Has anyone taken delivery lately?
#51
MBWorld Fanatic!
Wow! Looks exactly like my factory magno night black + trail package G
Mine is also in the shop getting PPF'ed - found someone in the LA area to do XPEL stealth for $5800 including the tire carrier in normal XPEL (along with mirrors, other normal areas of the car etc). Have had some problems with the installer in the past (uneven film edges, lifting and they have already been blasted for a botched wrap on a famous youtuber's previous generation G a couple years ago), but they mostly do dealership work for O'Gara and Ferrari so hoping they've gotten better with time...picking up the car tomorrow. My installer also used the pre-cut film where it just goes around the "V8 Biturbo" emblems, so hopefully it doesn't lift. Not sure what they did with the badges on the back...
Mine is also in the shop getting PPF'ed - found someone in the LA area to do XPEL stealth for $5800 including the tire carrier in normal XPEL (along with mirrors, other normal areas of the car etc). Have had some problems with the installer in the past (uneven film edges, lifting and they have already been blasted for a botched wrap on a famous youtuber's previous generation G a couple years ago), but they mostly do dealership work for O'Gara and Ferrari so hoping they've gotten better with time...picking up the car tomorrow. My installer also used the pre-cut film where it just goes around the "V8 Biturbo" emblems, so hopefully it doesn't lift. Not sure what they did with the badges on the back...
The following users liked this post:
Bexlee (06-02-2020)
#52
MBWorld Fanatic!
It’s in philly getting ppf’d. They’re starting to lock down areas in PA. I hope it gets finished before they quarantine the area and my car is trapped. My work is also putting everyone on backup call even when we’re post call and asking us not to leave tricounty area in the event that SHTF.
Here is one from the PPF shop.
Here is one from the PPF shop.
What areas of the G are you XPEL PPFing?
Is he taking anything apart to wrap the edges or using the 3d printer templates that go to the edges?
What is the approximate cost?
Thanks.
Last edited by JSwan724; 04-18-2020 at 08:33 AM.
The following 2 users liked this post by JSwan724:
Bexlee (06-02-2020),
Telly Bettis (04-19-2020)
#53
Member
The car was wrapped by Keyvon at ACAP Films Main Line outside of Philadelphia. They came highly recommended from the dealer and my detailer. In the past I used a closer installer but decided to use a "higher end" installer based on the fact that he's wrapped a few new FGT's and Chiron's. The complete wrap was 9k in xpel stealth. The wrap is AWFUL. The truck has been back for once repair and it is still not fixed. The doors are rattling because he didn't reassemble the door panels correctly. This work is absolute garbage. There are uneven edges, areas not pushed down, and areas that look like they ripped the film instead of cutting it. There are also wrinkles at the edges. I emailed Xpel and they basically responded with "Its an installer issue" and good luck to you. This is fifth and last car I will wrap with Xpel. I may switch back to 3m or Suntec. When I asked why it looks like ****, the answer was that "Xpel stealth is hard to work with and that the G63 is the hardest car to wrap in the industry". If this isn't fixed I'm going to be the squeaky wheel on their instagram, facebook, yelp and google pages warning others.
The following users liked this post:
Bexlee (06-02-2020)
#54
MBWorld Fanatic!
iTrader: (1)
Join Date: Dec 2019
Location: Marineland FL
Posts: 2,167
Likes: 0
Received 462 Likes
on
377 Posts
'25 EQG deposit, '21 718 Spyder & '20 HD Fatboy
I have Suntek on my Porsche and plan to use the same on my G when it arrives. My installer is top notch and he uses the patterns, which wrapped edges on my car so don't be deterred from an installer that uses those as opposed to custom cut pieces. There are several excellent installers on Rennlist that also use the templates and they all say the same.
The following users liked this post:
Bexlee (06-02-2020)
#55
Member
I have Suntek on my Porsche and plan to use the same on my G when it arrives. My installer is top notch and he uses the patterns, which wrapped edges on my car so don't be deterred from an installer that uses those as opposed to custom cut pieces. There are several excellent installers on Rennlist that also use the templates and they all say the same.
The following users liked this post:
Bexlee (06-02-2020)
#56
MBWorld Fanatic!
iTrader: (1)
Join Date: Dec 2019
Location: Marineland FL
Posts: 2,167
Likes: 0
Received 462 Likes
on
377 Posts
'25 EQG deposit, '21 718 Spyder & '20 HD Fatboy
I had Xpel on my Porsches, RR's and other cars with excellent results. It was my mistake to listen to others advice on the new installer. This was a preferred installer (which Xpel even recommends). The issue isn't the film- its an installer issue and Xpel's lack of customer support.
#58
Member
Join Date: Jan 2020
Location: West Yorkshire, UK.
