Gear swap
#1
Super Member
Thread Starter
Gear swap
Hey goes does anyone know which ring and pinions work for an 06 S55? I want to go 3.07 or 3.27. Thanks!
#3
Super Member
Thread Starter
I didn’t think that would help seeing as these cars didn’t come with any other ratio but stock but here it is. Thanks!
WDBNG74J86A482876
WDBNG74J86A482876
#4
Out Of Control!!
You are correct there are no other gear sets offered by the factory,however you will also have to reprogram your TCU and other control modules to accept the ratio change----dream on!
#5
Super Member
Thread Starter
It’s not a dream, I own Star and have already talked with Jerry who has done a few hundred of these gear swaps, it’s just a matter of finding the right gears for me rear end as he is just the tuner... it’s not hard to set the TCU and ECU for the swap at all, they will take upto 3.27’s
#6
MBWorld Fanatic!
Join Date: Aug 2006
Location: A.D., U.A.E
Posts: 7,002
Likes: 0
Received 377 Likes
on
342 Posts
00 C200 & 00 C55 & 06 SLK55
Yeah, my friend done that 3 years ago,
he installed "3.27", but not sure from which M/Y diff. he went with, and adapt the TCU as well,
most tuners can do it,
soooo fun.., much wheel spin from dig, but really gain some ET's then..,,
i tried to contact him, but his Cell switched-off, seems his out of country..
-;ZAYED;-
he installed "3.27", but not sure from which M/Y diff. he went with, and adapt the TCU as well,
most tuners can do it,
soooo fun.., much wheel spin from dig, but really gain some ET's then..,,
i tried to contact him, but his Cell switched-off, seems his out of country..
-;ZAYED;-
Trending Topics
#9
Super Member
Thread Starter
Thanks,
Quaife didn’t seem to know or want to tell me which was a surprise, and Marc hasn’t written back yet, and that was about a week or two ago so I guess I’ll try to reach out to him again but didn’t figure he would be a big help on the differential end.
Thanks
Chris
Quaife didn’t seem to know or want to tell me which was a surprise, and Marc hasn’t written back yet, and that was about a week or two ago so I guess I’ll try to reach out to him again but didn’t figure he would be a big help on the differential end.
Thanks
Chris
#10
MBWorld Fanatic!
Join Date: Apr 2009
Posts: 1,041
Received 264 Likes
on
213 Posts
'06 MB S55 AMG; '04 Audi Allroad 4.2; '05 BMW M3 Conv.; '92 MB 500E
Interesting re: Quaife. I've found over the years that Marc works better by phone. I'd also try Wavetrac, again by phone. Finally, Jonothan Hodgman, down at Blue Ridge MB (outside Atlanta) might know. 404.805.1357; www.blueridgemb.com; @blueridgemb. Jono is the one who first told me about Wavetrac LSD for these cars. Depending upon where you are geographically, Hodgman might be a good one to know in person.
GL
maw
GL
maw
#11
MBWorld Fanatic!
Join Date: Aug 2006
Location: A.D., U.A.E
Posts: 7,002
Likes: 0
Received 377 Likes
on
342 Posts
00 C200 & 00 C55 & 06 SLK55
Chris,
My friend called me hour ago,
he said; he used diff. & axles from "2000 S280",
he also used propeller shaft rear one only (that attach to diff.),
cause S55 uses (4) fingers, while "S280" uses (3) fingers,
so many guys tell him to not use "S280" diff., cause i think it uses small carrier (210HAG), it will not handle the "S55K" tq/power,,
but he used the car around "3" years without any issues..
-;ZAYED;-
My friend called me hour ago,
he said; he used diff. & axles from "2000 S280",
he also used propeller shaft rear one only (that attach to diff.),
cause S55 uses (4) fingers, while "S280" uses (3) fingers,
so many guys tell him to not use "S280" diff., cause i think it uses small carrier (210HAG), it will not handle the "S55K" tq/power,,
but he used the car around "3" years without any issues..
-;ZAYED;-
#12
Super Member
Thread Starter
Thanks for the info! Unfortunately I have a Quaife installed in my rear diff so I want to keep my diff and find a ring and pinion to match.
Thanks again though!
Thanks again though!