Oct. 8/15 up to and including Oct.24/15.

Unless I missed it (and not disputing), here is bulletin.

Recall 2015020001 FEB15 – 2013-2015 212, 218 secondary rubber hood seal may not be secured properly. May temporarily adhere to engine hood and drop making contact with exhaust system should the catalytic converter be hot, there exists a potential risk of fire. Dealer will install additional retaining clips. Approximately 147,224 vehicles affected.

LI35.31-P-060795 FEB15 – 212 wagon as of 1/1/14 production rear axle howling noises 50-70 mph, replace rubber mounts to rear axle differential.

LI72.12-P-060888 FEB15 – 218 as of VIN A133492 up to A138257 rear window wet weather squeaking noises, replace inner sealing rail.

LI72.10-P-060913 FEB15 – 212 with Bang & Olufsen BeoSound AMG (code 811) creaking in area of mirror triangle, replace triangle cover.

Recall 2015030005 APR15 – 2012-2015 218 (CLS) rear side marker lamps may not illuminate according to specifications, dealer will SCN code rear SAM. Approximately 30,041 vehicles affected.

LI83.30-P-061224 APR15 – 212.095/098/298 (Hybrid) AC has insufficient output or none at all, replace HV battery. Refrigerant circuit shutoff valve at HV battery has hairline crack.

LI68.10-P-061068 MAR15 – 218 instrument cluster noise, dealer will apply felt to IC facade.

Engine Knock???
 

Quote: Konigstiger

LI03.10-P-052286 SEPT11 knocking noise from engine, inspect cylinder walls for scoring if found engine must be replaced. Affected vehicles are mostly production dates from 8/10 to 11/10 but might be outside this range situation was corrected as of engine # 2729xx 31932895 & 2739xx 30441186.


Dan, Could you possibly send to me the above mentioned TSB. I think my Engine #272980 31573692 may be experiencing that knock mentioned.
Any assistance would be helpful.
Thanks, Rich

LI82.61-P-061310 APR15 – 212 with Becker MAP PILOT (509 or 508) when vehicle is driven on an uneven surface or glove compartment is closed while MAP PILOT is in use, LVDS connection is reinitialized – message appears “Navigation is being activated. Please wait…” perform software update.

LI82.61-P-061420 MAY15 – 212, 218, 117,156,166,172,204,207, 242 with code 508 or 509 Becker MAP PILOT not recognized, fails to boot up, hangs up. Affected part # 1669008912 containing navigation module 1669009012 update interface and navigation software + firmware.

LI09.40-P-061542 MAY15 – All models with engine 276DELA (E400) rattling noise from the engine area under partial load, noise is normal. Valve disk of the wastegate in the turbocharger vibrates in the valve seat, when the wastegate is slightly open (partial load operation) and causes a rattling noise. The actuation of the wastegate can be changed via Xentry so that it remains closed for longer in partial load operation together with SCN coding of the engine control unit however, this change can lead to light hissing noises from the turbocharger.

Service Campaign 2015050005 JUN15 – 212 (e250), 166, 204.9 with 651 engine (4 cylinder diesel) replace timing chain tensioner sealing ring. Variations in material tolerances during certain production period could lead to loosening of the chain tensioner as well as an ineffective gasket seal for engine oil. Approximately 814 vehicles affected.

sub'd

Service Campaign 2015060006 JUN15 – 2015 212, 218 heat shield may have been installed by mistake on left side of engine leading to clearance condition, dealer will check/remove. Approximately 5 vehicles affected.

LI82.10-P-061580 JUN15 – 212 residue on interior of headlamp assembly plastic emissions produce transparent coating on headlamp lens, clean inside lens (no mention of LED).

LI07.04-P-061777 JUL15 – 212, 207, 218, 166, 221, and 251 with 642.8 engine changes to limp mode, absolute pressure sensor instead of a relative pressure sensor may have been installed. As of MY13 (code 803) absolute sensor is used.

LI82.85-P-061863 JUL15 – 212 with code 432 up to VIN B177740, 218 up to A153241 when multicontour seat button on the COMAND controller is operated central display switches itself off, replace controller.

LI54.30-P-061864 JUL15 – 212 as of VIN B085484 up to B177229, 218 as of A141977 up to A148184 assistance graphic can freeze if a Distronic speed is set and then immediately cancelled, perform control unit programming of instrument cluster.

Transmission not shifting?
 

Have noticed if I am going down an incline at 30 MPH for about 1/2 mile and then get on level streets, the transmission doesn't shift to a higher gear as it used to.
It seems that last time even when I used paddle shifters to shift up, the indicator showed a higher gear, but it didn't seem like it.
Have read that there are problems with the 722.9 NAG2 (7G-Tronic) transmissions, but not sure which I have. The Data Card shows 722906 02 473909 for a 2010 E350 with Oct. 2009 build date.
Haven't really noticed it in my other driving.
Thanks!

I'll add to this with a general observation that may, or may not, be relevant:

My experience is that the so-called "transmission learning" may not be helpful at all.

Over the 4.5 years of my 2011, I have on multiple occasions complained of hard (fear of damage) shifts when going up a gentle rise. No fault is ever found, of course, but usually the transmission is reset to default and the problem is gone. Then, over the months, the damn thing "learns" my driving and starts pounding the transmission again!!! I then go through the same cycle with service. I'm sure this would be different for each individual driver.

I wish I could get a reset and then turn off "learning!"