Posts: 200
Received 57 Likes
on
30 Posts
G350d, Rover Mini , Abarth 500, G230, RS4
G350d at Zeebrugge today according to my dealer.
Woohooo!!!!
This car had an original build date 13April. Is anybody else likely to have a G sat alongside mine? I’d like to track it but as usual she didn’t have anymore information for me such as boat etc.
i am super excited however my other half is a bit worried. The business has dropped a quieter and he’s concerned for the future.
I understand his concerns and I’m trying to stay positive, and making a real effort to keep him positive and upbeat too. It’s hard at the moment for everybody.
Woohooo!!!!
This car had an original build date 13April. Is anybody else likely to have a G sat alongside mine? I’d like to track it but as usual she didn’t have anymore information for me such as boat etc.
i am super excited however my other half is a bit worried. The business has dropped a quieter and he’s concerned for the future.
I understand his concerns and I’m trying to stay positive, and making a real effort to keep him positive and upbeat too. It’s hard at the moment for everybody.
#59
I had my whole 19 G550 covered in Stealth PPF and sold the vehicle because of it. While it gave it an awesome look and was super easy to clean and felt protected...
there were many bubbles , exposed seams that would want to lift, stretch marks in obvious spots, and with sunglasses on it would look like the truck was torched by a flame gun. In addition, the trim and everything never felt the same or as solid as originally. I paid 8800.
on my new g63 I just picked up I have opted to do the hood , mirrors , and the front clip by a different installer, and have no parts removed & have ceramic coating going on whole vehicle. I’m convinced I’m going to be much happier this time around... Doing the sides of the G’s just seem too difficult for any installer since the pieces are too big and how Mercedes has the trim pieces put together.
there were many bubbles , exposed seams that would want to lift, stretch marks in obvious spots, and with sunglasses on it would look like the truck was torched by a flame gun. In addition, the trim and everything never felt the same or as solid as originally. I paid 8800.
on my new g63 I just picked up I have opted to do the hood , mirrors , and the front clip by a different installer, and have no parts removed & have ceramic coating going on whole vehicle. I’m convinced I’m going to be much happier this time around... Doing the sides of the G’s just seem too difficult for any installer since the pieces are too big and how Mercedes has the trim pieces put together.
The car was wrapped by Keyvon at ACAP Films Main Line outside of Philadelphia. They came highly recommended from the dealer and my detailer. In the past I used a closer installer but decided to use a "higher end" installer based on the fact that he's wrapped a few new FGT's and Chiron's. The complete wrap was 9k in xpel stealth. The wrap is AWFUL. The truck has been back for once repair and it is still not fixed. The doors are rattling because he didn't reassemble the door panels correctly. This work is absolute garbage. There are uneven edges, areas not pushed down, and areas that look like they ripped the film instead of cutting it. There are also wrinkles at the edges. I emailed Xpel and they basically responded with "Its an installer issue" and good luck to you. This is fifth and last car I will wrap with Xpel. I may switch back to 3m or Suntec. When I asked why it looks like ****, the answer was that "Xpel stealth is hard to work with and that the G63 is the hardest car to wrap in the industry". If this isn't fixed I'm going to be the squeaky wheel on their instagram, facebook, yelp and google pages warning others.
The following users liked this post:
Bexlee (06-02-2020)
#60
Bexlee,
This should give you a good idea of timing. My G is on this ship, had a build date of 3rd decade of April.
And you are not alone with those feelings, my wife has the same concerns.
This should give you a good idea of timing. My G is on this ship, had a build date of 3rd decade of April.
And you are not alone with those feelings, my wife has the same concerns.
The following users liked this post:
Bexlee (06-04-2020)
#61
Member
Join Date: Jan 2020
Location: West Yorkshire, UK.
Posts: 200
Received 57 Likes
on
30 Posts
G350d, Rover Mini , Abarth 500, G230, RS4
CClement-
Thank you very much for this information. Our G is coming to the U.K. so hopefully it won’t be long at all :-) Maybe even arrive at port this week :-D
My day to day car is a 1996 Rover Mini so this is a whole new ball game for me!! It’s going to be fun!
Thank you very much for this information. Our G is coming to the U.K. so hopefully it won’t be long at all :-) Maybe even arrive at port this week :-D
My day to day car is a 1996 Rover Mini so this is a whole new ball game for me!! It’s going to be fun!
#62
Senior Member
I have Suntek on my Porsche and plan to use the same on my G when it arrives. My installer is top notch and he uses the patterns, which wrapped edges on my car so don't be deterred from an installer that uses those as opposed to custom cut pieces. There are several excellent installers on Rennlist that also use the templates and they all say the same.
