Chinese Longtubes vs Reputable Mid’s
#53
Super Member
![](https://mbworld.org/forums/images/ranks/veteran_army.png)
#54
MBWorld Fanatic!
The following users liked this post:
Fountain35 (12-11-2018)
#56
Although maximizers are solid headers the XSP are a better option based on price alone, they are virtually the same.
https://www.youtube.com/watch?v=7rTqPm0HyOc&t=3s
https://www.youtube.com/watch?v=7rTqPm0HyOc&t=3s
#57
Former Vendor of MBWorld
from what i can tell in the video the install looked to be a pain and for someone who is not going to be installing the headers himself looks like it will cost an arm and a leg with all the small problems he ran into with the leak/fitment issues etc, but i guess the labour costs are offset with the already low price
#58
#59
Super Member
#60
ARH doesn't make equal length primaries because they've already discovered negligible to zero gains on supercharged applications. They've been in the game for a while.
Plus, most on this platform are too cheap to buy their existing product.
Plus, most on this platform are too cheap to buy their existing product.
#61
Super Member
![](https://mbworld.org/forums/images/ranks/veteran_army.png)
The following users liked this post:
AMG-SVT-FTW (12-06-2018)
#63
Super Member
![](https://mbworld.org/forums/images/ranks/veteran_army.png)
#64
cheap chinese, my shop told me they had terrible time fitting ARH headers on some other cars and the kleemanns were also a pain to install...they mentioned that they did install a set of maximizers and the fitment was pretty good so i went with those
#65
Super Member
#66
Super Member
![](https://mbworld.org/forums/images/ranks/veteran_army.png)
just got my upgraded cheap Chinese pipes last week. Planning on installing myself in my garage on my back. Is it very difficult
#67
#68
The issue is more than just than "quality" differences. It's the thickness of the piping used, which is crucial to retaining heat, and energy of exhaust gasses. The merge collectors on these Chinese systems are down right awful. They come together and neck down into a small exit in what looks like 3" of length. The merge collector, pipe routing, flange transition to piping, etc. has way more value than whether the system is "equal length". These motors aren't moving enough air, or turning enough RPM to get to the point where a properly designed un-equal length long tube header leaves power on the table. We have cars doing 8 seconds in the quarter with 4 digit power on 1-5/8" "unequal length" systems.
There's nothing like taking the entire car apart to put Chinese headers in there that you have to drill and slot mounting holes for, that have ports that are half blocked by the gasket due to zero quality control. Fighting past those things, let's say you get them on the car and 11 months down the road one of the primaries cracks off the flange and you now have to remove the entire system to get it "fixed" or re-install your factory system so you can drive to work.
If it's shiny, it's usually as thin as a piece of paper, and robotically welded with the cheapest production cost in mind.
There's nothing like taking the entire car apart to put Chinese headers in there that you have to drill and slot mounting holes for, that have ports that are half blocked by the gasket due to zero quality control. Fighting past those things, let's say you get them on the car and 11 months down the road one of the primaries cracks off the flange and you now have to remove the entire system to get it "fixed" or re-install your factory system so you can drive to work.
If it's shiny, it's usually as thin as a piece of paper, and robotically welded with the cheapest production cost in mind.
The following 2 users liked this post by ar headers:
Crissus (12-17-2018),
Fountain35 (12-10-2018)
#69
Super Member
![](https://mbworld.org/forums/images/ranks/veteran_army.png)
XSP, off Amazon. Think it’s different from VRP, below is the description: $800 free shipping... I said WTH! Alex trying it out. 😄
The ultimate bolt-on exhaust upgrade for your supercharged V8 AMG car FITS: 2003-2006 E55 AMG 2004-2006 CLS55 AMG -321 stainless steel, tig welded construction -Individual 1.95" Runners that form a uniform 4>1 3" tube merge collector thats been hand ported
The ultimate bolt-on exhaust upgrade for your supercharged V8 AMG car FITS: 2003-2006 E55 AMG 2004-2006 CLS55 AMG -321 stainless steel, tig welded construction -Individual 1.95" Runners that form a uniform 4>1 3" tube merge collector thats been hand ported
#70
MBWorld Fanatic!
The issue is more than just than "quality" differences. It's the thickness of the piping used, which is crucial to retaining heat, and energy of exhaust gasses. The merge collectors on these Chinese systems are down right awful. They come together and neck down into a small exit in what looks like 3" of length. The merge collector, pipe routing, flange transition to piping, etc. has way more value than whether the system is "equal length". These motors aren't moving enough air, or turning enough RPM to get to the point where a properly designed un-equal length long tube header leaves power on the table. We have cars doing 8 seconds in the quarter with 4 digit power on 1-5/8" "unequal length" systems.