Service Campaign 2015080001 AUG15 – 2015 212, 218 rubber seal on top edge of the secondary bulkhead in engine compartment damaged by supplier during production, dealer will replace seal and four retaining clips. Approximately 209 vehicles affected.

LI54.10-p-062091 AUG15 - 212, 218, 207, 204, 172, 231 with code B03 (ECO start/stop) without 4U7 (voltage dip limiter) head unit display fails shortly after vehicle starts to move in addition, following fault messages may display: Release Parking Brake, ESP-Service Required. Check/replace backup battery coupling relay.

LI72.20-P-062120 AUG15 – 212.2 as of production 12/15/14 up to 3/31/15 noises from liftgate latch area, only closes to first latch position, Liftgate Open message in IC > 6 mph. Replace liftgate latch.

LI88.20-p-062054 SEPT15 – 218 wind noises at windshield between approximately 55-75 mph. Tape transition between surround and bumper if noise is gone, caused by airflow displacement parts are not expected to be available before NOV15.

Thanks Konigstiger.


My '14 E250 (40K miles) had the intermittent PB warning lamp issue, which I never seen, but the wife did a few times. Of course I blamed it on her touching the PB somehow. Anyway, my dealer did work on it and replaced the relay as indicated. Still testing this fixed, since it was an interment issue.


Interesting enough the service tech also has a '14 E350 which he also stated his wife noticed this issue, yet he never had. Guess we got to trust our wives a bit better when they tell us the strange happenings and gremblem's :smash:


LI54.10-p-062091 AUG15 - 212, 218, 207, 204, 172, 231 with code B03 (ECO start/stop) without 4U7 (voltage dip limiter) head unit display fails shortly after vehicle starts to move in addition, following fault messages may display: Release Parking Brake, ESP-Service Required. Check/replace backup battery coupling relay.

You are a great man:bow:!

:cheers:

Can someone tell me which bulletin covers the defective wood in a 2012 E550?

LI68.30-P-053962

:y^^^If we even meet drinks are on me

TSB
 

Can I have all w212 tsb?

Service Campaign 2015090006 OCT15 – 2015 218 (CLS) transmission control module does not correspond to current production configuration, dealer will update software. No mention of related symptoms. Approximately 115 vehicles affected.

Could you bring me up to speed on anything that effects my 2013 E350 4Matic? WDDHF8JB9DA670894.
Thank You

Thanks for the super fast reply!

LI82.85-P-062498 OCT15 – 2015 & 2016 207, 212, 218 disk plays from the beginning when COMAND (531) unit restarts instead of last point reached, update software.

LI82.60-P-062473 OCT15 – 2015 218 (CLS) Audio 20 head unit (1) Intermittent restart while driving, update software, (2) Partial startup/will not restart, replace head unit.

LI42.10-P-062555 NOV15 – 207 front brake juddering “complaint”, cause thickness of disk. Replace linings and disks.

LI42.10-P-062556 NOV15 – 207 rear brake juddering “complaint”, cause thickness of disk. Replace linings and disks.

Interesting
 

I had a couple of cars where the CD would go back to the start of current song when you started the car. That was nice as you did not start in the middle of a song.

Service Campaign 2015110001 NOV15 – 2015 & 2016 212, 218, 242 Audio 20 when saving 26th HD radio station logo head unit begins reset loop. Update control module software. Approximately 22,156 vehicles affected.

LI68.50-P-062299 NOV15 – 212 wagon, load compartment cover does not move upwards when tailgate is opened, magnet is integrated in right guide pin detected by sensor in guide rail. Check if magnet is installed (image shows magnet not present).

LI91.30-P-062537 NOV15 – 212 (w/designo equipment only) front seat heater wiring is visible, remedy is being developed optimized parts will be available shortly.

Recall 2015110006 DEC15 – 2014 212 incorrect fuel line installed, dealer will replace. Approximately 809 vehicles affected.

Service Campaign 2015120001 JAN16 – 2012-2014 117,166,172,204,207,212,216,221,231,251 fuel system control unit fault memory behavior may malfunction leading to incorrectly displayed diagnosis results or the inability to delete results, dealer will update CU software. Approximately 68,535 vehicles affected.

LI83.30-P-062887 DEC15 – 222/212/205 hybrid insufficient AC cooling output, perform leak test of refrigeration circuit of high voltage (HV) battery, replace HV battery.

Don't blast me!

I love this thread and really wish they had one in X204 section. I have a clunky upshift from 3-->4 on no/very little throttle on 2015 GLK350 with 7G Plus. Would love to take a TSB in to dealer - they claim all is well.

This is an awesome thread, I should subscribe and stay on top of these.

Does anyone know if the repairs for the service bulletins only apply during the initial warranty period? How about with MB extended warranty?

I will be checking with my dealer as well. They did replace free of charge two seat back shells on the driver and rear passenger seats that have cracked along the thread lines. That was on a 2011 last year (2015). The original warranty was expired and I was told the MB extended warranty we purchased did not cover it. They had to review it and agreed to replace free of charge which was very generous of them. The light grey mb-tex covers had to be shipped in from Germany as apparently there was none in stock anywhere in the US.

Great thread! Thanks for the info, just subscribed.

Could you let me know which service bulletins, campaigns and recalls affect my 2014 E350 4Matic? VIN WDDHF8JB6EA883898.

so far I only found: "LI62.25-P-056043 JUN13 – 212 & 218 deformation of engine compartment soundproofing due to water ingress. Install optimized seal part # 2126280800" Like others have said, looks like someone took a picture of my engine bay.

