water pump?
01-08-2007, 01:17 AM
#1
Super Member
Thread Starter
Join Date: Sep 2006
Location: New Jersey
Posts: 659
Likes: 0
Received 0 Likes
on
0 Posts
1989300CE(sold),1996Accord,02CBR954
water pump?
--------------------------------------------------------------------------------
I have a water pump that need changing on a 89 300ce.Whats involved ?I read somewhere that damn near everthing in the front of the car has to be taken out.I was hoping to just remove/loosen the belt and disconnect the hoses.Do i need a pulley remover?is there any special tools ?...
This car is worse the an gold digger.thing just stays in my pocket
I have a water pump that need changing on a 89 300ce.Whats involved ?I read somewhere that damn near everthing in the front of the car has to be taken out.I was hoping to just remove/loosen the belt and disconnect the hoses.Do i need a pulley remover?is there any special tools ?...
This car is worse the an gold digger.thing just stays in my pocket
01-08-2007, 02:12 AM
#2
MBWorld Fanatic!
Join Date: Jun 2005
Location: San Diego Californ-i-a
Posts: 1,467
Likes: 0
Received 0 Likes
on
0 Posts
89 300TE, and 68 280sel
aw, I have been there. You have to take the fan off, and the belt, loosen the belt tensioner etc, take the filter housing off,etc, it isn't hard, but it isn't a snap. def, an afternoon job, long afternoon if you have beers involved like I did, compliments of my friends
.
.
01-08-2007, 01:26 PM
#3
Super Member
Thread Starter
Join Date: Sep 2006
Location: New Jersey
Posts: 659
Likes: 0
Received 0 Likes
on
0 Posts
1989300CE(sold),1996Accord,02CBR954
aw, I have been there. You have to take the fan off, and the belt, loosen the belt tensioner etc, take the filter housing off,etc, it isn't hard, but it isn't a snap. def, an afternoon job, long afternoon if you have beers involved like I did, compliments of my friends .
.
01-08-2007, 01:54 PM
#4
MBWorld Fanatic!
Join Date: Jul 2005
Location: Boston
Posts: 3,094
Likes: 0
Received 0 Likes
on
0 Posts
is a German Tank
01-08-2007, 02:43 PM
#5
Super Member
Thread Starter
Join Date: Sep 2006
Location: New Jersey
Posts: 659
Likes: 0
Received 0 Likes
on
0 Posts
1989300CE(sold),1996Accord,02CBR954
I just took a good look at it..,I dont think I want to tackle this ****.the fan,tensioner housing,belt and the rest of my hair Has to come out.I really dont want to try this on my own without a manual.But,i dont really have 5/6 hundred laying around for a mechanic either.Seem like everytime I spend money on something that that car doesnt really need.Something happen soon after that needs attention right away.I have parts piling up. motor mounts,flex disc,fuel pump relay that I havent even addressed yet.not to mention the other little bull**** I want to do.
thanks
Trending Topics
01-09-2007, 08:55 AM
#9
Member
this might be a good time to look around the area and do everything else, AND a great time to de-scale the cooling system before you replace the pump. what I mean is - new hoses,clamps, maybe a belt, replace p.steer fluid/filter, is the tensioner good?, plug wires?, dist cap & rotor?, just all those things that you move/touch/loosen.....fan clutch.....ect....part $$ the same, but at least you only do the labor once
01-09-2007, 12:46 PM
#10
Super Member
Thread Starter
Join Date: Sep 2006
Location: New Jersey
Posts: 659
Likes: 0
Received 0 Likes
on
0 Posts
1989300CE(sold),1996Accord,02CBR954
this might be a good time to look around the area and do everything else, AND a great time to de-scale the cooling system before you replace the pump. what I mean is - new hoses,clamps, maybe a belt, replace p.steer fluid/filter, is the tensioner good?, plug wires?, dist cap & rotor?, just all those things that you move/touch/loosen.....fan clutch.....ect....part $$ the same, but at least you only do the labor once
Actually i took my car to my friends import shop(hondas)and he said the water pump is ok.Its the fan bearing thats making the noise.I really wish I had the change for everything
01-12-2007, 12:26 AM
#13
Super Member
Thread Starter
Join Date: Sep 2006
Location: New Jersey
Posts: 659
Likes: 0
Received 0 Likes
on
0 Posts
1989300CE(sold),1996Accord,02CBR954
01-13-2007, 02:06 PM
#15
MBWorld Fanatic!
