gzim335

Like title says I need to know what plugs you guys are running with stage 3 weistec blowers,I have 3k miles on my stage 3 n went thru 6 sets of plugs,just installed a fresh set 3 days ago as I had a racing event today and car ran smooth when I installed,started car this morning after cold start car started missing again fml
No check engine light or anything just a miss idling,car runs strong when wot.
Tried to reach weistec past 3 weeks to no success,I need to figure out which plug is suited for blown cars and which gap?
Thank you guys

m a x i m u s

Weistec sells plugs for SC applications.

gzim335

Lol I been trying to reach them I give up

Asher4799

Go to the Weistec site and in the w204 page under engine upgrades you can buy the plugs they are $119

mr747

Who are you emailing?? Couple of the boys have left

Call them gzim speak to Zach

63c

if you get misfire that mean 1or 2 broke bro happened to me even if new 😂

Southways

We (Magnuson) supply NGK ILZKR7B11 plugs with our Hammer kit and have not experienced any issues. The ILZKR7B11 have a 16mm hex (OEM is 14mm) so you need a 16mm socket that is 20.7mm or less outside diameter to fit down the cam-cover sleeve.
You should be able to get a set of ILZKR7B11 for under US$80 with a bit of hunting.

gzim335

Thank you so much,what should I gap them at?

Southways

Before gapping, check this out:
http://www.ngk.com/learning-center/a...g-instructions
and
http://www.ngk.com/learning-center/a...i-gap-my-plugs

I run mine at 0.80mm (0.031"), but some of our installers run a little less (0.70-0.75).

gzim335

Looked everywhere locally for a 16mm socket that's that thin to no success,does someone make it special or where do I get that socket

m a x i m u s

Did you check harbor freight.com?

gzim335

I did n they have thin wall but I don't think it will fit,less than 20.7mm diameter means paper thick wall lol I don't know where to buy it

cays

Ask and ye shall receive:

http://www.ebay.com/itm/Sealey-AK655...-/111930649605

gzim335

That won't work I bought every thin wall 16mm socket I found n they all too big,it needs to be less than 20.7mm in diameter

cays

Ah, I see. I'd live chat with Snap-on on Mon and see if they carry one or have a lead to source one. If they don't have it you may well be out of luck. They may be out there as an mfr dealer tool but you'll have to hunt one down.

gzim335

Found one on eBay but it's in China way too long to get here

dubzAMG

The customer service at weistec has taken a plunge. Supposedly they are under staffed and are having "problems" with there phone lines.

dubzAMG

I used a 3/8 drive thin wall snap on socket when I changed mine.

gzim335

Did u put 16mm plugs?oem is only 14

dubzAMG

I used brisk plugs, regardless a snap on thin wall socket should work for you.Doesn't have to be a "spark plug" specific socket, all that it does is holds the spark plug in the socket without falling out.

gzim335

If that was the case I'd drop the plug in with pliers bro haha how m I suppose to screw it in lol,which brisk u using and what's ur setup

dubzAMG

I just have header,exhaust,tune.Using one step colder plugs. Check with snap on, there sockets are thinner than other manufactures, so you can get it in the tube to torque down the plugs.

Southways

I originally had a Koken 5/8" deep 3/8" drive that fits ... as Dub says, it is not a spark plug specific version & I used a piece of rubber tube to grab the plug.
I have since found two other proper spark-plug sockets - one is from a local (Au) supplier & the other is a China supplier that we now buy in bulk and offer as part of a workshop installer kit.

I have been told that http://www.mactools.com/en-us/Specia...rk-Plug-Socket fits, but I suggest you call them and confirm.

However - most installing workshops simply buy a cheap (PepBoys, Napa, autozone or similar) 5/8" socket and turn it down.

Southways

An 8" long piece of 5/16" fuel hose pushed over the plug ceramic, screw the plug in until it seats, then torque with the socket.
NGK used to sell (gift) a moulded tube for it ... a long time ago.

gzim335

I don't have the socket can't get it anywhere