Thank You

Very odd that I just had this recall item fixed at MB yesterday. I'm surprised previous owner never had it done since it seems to be quite old. I luckily went to have my trans service done and they told me this was an open recall that they'd fix for free. I guess he avoided going to the dealership for repairs etc.

LI27.20-P-063110 JAN16 – 278 up to MY14 after a shift is performed under medium load a slight shudder is felt, low slip speed of torque converter lockup clutch allows engine firing order to be felt through driveline. Update software. Vehicles MY15 and newer have been produced with the software solution.

Brake juddering/shuddering felt when braking, replace linings & discs:

LI42.10-P-063149 JAN16 218.391 (cls500 4matic) rear
LI42.10-P-063150 front

LI42.10-P-063151 JAN16 – 212.091 (e550 4matic) rear
LI42.10-P-063152 front

LI42.10-P-063153 JAN16 – 212/218 (sport 951) rear
LI42.10-P-063154 front

LI42.10-P-063156 JAN16 – 212/218 w/brake dimensions 300x22 mm rear

LI42.10-P-063155 JAN16 – 212 w/brake dimensions 344x32 mm front

LI42.10-P-063157 JAN16 – 212 w/brake dimensions 320x24 mm rear

LI77.00-P-063147 JAN16 – 207 Cabrio chirping/rubbing type noise just before roof fully closes, seal in affected areas and Insert filler foam into seal channel (see photos).

:y

great thread!

Service Campaign 2016010006 FEB1 – 2015 212 digital Owner’s Manual may not be loaded & CD-ROM not present dealer will load & supply CD. Approximately 622 vehicles affected.

LI91.10-P-063385 FEB16 – all models front drive & passenger seat creaking/grunting when pressure applied to backrest, tighten 4 bolts of seat height adjuster to 50 Nm torque.

LI91.10-P-063393 FEB16 – 117, 156 before VIN A27110 on 212, 166, 172, 204, x204, 246 splitting of seat, replace as needed (see below).

LI82.85-P-063619 MAR16 – 212, 218, 117, 156, 176, 207, 242, 246, 292 w/code 531 COMAND displays 2035 date, internet radio inoperative, and/or free browsing inoperative, remedy is being prepared in the meantime can be rectified by resetting COMAND date via Xentry.

Thanks a lot kingtiger!
Im new to bulletins and cant determine how it works.

I have splitting in my seat in my car (WDD2120031 A080969), just as LI91.10-P-063393

Would my car be covered then?

Thanks

Xentry bulletins are only covered under warranty i.e.: initial factory or extended. However, in this case as it applies to your 212 because the bulletin documents a known problem (defect) within a specific VIN range “before A27110”. Since A080969 is within range reference bulletin to service manager and request he/she contact MB to see if they will approve goodwill assistance unless you have a MB extended warranty then it should be covered.

Note, no reference to leather or MBtex surface therefore as it currently reads it should apply to both.

It is? How do you read the VIN? Isn't it the last six digits of the the VIN? Shouldn't that be A027110? I'm confused :nix:

I was thinking A271100 :nix:

To Konigstiger,
Since upgrading to Win10, I can no longer get access to EPC to pull up my Data Card. Something to do with Java and Edge and IE11?

Would you be kind enough and look up my Data Card for:
WDDHF8JB2EA821673

Thank you in advance.

Certainly.

Thanks Dan!

I've seen your name here since I bought my first Benz in 2003 and now I'm on my third and all is wanna say is Thanks Konigstiger for all your insight. Question for you ,how can I turn my avatar right side up??

Move from Jersey :D - plenty of relatives there Middletown, Jackson. Matawan, Manalapan… Anyway, image needs to be right before downloading to profile.

Be kind Dan:) Long Branch and the area you mentioned were my old stomping grounds before moving to South Jersey. Yeah, I'm one of those 609'ers.

Intelligent ,knowledgeable and a sense of humor too......LOL

LI80.35-P-063677 - All models Keyless-Go DAS4 (2007 >) “Replace battery in transmitter key” reappears in instrument cluster within a few days after replacement, update KG control unit software/perform SCN coding. FYI if key enters passive mode resulting in no feedback from key during KG engine start key can be reset by removing battery.

LI00.20-P-063991 MAY16 – 2012 212, 207 service display prompt shows same service (A or B) twice in succession, update instrument cluster.

Mercedes Hard to Find Parts .. Cheap!!
 

This is the best Website for those hard to find parts!!

www.myrecycledparts.com

Service Campaign 2016050001 MAY16 – 2016 207 Cabriolet A-pillar seam may allow moisture ingress, dealer will seal. Approximately 415 vehicles affected.

LI82.60-P-064266 JUN16 – 212/218 with Audio 20 (505, 520, or 522) switches itself off and on without cause & telephone menu cannot be activated, flash headunit and SCN code.

LI09.40-P-064267 JUN16 – 651 engine rattling noise from front of engine on left in area of turbocharger for a short time after cold start, replace air duct housing.

Konigstiger,

Would any of the TSB's you mentioned above apply to a 2012 E550 4matic regarding the "Brake juddering/shuddering felt when braking, replace linings & discs"?

063151 & 063152, check your PM.

LI46.20-P-064605 AUG16 – 212 left hand drive except 4matic without direct steering (211) up to VIN A659000, play in steering about center position. Has no effect on steering vehicle. Possible wear between pinion and steering rack, replace control head of steering.