The car was wrapped by Keyvon at ACAP Films Main Line outside of Philadelphia. They came highly recommended from the dealer and my detailer. In the past I used a closer installer but decided to use a "higher end" installer based on the fact that he's wrapped a few new FGT's and Chiron's. The complete wrap was 9k in xpel stealth. The wrap is AWFUL. The truck has been back for once repair and it is still not fixed. The doors are rattling because he didn't reassemble the door panels correctly. This work is absolute garbage. There are uneven edges, areas not pushed down, and areas that look like they ripped the film instead of cutting it. There are also wrinkles at the edges. I emailed Xpel and they basically responded with "Its an installer issue" and good luck to you. This is fifth and last car I will wrap with Xpel. I may switch back to 3m or Suntec. When I asked why it looks like ****, the answer was that "Xpel stealth is hard to work with and that the G63 is the hardest car to wrap in the industry". If this isn't fixed I'm going to be the squeaky wheel on their instagram, facebook, yelp and google pages warning others.
I used Exclusive Vinyl in NY for a vinyl wrap (easier than XPEL tho) on my R8. Been watching their work for many years already, best edges I've seen. Full overlap, door card/door sill all done. Only thing is he's pretty backed up. He quoted me 2 weeks, but took 4. Also hated the drive then rental arrangement.
The following users liked this post:
Bexlee (06-18-2020)
#63
MBWorld Fanatic!
IN MY EXPERIENCE - I wrapped my 2018 GTR all over and frankly after spending the money don’t think it is worth the extra expense as opposed to a front end and windshield wrap.
I just had my 2020 G63 wrapped and the windshield done and am very pleased with the results;
XPEL PRO
Complete front end to the front door edges except the bull bar to include;
Complete Hood,
Front end around the grill and intake vents
Front Fenders
Front Fender Flairs - Complete from front end to the running board.
Headlight Lenses (a cracked/broken lense is very expensive)
Windshield Frame Complete
Running Boards outer edges
Sill Plates - All four and rear cargo sill trim plate
Mirror housings - flat wrap
EXOSHIELD - Complete Windshield Protectionhttps://www.getexoshield.com/
Complete Windshield
Somebody described the G Wagon perfectly when they said “It’s a beautiful brick” going down the road.
With that in mind, my project goal was to minimize/eliminate front end paint chips, dents and scratches and windshield chips/cracks.
Hopefully, I have accomplished my goal. We’ll see over time.
IN MY EXPERIENCE - For those who are considering these projects, please remember what has been said many, many times, the installer and using high quality products are the key to a good job. In other words you get what you are willing to pay for.
Regards
Jerry
I just had my 2020 G63 wrapped and the windshield done and am very pleased with the results;
XPEL PRO
Complete front end to the front door edges except the bull bar to include;
Complete Hood,
Front end around the grill and intake vents
Front Fenders
Front Fender Flairs - Complete from front end to the running board.
Headlight Lenses (a cracked/broken lense is very expensive)
Windshield Frame Complete
Running Boards outer edges
Sill Plates - All four and rear cargo sill trim plate
Mirror housings - flat wrap
EXOSHIELD - Complete Windshield Protectionhttps://www.getexoshield.com/
Complete Windshield
Somebody described the G Wagon perfectly when they said “It’s a beautiful brick” going down the road.
With that in mind, my project goal was to minimize/eliminate front end paint chips, dents and scratches and windshield chips/cracks.
Hopefully, I have accomplished my goal. We’ll see over time.
IN MY EXPERIENCE - For those who are considering these projects, please remember what has been said many, many times, the installer and using high quality products are the key to a good job. In other words you get what you are willing to pay for.
Regards
Jerry
Last edited by JSwan724; 06-20-2020 at 09:08 AM.
The following users liked this post:
Bexlee (06-04-2020)
#65
The following users liked this post:
Bexlee (06-18-2020)
The following users liked this post:
Bexlee (06-19-2020)
#71
MBWorld Fanatic!
Called around to various dealers yesterday and one an hour away received a spec brown G63 for $175k they are selling for $190k. They are the only dealer in NC that upcharges. They may sell out of market but the other dealers selling for sticker are pretty adamant about selling in market only.
Last edited by Hodog16; 06-19-2020 at 10:11 AM.
#72
MBWorld Fanatic!
iTrader: (1)
Join Date: Dec 2019
Location: Marineland FL
Posts: 2,167
Likes: 0
Received 462 Likes
on
377 Posts
'25 EQG deposit, '21 718 Spyder & '20 HD Fatboy
Called around to various dealers yesterday and one an hour away received a spec brown G63 for $175k they are selling for $190k. They are the only dealer in NC that upcharges. They may sell out of market but the other dealers selling for sticker are pretty adamant about selling in market only.
#73
Junior Member
#74
MBWorld Fanatic!
Yeah I wasn't sure about the allocations but I clarified it's for 2021. I just got the green light to get it, so I'm going back today to test drive with and without adaptive suspension and put a deposit down! Will post more details later!