For the first time I was left stranded roadside...
#26
Thread Starter
Senior Member
Joined: Oct 2017
Posts: 302
Likes: 42
From: Saint Louis
2010 GL550 | 2020 S560
Another update... I believe I was able to pinpoint my leak. I've attached better photos. My question is, since this appears to be a hose that comes off the power steering reservoir and connects into the radiator cause over heating?? I'm a DIYer and have been working on cars all my life. I'm somewhat stumped here.
#27
There are four penetrations into the side tanks, two for the transmission fluid cooling and two for the power steering fluid cooling. Each of these is sealed with an o-ring, which does not last forever. It is a real shame to discard a whole radiator because of these o-rings, but such is life. Fortunately the radiator is not all that expensive. Sooner or later the giant o-rings that seal the side tanks onto the aluminum fins will fail also.
The following users liked this post:
BlackML550 (01-09-2023)
#28
Thread Starter
Senior Member
Joined: Oct 2017
Posts: 302
Likes: 42
From: Saint Louis
2010 GL550 | 2020 S560
There are four penetrations into the side tanks, two for the transmission fluid cooling and two for the power steering fluid cooling. Each of these is sealed with an o-ring, which does not last forever. It is a real shame to discard a whole radiator because of these o-rings, but such is life. Fortunately the radiator is not all that expensive. Sooner or later the giant o-rings that seal the side tanks onto the aluminum fins will fail also.
to the radiator
#29
I don't think you can replace the o-rings. I think they are inside the tank. Tightening the external nut pulls the heat exchanger outward, compressing each o-ring against the inside of the tank wall.
My power steering fluid hoses began leaking where they attach to the heat exchanger fitting. I don't know what happens to the hoses, as they looked okay to me. But they did. That fluid rots rubber that is not prepared for it, such as the heater hose line that runs underneath the radiator.
It is your choice, but if I were you I would just go through and replace most everything there.
My power steering fluid hoses began leaking where they attach to the heat exchanger fitting. I don't know what happens to the hoses, as they looked okay to me. But they did. That fluid rots rubber that is not prepared for it, such as the heater hose line that runs underneath the radiator.
It is your choice, but if I were you I would just go through and replace most everything there.
#30
Thread Starter
Senior Member
Joined: Oct 2017
Posts: 302
Likes: 42
From: Saint Louis
2010 GL550 | 2020 S560
Appreciate the feedback Eric. I don't mind replacing the radiator but last time I took off the front bumper, I couldn't get it to fit back on properly.
Anyone able to remove the radiator without removing the bumper please advise.
Anyone able to remove the radiator without removing the bumper please advise.
#31
Take a look at YouTube channel Legitstreetcars - he takes radiator out of an 2006 ML 500 (I know, different because M113 motor) and does not remove bumper - and then proceeds to recommend against that method in hindsight.
#32
I ended up omitting about a third of the fasteners for the radiator etc. Also cut off the bottom of the shroud or cowling. I didn't have any trouble reattaching the bumper cover, though.
I have learned also to always remove the front fender liners when working in that general area. There's all this stuff that you assume is solid but it's actually just a removable plastic shell.
On those fender liners, replace the clip nuts and bolts with stainless steel. You still have to lube the threads - stainless likes to gall against stainless - but at least they won't corrode.
Last edited by eric_in_sd; 01-12-2023 at 07:24 AM.
#34
MBWorld Fanatic!
Joined: Aug 2003
Posts: 8,690
Likes: 1,098
From: In my garage
E55, GLS450, GL63, GLE350
It's super easy to remove. Remove the fender liner, unscrew the bolt holding the bumper to the body and pull out the metal sandwich plate holding the bumper to the body(swings out and back) - it's right there were the bumper cover meets the fender, loosen the bolts holding the bumper to the front of the car, then remove the under-panel screws holding it from below. Takes around 5 minutes after you've done it a few times. Getting the sandwich metal piece back on and that bolt to align can take some time though.
#35
Thread Starter
Senior Member
Joined: Oct 2017
Posts: 302
Likes: 42
From: Saint Louis
2010 GL550 | 2020 S560
I've removed it before when I retrofitted my headlights. I could not for the life of me get that curved bracket back on and in place. I suppose if I do remove the bumper this time I'll fully remove the wheel liners. I can't find anywhere online or on here a detailed description/instruction sheet on how to correctly remove and reassemble