LI54.10-P-064674 AUG16 – 212, 218, 207, 204 with start/stop (B03) production 12/2011 to 3/2012. Engine does not start / selector sticks in “P” and/or fault messages on driver assistance system, replace prefuse box F32.

How do you check for this play? There always seems to be a bit of play around center. Is there a guideline for it? And if the car is out of warranty does it become a time and materials job?

No details. Out of warranty, at cost repair.

Hello Konigstiger

You gave me some advice some months back as regards my 2010 E350 tranny, i am back with thesame problem again. Transmission still do a automatic P' mode at a speed less than 6km each time i slow down. I did a tranny flush and tranny reset couple of times like you suggested. My Technician had to take the valve body out today and check the solenoids/valves. Same problem still persist.
what is the likely problem? what do you suggest.

Best regards

P.S error codes is never stored on the system memory

Help with data card
 

Konigstiger:
I purchased my CPO 2010 E350 coupe from a M-B dealer, but the owners manual was missing and I received no data card - only what the dealer listed on their used car sticker. The dealer ordered an owners manual for me, but I did not the full data card information.

I would appreciate it if you could check and PM me the data card for WDDKJ5GB0AF018626.

Thanks in advance.

LI82.10-P-064766 AUG16 – 212, 207, 218 (halogen code 614,615,616,618,621,622) headlamps fogged or droplets forming, due to the vent openings lamp unit is an open system meaning moisture dirt, etc. can penetrate resulting in deposits in diffuser and lens. Fogging does not impair the functionality or the service life of the lamp unit. Check housing cover. See PDF attachment + images below.

Service Campaign 2016050009 SEPT16 – 2016-2017 207, 172, 231, 217 air scarf function may have been deactivated, dealer will check electrical connectors. Approximately 534 vehicles affected.\

LI08.30-P-064799 SEPT16 – 222, 212, 205 hybrid AC inoperative no hybrid functions active until next ignition cycle, engine control module or powertrain control unit must be updated to latest software. Replacing battery does not remedy problem. 222 OK since 5/5/14/16 (VIN A277932), 212 5/31/15 (B214096), 205 5/14/16 (F400240).

Konigstiger: Great job here, just got the wife a 2014 E350 4matic. Not bad price mid 30K with only 27K miles CPO. I'm sure they checked for recalls but can you check my vin or get a "data card" whatever that is. thanks so much. bob WDDHF8JB4EA915814

Here’s the data card. You can check recalls here: https://www.mbusa.com/mercedes/recall

Greetings Konigstiger,

Maybe you can help me with your wisdom. I want to change the factory springs to H & R s, however the sellers only list it for a E 350 and says it will not fit the E 250. My question is aren't both setups the same as far as the springs and shocks ? Thanks in advance.

Check with H&R direct: H&R Special Springs 888-827-8881

I spoke with them and they cannot verify that it will work because they have never fitted on a E 250, is there a way to find out the part # for the springs for a 350 and 250 with sports package? If the factory springs are the same then it will work.

Cross reference OEM part #s front 2123211404, rear 2123240404 also applicable to e350 see attachments.

LI82.85-P-065110 OCT16 – 207, 212, 218, 213 (code 522) Garmin Map Pilot navigation update using download manager may trigger another execution of test routine causing message “connect SD card to vehicle”, consent to connect SD card.

Parking lights activating unintentionally
 

Took my car in and had them check to find out why passenger side parking lights came on by themselves twice in past year and once in year before. They ran an Xentry check and everything was normal.
However, I found on another site (True Delta) that there is an 08/29/14 TSB re: electrical and air conditind; "damaged ESC of driver circuitry side marker output."
Anyone know the TSB number because this sounds like my problem.

Too little info to pursue True Delta bulletin. I attached sheet so that you may better understand parking lights actuation and function.

Thank you
 

Thank you and I took the information you sent me a couple of weeks ago by PM to the dealership. SA printed out the XENTRY Final quick test log. Everything checked normal, including front and rear SAM's. Did have a few (!) due to "ECU not available" but those are for Sat radio, media interface, etc. that I don't use. SA said didn't really mean anything.
I do understand the parking lights system and have never turned them on. Lights stay on Auto, except very few times I actually turn on the headlights so I can activate the fog lights. Then I make sure switch is back on Auto.
Tru Delta said they got info from NHTSA and I went to their website for recalls and TSB's (AKA Manufacturer Communications). Couldn't find the TSB above.
Thanks again. At least I have it documented on work order that their is a complaint.

Recall 2016110008 DEC16 - E-Class Coupe & Cabriolet (207) may have been equipped with an underbody panel that may not provide sufficient clearance to left catalyst. Dealer will check and replace. Approximately 814 vehicle affected.

Hi konigstiger,

I have a question about the DTB P-B-54.70/218 bulletin. As far as I understood it was released on May of 2009. Does it mean that the cars produced later, 2013 E class for example, already have the latest software?

Erroneous warning happened to me 1-2 times when moving along the barrier. It also gave false warnings in rainy/snowy days. I took the car to the dealer and referenced to the service bulletin above. They said that they couldn't reproduce the error and that since my car is 2013, it already should have the latest software. Is that even true?

Thanks.

No matter malfunction could not be reproduced, dealer should still check for updates and confirm software is current then document this on your invoice.

Hm, the dealer calls itself "a 5 star dealership", but I hate when they say "we couldn't reproduce." I had the speedometer needle not working. It wouldn't move intermittently. I took it to the dealer and they said that they couldn't reproduce. I had to capture it on a video and go back to them the next day. Now they have ordered a new one for me. It is coming from Germany so will take some time.

