Lowering Springs for 4MATIC W211's GAUGING INTEREST
#51
MBWorld Fanatic!
Thread Starter
UPDATE!
Sorry for all the posts today but things have gotten a bit confusing. The tracking number I was given today for expected arrival next Thursday showed up at the door TODAY! However, it is only the front springs, the rears are still on the way. I took some quick pictures of the springs to show to you guys. They are definatly prototype as there are no serial numbers or markings anywhere on the spring. They don't even say vogtland! I love the exclusiveness! Anyhow, have a look at the fronts and check back in soon as I'm sure the rears will be here shortly! Thanks for looking stay tuned
#53
MBWorld Fanatic!
Thread Starter
They are IN!!!
I finally got the other half of the spring package!! I know have the 1st complete W211 4Matic spring package ever produced! Super excited as I'm sure you all can tell. I can't wait to see how handling improves and I know it will look better as it really needs that extra inch or so to look sporty.
Now, as far as the installation is concerned, I've decided to hold off until my carbon fiber interior package comes back so I can have the trim, door pins, shift knob and pedals installed at the same time as the springs. Down time is important so I like to do everything at once. I know you are all eager, but it won't be much longer now. If you have been following my carbon fiber thread, it is nearly finished. I should have it back late next week I imagine. So, figure two weeks from now, mid march, this should be getting underway. Stay tuned
Now, as far as the installation is concerned, I've decided to hold off until my carbon fiber interior package comes back so I can have the trim, door pins, shift knob and pedals installed at the same time as the springs. Down time is important so I like to do everything at once. I know you are all eager, but it won't be much longer now. If you have been following my carbon fiber thread, it is nearly finished. I should have it back late next week I imagine. So, figure two weeks from now, mid march, this should be getting underway. Stay tuned
#55
MBWorld Fanatic!
Thread Starter
Within a week they should be able to produce a few more sets.
#57
MBWorld Fanatic!
Thread Starter
Hey there welcome. I'll be putting them on pretty soon I have to wait until I get my carbon fiber interior back so I can install everything all at once. Do stay posted thanks for ur interest. You wouldn't happen to live around Costa Mesa would ya? I'm trying to have brakes made as well and could use some help.
#63
Super Member
yes please update, especially if you can get them installed it would probably get more interest from other members.
I have H&R on my 4matic now but the front sit slightly higher than the rear (same for the 2wd guys) so if the ride quality and the front and rear actually even out this would be great.
Also, I've been searching for quite some time but haven't found shocks for our car. The rears are the same as the 2wd but the fronts are actually short shocks so no luck there. Has anyone found aftermarket shocks?
I have H&R on my 4matic now but the front sit slightly higher than the rear (same for the 2wd guys) so if the ride quality and the front and rear actually even out this would be great.
Also, I've been searching for quite some time but haven't found shocks for our car. The rears are the same as the 2wd but the fronts are actually short shocks so no luck there. Has anyone found aftermarket shocks?
#65
Super Member
Which inserts are you talking about? I read a lot about these shims that people talk about on here but I think that's only for the sports package with airmatic.
If you're talking about the router inserts on the uppoer part of the springs. those will not get any thinner. I replaced installed the springs myself and those rubbers are quite thin and it's meant there so it can not squeak.
#66
I believe that it is the shims, but they are not for the airmatic. With the airmatic, you can use the module to lower it. The shims are for the different E models. How much did the H&R setup lower the car?
#67
Super Member
some where close to 300 from what I remember.. The ride is decent but I have 19's so it doesn't help.
#69
Super Member
I don't know how much it actually dropped the car, but it says 1.5 to 2"
To give you an idea, the rear is flushed but the front have 1.5 finger gap.
To give you an idea, the rear is flushed but the front have 1.5 finger gap.
#70
Newbie
Join Date: Apr 2007
Location: Near Toronto
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
09 E350 4Matic Avant Garde, 07 BMW 335i Cabriolet M-Tech
Any update? I took delivery of my new 09 E350 4Matic Avant Garde on Mar 31 and I am definitely interested in lowering the car using your springs.
My car came with AMG styling package, 18" AMG wheels, and sport suspension which includes drilled front brake rotors.
My car came with AMG styling package, 18" AMG wheels, and sport suspension which includes drilled front brake rotors.
#71
MBWorld Fanatic!
Thread Starter
just got my interior appointments installed new wheels are paid for and I'll be installing the springs very very sooN! Its been a long time coming but surely will be worth it. Sorry for the wait.
#74
MBWorld Fanatic!
Thread Starter
Of course updates!
Yes, the time has come. I went down to the spring shop today Hackensack Spring in Hackensack NJ. They took a look at the suspension and determined that they were willing to do the install. Time is tomorrow @ 8 am! These are being installed on OEM wheels 245/40/18 Contis. I've got 19"s on the way I just have to decide what color they will be. For right now, knowing how they sit and perform on OEM should be a good start. I'll keep you posted wish me luck. BTW estimate was 98 bucks a wheel, 100 bucks alignment was about $500. Thnx for checkin in!