Join Date: Dec 2003
Posts: 1,016
Likes: 0
Received 0 Likes
on
0 Posts
do some research before you start.
when i did it, i printed three separate write ups from mercedes shop dot com that detailed the procedure the writers had used. i taped them to the wall of the garage i was working in. and i referred to them constantly.
i DID NOT take off the fan.
you WILL need a long skinny extension bar (i used a 1/4' drive long extension, the requisite 1/4 and 3/s converters and wobble extensions.)
also its easy to take off the wrong bolts. after i took off wht i thought was the last bolt on the waterpup i struggled to remove it for quite a while before bending down to realise that the bolt i should have removed was above the one i did remove. i couldnt see it without bending over.
be prepared to replace your belt tensioner as well. apparently its not uncommon for them to be on thier last legs and then when you reinstall them, they dont work. i learned this one the hard way.
and if youre there, you may as well replace the belt and the belt tensioner strut. its all stuff that needs to come off anyway,its cheap insurance against having to do it again sometime soon.
when i did it, i printed three separate write ups from mercedes shop dot com that detailed the procedure the writers had used. i taped them to the wall of the garage i was working in. and i referred to them constantly.
i DID NOT take off the fan.
you WILL need a long skinny extension bar (i used a 1/4' drive long extension, the requisite 1/4 and 3/s converters and wobble extensions.)
also its easy to take off the wrong bolts. after i took off wht i thought was the last bolt on the waterpup i struggled to remove it for quite a while before bending down to realise that the bolt i should have removed was above the one i did remove. i couldnt see it without bending over.
be prepared to replace your belt tensioner as well. apparently its not uncommon for them to be on thier last legs and then when you reinstall them, they dont work. i learned this one the hard way.
and if youre there, you may as well replace the belt and the belt tensioner strut. its all stuff that needs to come off anyway,its cheap insurance against having to do it again sometime soon.
01-14-2007, 08:42 AM
#16
Super Member
Thread Starter
Join Date: Sep 2006
Location: New Jersey
Posts: 659
Likes: 0
Received 0 Likes
on
0 Posts
1989300CE(sold),1996Accord,02CBR954
do some research before you start.
when i did it, i printed three separate write ups from mercedes shop dot com that detailed the procedure the writers had used. i taped them to the wall of the garage i was working in. and i referred to them constantly.
i DID NOT take off the fan.
you WILL need a long skinny extension bar (i used a 1/4' drive long extension, the requisite 1/4 and 3/s converters and wobble extensions.)
also its easy to take off the wrong bolts. after i took off wht i thought was the last bolt on the waterpup i struggled to remove it for quite a while before bending down to realise that the bolt i should have removed was above the one i did remove. i couldnt see it without bending over.
be prepared to replace your belt tensioner as well. apparently its not uncommon for them to be on thier last legs and then when you reinstall them, they dont work. i learned this one the hard way.
and if youre there, you may as well replace the belt and the belt tensioner strut. its all stuff that needs to come off anyway,its cheap insurance against having to do it again sometime soon.
when i did it, i printed three separate write ups from mercedes shop dot com that detailed the procedure the writers had used. i taped them to the wall of the garage i was working in. and i referred to them constantly.
i DID NOT take off the fan.
you WILL need a long skinny extension bar (i used a 1/4' drive long extension, the requisite 1/4 and 3/s converters and wobble extensions.)
also its easy to take off the wrong bolts. after i took off wht i thought was the last bolt on the waterpup i struggled to remove it for quite a while before bending down to realise that the bolt i should have removed was above the one i did remove. i couldnt see it without bending over.
be prepared to replace your belt tensioner as well. apparently its not uncommon for them to be on thier last legs and then when you reinstall them, they dont work. i learned this one the hard way.
and if youre there, you may as well replace the belt and the belt tensioner strut. its all stuff that needs to come off anyway,its cheap insurance against having to do it again sometime soon.
Thanks for the tips I already replaced the tensioner, belts & shock.
This ***** just doesnt appreciate nothing.