I think the service bulletin you posted said "to flash the SGR". The dealer said that SGR was for the distronic which my car doesn't have.

Any advise on how to ask them to check for the latest software is appreciated. I asked to check for Comand update once - they didn't.

Check PM.

Recall Campaign 2017020021 FEB17 – 2017 213, 117, 156, 205, 253 starting current limiter (SCL) could be overloaded worst case scenario components can melt and ignite, dealer will replace SCL. Approximately 24030 vehicles affected.

LI82.95-P-065703 FEB17 – 213 remote start is not executed “Side window or sliding sunroof not fully closed”, update software to all four door control units.

LI82.85-P-065716 FEB17 – 213 with command NTG 5/5.5 (code 531) language of digital operator manual automatically changes, install newer version part # 2138276300 or successor.

LI68.40-P-065763 FEB17 – 213 non-AMG inside rear view mirror shakes or vibrates, install damper (see image below).

Hi Konigstiger, I was wondering if you could provide my data card? My VIN is WDDHF5KB6EA890525. Thank you in advance!

9/4/13

Now I have a question. I see that I have option code 258 "collison warning system with active brake interv fcw stop". I take that to mean that basically it has autonomous braking where the car will brake itself. I thought that all I had was where you just get the red light flashing and a warning beep. Are you telling me that the car will automatically apply the brakes?

See capture.

Question about this post for brake shuddering
 

Is this saying there is an open recall or campaign on this? Or just a known issue? I ask because my car has the shuddering brakes issue; the brake disks were replaced about a year ago, and the issue has returned. So I'm facing the replacement of a second set of rear disks within one year.

12 e5504m see attachments for current part #s compare to invoice parts #(s) installed. Not recall or service campaign but rather MB bulletins covered under factory warranty (aside from 1 year/12,000 mile MB brake warranty), dependent on wear in your situation you "may" be able to successfully argue no cost disc/pad replacement referencing MBUSA 12 month/unlimited part warranty if within this period - dealer may refuse, contact MB 800-367-6372.

It works! I once took my eyes off the road at the wrong moment (coming over a hill) and caught up with a tailback. The car yanked my seatbelt tight and hit the brakes just a tiny fraction of a second before I did. My front bumper ended up about 18 inches from the last car stopped in the roadway (stopping with full braking on dry pavement). My input probably helped, because I believe the auto-braking is a percentage of full braking, but the system definitely beat me to the pedal and got the braking started a fraction of a second sooner. When you are talking 55 mph (88.5 kph) and 18 inches (46 cm), fractions of a second count. If I had been asleep, drunk, or having a heart attack, I'd have hit that car, but I would have been going a LOT slower than without the collision avoidance system.

Service Campaign 2017030011 MAR17 – 2005-2014 212, 207, 204, 203, 197, and 171 Takata defect decision, dealer will replace driver & front passenger airbag. Approximately 540 vehicles are involved.

Hello Mr. Konigstiger, would you be able to provide my data card? My VIN is WDDHF5KB4EA996715 Thank You.

“Mr. Konigstiger” ... fitting for an aristocrat :eek: :D

Mr Konigstiger...I just got a new to me 2011 E550 with only 18K miles. WDDHF7CB3BA421818 and today i just noticed that the passanger seat is not straight. It is calked of to the left a bit. Everything works as far as adjusting the seat. I'ts not straight like the driver side. The track looks like it takes a slight different angle than the drivers side... Wierd!!


Was there ever any bulletin about this? Thank you for all you do for everybody!

Reference LI91.10-P-054143 “adjustment is biased to one side which bends the seat frame”.

Thank You Very Much Mr. Konigstiger!!

Recall Campaign 2017030015 APR17 - 2006 through 2016 117, 164, 166, 190, 204, 205, 207, 211, 212, 218, 221, 222, 231, 253, and 463 vehicles that received a control module coding update while at dealer between December 3, 2016 and December 5, 2016 might not function as intended dealer will update the affected control modules.

Hi Mr. Konigstiger...


My Tranny started acting up today. I took off and it didnt want to shift. stayed in 3rd. After a mile or so it starte working fine. Got out of my car to go to the store...got back in and it did the same thing for a mile or so then started to shift normally.


Also first thing in the morning I start the car put it in D, step on the gas... and there's a little jerk then all is good. It doesnt happen but in the morning when the motor tranny is stone cold.


Can you please give me your opinion? 2011 E550 with only 21,000 miles...

Have independent or dealer check for fault codes using MB diagnostic system.

Hi,

Would it be possible to look up VIN: WDD2120742B211409

Thanks in advance,

Carl.

Certainly.

Thank you :).

With 23K on the clock on a CPO car I bought with 17K on the clock after which I had almost immediately complained about brake pulsing, my dealer refused to try to get MB to replace them because the car was 3 years old. Then told me they would fix my fronts for $800-900.

Hi konigstiger,

Is that saying that Collision Prevention Assist is a sub function of Distronic Plus? I don't have option code 258 on my data card, but I have codes 233, 266, 271, and 300 (which all reference some form of autonomous driving/braking). My CPA doesn't seem to be working, as I never get a warning beep or anything, no matter how close I get to the car behind me (unlike other cars I have driven, I get the warning beeps). I don't even have the CPA menu in the dash options. The dealer says it is part of Distrionic and it's "working normal". How do they know it's working fine, if the thing doesn't even work. :nix:

Good afternoon,

Can I please get one for VIN: WDDHF8JB2DA717313

I was just gifted this car but have no idea what all it has.

