When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Are you saying you have two of these light fixtures and that one of them is working?
If so, and if you are familiar with how to use a multimeter, you stand a good chance of finding the fault.
The fixture in this pic looks a little different than the one in your posts above... one of the LED mounting holes is broken.
If you look at the 8 orange pads in this pic, the top right one appears to be a “plated through hole” solder connection. However, the solder does not appear to be adhering to the sides of the hole and may be causing an open circuit.
If you take a closer look and are confident that’s the case, you could try reflowing that connection.
is same one, Jørgen just tryed get to whats under the black coat for measure , thats the damage you see.
While O.P's LED's may be functional. And LED's are typically pretty robust.
But for anyone who may need to undertake this repair in the future, even if on a different model MB.
There appears to be plenty of old stock of the OSRAM Dragon LED's in yellow and white available on eBay. (some in europe) Just have to determine the exact CRI/spec. you may need.
Jørge Østvik Trondheim Norway fixed the case with a ford starter for the led light , and soldering in wires direct on the LED lamp , bypassed all electronic on the light card , just amazing .
Somewhat unorthodox fix, but effective...
It will be interesting to see if moisture resistance and longevity are affected.
I would look for a cheap used headlight, even if broken, to salvage a functioning LED board if you come across one cheap.
Something like this below: (unfortunately this one probably has US yellow LED/lights)
Somewhat unorthodox fix, but effective...
It will be interesting to see if moisture resistance and longevity are affected.
I would look for a cheap used headlight, even if broken, to salvage a functioning LED board if you come across one cheap.
Something like this below: (unfortunately this one probably has US yellow LED/lights)
I’m a little concerned about the lack of voltage regulation, as well as no current limiting resister in series with the LED. As the LED warms up it will draw more current and may eventually go into thermal runaway, smoking the LED, and perhaps even blowing a fuse.
Last edited by hornethandler; Apr 24, 2023 at 07:10 PM.
Just curious... how did you drop (reduce) the voltage from the connector to the 3 volts necessary to operate the LED?
the reducer from the FORD ,that start the LED to light , the one you see on the left in picture.
Someone need take some action against mercedes ,one park lamp gone , and cant buy a 20 dollar part. is totaly wrong . Buy a hole lamp that nobody really need, guess is many others have same issue, or will have it sometime.
I’m a little concerned about the lack of voltage regulation, as well as no current limiting resister in series with the LED. As the LED warms up it will draw more current and may eventually go into thermal runaway, smoking the LED, and perhaps even blowing a fuse.
the ford starter is the regulator, how it will work long term ,we dont know, the warning light inside also go away. So its test and see . hope for the best.
yes, the grill really lifted the car alot , is also alot horsepower , is tuned ECU , and from dead stock , trotthle and turbo response is like another car, i have different AMG , but drive this one, i did not even bother push the trotthle was so slow on getting response . But after tuning, is like wow ,smoking rear tires in second gear at half trotthle. car is SL500, USA named 550 . Fuel use is also lowered around 0,9 liter per 10 km in speed 130 to 140 KMH
the reducer from the FORD ,that start the LED to light , the one you see on the left in picture.
Someone need take some action against mercedes ,one park lamp gone , and cant buy a 20 dollar part. is totaly wrong . Buy a hole lamp that nobody really need, guess is many others have same issue, or will have it sometime.
I'm glad you came up with a fix. It will be interesting to see how it works out, and I'm looking forward to hearing more once you've run it for awhile.
park light taken out , is led . but where to order this one. had to drill hole in assembly to get to skrew to take it out .
Hello Tommyboy928,
Greetings from germany, i have the same problem. I found the manufacturer of the led pcb. I will attach the links here.
Can you tell me what steps did you do to get to the screw to take the pcb out? Did you remove the glas or will it be self explanatory?
Thank you in advance for your answer.
Best regards,
Greetings from germany, i have the same problem. I found the manufacturer of the led pcb. I will attach the links here.
Can you tell me what steps did you do to get to the screw to take the pcb out? Did you remove the glas or will it be self explanatory?
Thank you in advance for your answer.
Best regards,
Mercedes SLR McLaren 722 S Is Extremely Rare Example Modified by McLaren
Slideshow: A one-of-one U.S.-spec Mercedes-Benz SLR McLaren Roadster became even rarer after a factory-backed transformation at McLaren's headquarters.