Thank you!

10/10/12

Recall campaign 2017040007 May17 – 2017 207 propellant mix ratio in pelvic airbag igniter might not meet specifications, dealer will replace airbag. Approximately 255 vehicles affected.

ooops, duplicate post.

LI54.65-P-066284 MAY17 – Vehicles with reversing camera (code 218) or 360 camera (501), see attachment.

Datacard in english
 

Please send me data card for my car.
Wdd2073471f027667

Thanks in advance.

Kåre Hedlund

Here you go.

Took to the Dealer, they did the latest software update...and the car runs awesome...


thank you so much.

Hi Konigstiger, I was wondering if you could provide my data card? My VIN is WDDHF8JB2EB058600. Thank you in advance!

7/4/14

Thank you:slap:

LI82.85-P-066702 JUL17 – 212, 218, 207, 117, 156, 166, 172, 176, 242, 246, 292 NTG 5.1 with codes 522 or 357; 205, 253 NTG 5.2 with codes 355 or 357; 213 NTG 5.5 with code 522 and 355 or 357 Garmin MAP PILOT traffic information and possibly voice control inoperative using download manager 2.0.29 or 2.0.30, run recovery function and reinstall navigation software update.

LI82.70-P-066767 JUL17 – 212, 218, 207, 117, 156, 166, 242, 246, and 292 with code 531 some contacts on telephone via Bluetooth are not found via voice control contacts can be selected manually using rotary pushbutton, update COMAND software.

LI82.85-P-066769 JUL17 – 2013 through 2016 212, 218, 207, 117, 156, 166, 172, 176, 204, 231, 246 with codes 512, 514, 527 and 803, 804, 805, 806; 463 XZ2-6 after map update is aborted navigation no longer functions, delete map data via Xentry diagnostics: special procedures tab – navigation data (hard drive) – erase data and update COMAND.

Hi Konigstiger,

can I get the datacard for WDDHH8JB6GB299363?

Thanks.

So far my car hasn't had a recall but it's still early. :)

11/11/15

Thanks Konigstiger. A lot of stuff on the car I didn't know about and a lot of stuff I don't know what it is.

1U2 SNOW GRID

6P5 STEUERCODE VERTRIEB FUER CODE 475 ANFORDERUNG

N5A STEUERCODE W50 FUER PPS-INT. VERWENDUNG

Please send me DATA CARD

VIN: WDDHF5KB7EA865794

7/25/13

IU2 = A/C air intake is equipped with a screen which prevents snow and other debris from entering
6P5 = control codes for TPM (tire pressure monitor)
N5A = control codes for PPS (pedestrian protection system)

Hi konigstiger.

Thanks for doing this for us!

I'd like to see my data card as well.

Previous searches show 432 Dynamics seat, front left and right.

Dealership states only the drivers side is so optioned and that MB USA will not provide coding for retrofit.

Could it be this option is already coded?

VIN: WDDHF9AB5AA143534

Hi Konigstiger,

While I own a E250, just purchased used a GLK250 and looking for the data card for this GLK.

I would appreciate a data card also. My VIN is WDCGG0EB3FG435254.

Thank you in advance!

Here you go.

Thank You Sir! Dealership cant confirm passenger seat coding. Line 432 seems to indicate both right and left Dynamic seats. Not sure if all W212s with dynamic seats shows both sides on their data cards.

Datacard & brochure show left/right however, 212 intro shows “driver seat”, EPC shows dynamic left seat only see attachments.

Thank You for this useful information! Looks like the coding is unavailable in the US. It'd be a great retrofit though!

Recall 201612005 MAY17? – 2013-2016 222, 207, 212, 231 electric power steering control module might have improperly soldered contacts steering may deactivate, dealer will replace steering rack. Approximately 70 vehicles affected.

thanks Konigstiger.

I would appreciate a data card for VIN: WDDKJ5GB9AF040706
Thanl You

2/16/10

Hi @Konigstiger, after some searching time, I was able to find my "new" S212, but I would like to know the full equipment she has.
Would it be possible to send me the Data card?

VIN: WDD2122941A934744

Thank you very much in advance.

11/20/13

Many many thanks :)

Service Campaign 2017120002 JAN18 – 2009-2013 212,164,251 fuel injectors may not meet current specifications, dealer will replace injectors. Approximately 17 vehicles affected.

Recall Campaign 2017120024 JAN18 – 2012-2017 212, 207, 204 steering column adjustment insufficient electrical grounding in column components, dealer will correct grounding and install protective ring to steering column module. Approximately 5,165 vehicles affected.

Service Campaign 2017090009 JAN18 – 2016 117, 218, 212, 207, 463, 166, 156, 292, 172 engine control module in the event of a faulty fuel tank level sensor CEL might not activate, dealer will update ECM software. Approximately 138,674 vehicles affected.

I would appreciate a data card for VIN: WDDHF8JB0FB135059

A Cardinal Red Beauty, I love that no one else has this car on raod, you never see red ones!!!

Started with a 1985ish 300D turbo diesel , on our forth.

Thanl You

12/4/14

I would appreciate a data card for VIN: WDD2120821A894798.

Many many thanks https://mbworld.org/forums/images/smilies/smile.gif

9/11/13

Thank you very much.

Hi Konigstiger! I have been away for a loooong time, but was thrilled when I logged on to see you are still active on this forum. You have always been such great help.
My 2011 e350's Command control knob next to the center console armrest does not work correctly anymore. One night it just stopped having the ability to function by rotating it left or right.
Can you please let me know if I missed a recall or what your professional opinion may suggest?
Many thanks.
Brian

Known/common problem but unfortunately MB has not addressed the matter, no bulletins. DIY repair: https://mbworld.org/forums/e-class-w...mand-knob.html alternative replace unit (about $190 or so) PM VIN if you want part # to comparison shop.

Many thanks, your help is very much appreciated!VIN #WDDHF8HB9BA268490

https://cimg1.ibsrv.net/gimg/www.mbw...35eef30b2d.jpg

$192.32 https://www.parts.com/
$197.23 https://www.mbdirectparts.com/

Thanks Kon....

Perfect...thanks for spending the time to help us out. Much appreciated :urock:.

Hi Konigstiger and everyone

I am new to the forum, I have just recently purchase my 2012 W212 E350 Avantgarde with CPO (45,000Km). I have recently notice that at low speed the steering wheel makes what I can best describe (from another similar thread) a whipping sound (not creaking or groaning noise), somewhat faint to hear it, I have to turn off the radio to be able to hear it. A member here mentioned in that thread that "its normal", can you please share some light as to why it is or it isnt normal?

Does anyone one else has ever come across this or experience this? I own a W220 S-Class and it never makes such noise.

Thanks in advance.

Michael

Are you referring to similar issue by any chance?
https://mbworld.org/forums/e-class-w...r-estimat.html

Your issue might be different, but I experienced something similar with my 2013 E550 which is the the W212 body style. Below is the excerpt from the dealer invoice (thanks God was covered by the ELW)

Cause: STEERING SHAFT BOOT AND BEARINGS
Correction: ROAD TESTED VEHICLE, CONFIRMED SQUEAKING NOISE FORM STEERING SHAFT AT FIREWALL AREA. REMOVED UPPER STEERING SHAFT FROM STEERING COLUMN. R&R REAR LOWER ENGINE PANEL. REMOVED UPPER STEERING SHAFT FROM LOWER STEERING SHAFT.
REPLACED UPPERSTEERING SHAFT BOOT THROUGH FIREWALL AND BOTH
BEARINGS.REASSEMBLED, NOISE GONE.

Service Campaign 2018020005 FEB18 – 2015 & 2016 207, 212 engine control unit does not correspond to current production configuration, dealer will perform SCN coding. Approximately 10,897 vehicles affected.

Hi Rovel,

Exactly what the dealer diagnosed and did as well. Thank goodness that I also have extended warranty.
Does anyone know if there was ever a bulletin regarding this matter?

Michael.

What do these characters correspond to? Is this info I should provide to my service writer if this is an issue with my vehicle? Will it be covered by the manufacturer/dealer?

WHAT NOW?
 

Normally bulletins are only covered under factor and/or extended warranty at no cost. In your case software updates correct known production flaws contact MBUSA direct to request no cost goodwill repairs 800-367-6372 referencing bulletins numbers afterward print attachments to show SA.

How can I find out if this pertains to my vin # ( WDDHF5KB9GB203261) ?? I do my own required maintenance. Perhaps there is a web page where I can inquire?

Dealer needs to check VMI.

LI46.10-P-067941 MAR18 – 212, 204, 207 steering wheel area grinding and/or clicking noises, contact bridge may grind on the steering column switch module.

konigstiger, please review this thread (link below). Is there a service bulletin for overheated Anti-Theft Alarm LED that marrs the finish in the dash when the light fails? If it happened to mine, I imagine it has hit others, too. 2016 E-350... Thanks so much...

https://mbworld.org/forums/e-class-w...-bulletin.html

.

Not aware of any bulletin request switch block (upper control panel) be replaced under warranty. EPC documents original UPC installed at production is replaced.

https://cimg4.ibsrv.net/gimg/www.mbw...1427c22d90.jpg

Delete.

Does anyone know if there has been an update to this issue yet? Have they found a cause / solution?

My 2011 E550 does this every so often. It only runs for about a minute or two then resumes normal operation. This is maybe just normal updating, but it seems to happen oftener than any normal channel changes.

My 2014 car has over 180k miles, so warranty is long gone, but reading about all those extended warranties on emission parts, anybody has experience how it looks on ULEV cars?
I have to spend $2500 on new DPF for my Bluetec, what comes with over >2 months wait for rebuild to come from Germany.
I have MI showing DPF replaced 60k miles ago , so something is very wrong with this situation and having "the brick" occupying my garage for 2 months is not making me happy. Even I am happy with it when it drives ;)

Cannot find 2014 service warranty with e250BT here is a 2013 copy (e350BT) DEF warranty is 8 years/80,000 miles. To the best of my knowledge no extended warranty.

Thanks. Knowing what to look for, I was able to find one for 2014 as well.
Seems only PZEV vehicles do have 10 years/150,000 miles warranty on emission parts.
Mine is ULEV and looks like 250 Bluetec was never PZEV.
Funny to observe maze of laws. What was in past called "California smog requirements" now is observed in 7 (?) states and the number keeps growing.
Meaning in any calendar year you can have E class build with at least 4 different smog requirements.

Yes found that also however, as mentioned e250BT in not listed.

Recall Campaign 2018080015 SEPT18 – 2018 238 E-Class Cabriolet ISOFIX cross-member for child seats may not have been mounted according to current production specification, dealer will replace. Approximately 39 vehicle affected.

Service Campaign 2017120010 AUG18 – 2017 & 2018 213, 253 (GLC) front air suspension struts may not meet current production specifications, dealer will replace. Approximately 1,339 vehicles affected.

LI46.35-P-068762 SEPT18 – 213 up to VIN A048221 scraping or squeaking noises when steering from lock to lock, replace electric steering.

Request for data card
 

Konigstiger. Many thanks for the very informative posts that you make here. Please post data card for VIN WDDHF5KBXGB241680

7/16/15

Thank you
 

The data sheet should come with a decoder ring!

Invalid VIN recheck, search this thread for “AMG”.

4/12/2012

Recall 2018100010 OCT18 – 212, 164, 251 replace driver side airbag have dealer check VMI to see if VIN is included. Approximately 18,334 vehicles involved.

Service Campaign 2018110006 DEC18 – 2015 212, 204, x204, 166 fault in the fuel tank diagnostic software could lead to an incorrect activation of the CEL dealer will update ECU software. Approximately 47,546 vehicles affected.

Recall Campaign 2018120012 DEC18 – 2010 & 2011 212, 164, 251 Takata front driver side airbag, dealer will replace the front driver-side airbag on the affected vehicles. Approximately 24,602 vehicles affected.

Hi Konigstiger,
I recently bought a 2014 E350 4matic in October and it has a rubbing/grinding noise that comes from the right front end when I back up, I thought it was a clearance issue with the tires but my husband says the tire isn't touching anything when I turn. It has gradually gotten worse over the past 2 months so I'm not sure what it could be from. Do you have any ideas on what it could be from? Also could you please get the data card from my vin: WDDHF8JB7EA981175.
Thank you sooooooo much!

Visual inspection brakes, steering knuckle, axle for grinding noise.

Thank you so much!!! So it doesn't happen when I press on the brakes at all, its only when I turn a certain way and only in reverse. If there was something wrong with the brakes would it make noise when I pressed them? That may of been a stupid question but I'm clueless lol. I appreciate your help & input very much!!

Need to check complete area, keep in mind brake components can shift in reverse.

Hi Konigstiger, really cool how on top of things you are! May I put in a request for the Data Card for my machine? VIN: WDDLJ9BB5FA156055.

Thank you very much for the courtesy!

Bill

Certainly.

Hot Dog! Thank you very much!

Hi Konigstiger, thank you again for the Data Card for my CLS. Dumb question for you if I can? There are multiple items in the data card which aren't accurate for my vehicle, such as it isn't an AMG, it doesn't have designo leather, or has parking pilot (Code 235) to name a few. Would it be safe to say that a Data Card should be taken with a grain of salt?

I do have to say that I was impressed to see that my recent Smartphone Integration addition (Code 14U) was present in the Data Cara, Its nice to see this is a live document!

Thank you much for the dumb question.... Cheers!

Interesting, data card is almost always accurate. I would suggest visiting MB dealership to have them compare data card to their available info.

data card
 

Hi Konigstiger, I did just that... I found similar discrepancies which was my motivator to ask you for the courtesy of a Data Card. As you can see, there are some differences from your Data Card and the Master Inquiry..

I appreciate your help, I guess it'll be a mystery...

Bill

Speak with Service Manager requesting VEDOC confirmation/correction concerning data card & VMI discrepancies.

https://cimg8.ibsrv.net/gimg/www.mbw...e3e4efec1d.jpg

ECU software warranty is extended to 10 years / 120,000 miles, see attachment.

https://cimg3.ibsrv.net/gimg/www.mbw...e889fc9dc9.jpg

I will give it a shot. Thank you very much for the advice!

b

I just purchased a 2012 E550 and the wood trim is terribly faded. It does not match the VIN range(WDDHF9BB4CA637501), but it very obvious that this is the issue as the wood is almost "blond" in some places. What are my chances of having MB replace my trim?

Thanks in advance,
Scott

Assume you didn’t purchase from MB dealer. Email CAC include VIN, attach photos of trim faded worst, and bulletin requesting goodwill replacement due to defective trim installed at production: http://mercedes-benz.custhelp.com/ap...J1YUNhbw%3D%3D

No, I did not, I purchased from Audi of Lafayette(next door to MB...lol). It was a one owner car though, so hopefully that will help...

Thanks again. I'll email CAC

konigstiger, would you be able to provide me data sheet for VIN: WDDHF5KB0CA589830

Thanks!

1/11/12

Random question, I see in some of the service bulletins the models are specified, and those with 4Matic are sometime called out separately. If a model is called out but not its 4Matic variant, should I assume the 4Matic version is not affected/covered by the recall? Or should I assume the opposite?

Depends on subject for the most part bulletins affect all model variants referenced unless there is a 4matic note e.g.: “except 4matic”, “212 4matic”, “+ 4matic”

Service Campaign 2019040001 APR19 – 2012-2014 117, 166, 172, 204, 207, 212, 216, 218, 221, 222, 231, 251, 463 ECU Malfunction Indicator Light displayed while no fault is present in the control unit, dealer will update ECU software. Approximately 210,440 vehicles are affected.

Hi Konigster,

All these bulletins , do they cover only USA MB cars, or also global market ?

Thanks

North America but I see no reason for not referencing them in any market, best to produce a copy.

thank u K

Hi Konigster

Could you provide me with a Data Card for WDDKK7CF1BF061438

Thanks !!