There's nothing like taking the entire car apart to put Chinese headers in there that you have to drill and slot mounting holes for, that have ports that are half blocked by the gasket due to zero quality control. Fighting past those things, let's say you get them on the car and 11 months down the road one of the primaries cracks off the flange and you now have to remove the entire system to get it "fixed" or re-install your factory system so you can drive to work.
If it's shiny, it's usually as thin as a piece of paper, and robotically welded with the cheapest production cost in mind.
There's nothing like taking the entire car apart to put Chinese headers in there that you have to drill and slot mounting holes for, that have ports that are half blocked by the gasket due to zero quality control. Fighting past those things, let's say you get them on the car and 11 months down the road one of the primaries cracks off the flange and you now have to remove the entire system to get it "fixed" or re-install your factory system so you can drive to work.
If it's shiny, it's usually as thin as a piece of paper, and robotically welded with the cheapest production cost in mind.
The following users liked this post:
MSG 55G (12-06-2018)
#71
Super Member
![](https://mbworld.org/forums/images/ranks/veteran_army.png)
The issue is more than just than "quality" differences. It's the thickness of the piping used, which is crucial to retaining heat, and energy of exhaust gasses. The merge collectors on these Chinese systems are down right awful. They come together and neck down into a small exit in what looks like 3" of length. The merge collector, pipe routing, flange transition to piping, etc. has way more value than whether the system is "equal length". These motors aren't moving enough air, or turning enough RPM to get to the point where a properly designed un-equal length long tube header leaves power on the table. We have cars doing 8 seconds in the quarter with 4 digit power on 1-5/8" "unequal length" systems.
There's nothing like taking the entire car apart to put Chinese headers in there that you have to drill and slot mounting holes for, that have ports that are half blocked by the gasket due to zero quality control. Fighting past those things, let's say you get them on the car and 11 months down the road one of the primaries cracks off the flange and you now have to remove the entire system to get it "fixed" or re-install your factory system so you can drive to work.
If it's shiny, it's usually as thin as a piece of paper, and robotically welded with the cheapest production cost in mind.
There's nothing like taking the entire car apart to put Chinese headers in there that you have to drill and slot mounting holes for, that have ports that are half blocked by the gasket due to zero quality control. Fighting past those things, let's say you get them on the car and 11 months down the road one of the primaries cracks off the flange and you now have to remove the entire system to get it "fixed" or re-install your factory system so you can drive to work.
If it's shiny, it's usually as thin as a piece of paper, and robotically welded with the cheapest production cost in mind.
#72
Super Member
The issue is more than just than "quality" differences. It's the thickness of the piping used, which is crucial to retaining heat, and energy of exhaust gasses. The merge collectors on these Chinese systems are down right awful. They come together and neck down into a small exit in what looks like 3" of length. The merge collector, pipe routing, flange transition to piping, etc. has way more value than whether the system is "equal length". These motors aren't moving enough air, or turning enough RPM to get to the point where a properly designed un-equal length long tube header leaves power on the table. We have cars doing 8 seconds in the quarter with 4 digit power on 1-5/8" "unequal length" systems.
There's nothing like taking the entire car apart to put Chinese headers in there that you have to drill and slot mounting holes for, that have ports that are half blocked by the gasket due to zero quality control. Fighting past those things, let's say you get them on the car and 11 months down the road one of the primaries cracks off the flange and you now have to remove the entire system to get it "fixed" or re-install your factory system so you can drive to work.
If it's shiny, it's usually as thin as a piece of paper, and robotically welded with the cheapest production cost in mind.
There's nothing like taking the entire car apart to put Chinese headers in there that you have to drill and slot mounting holes for, that have ports that are half blocked by the gasket due to zero quality control. Fighting past those things, let's say you get them on the car and 11 months down the road one of the primaries cracks off the flange and you now have to remove the entire system to get it "fixed" or re-install your factory system so you can drive to work.
If it's shiny, it's usually as thin as a piece of paper, and robotically welded with the cheapest production cost in mind.
#75
Super Member
![](https://mbworld.org/forums/images/ranks/veteran_army.png)
SUPER CHEAP CHINESE HEADERS INSTALLED
XSP, off Amazon. Think it’s different from VRP, below is the description: $800 free shipping... I said WTH! Alex trying it out. 😄
The ultimate bolt-on exhaust upgrade for your supercharged V8 AMG car FITS: 2003-2006 E55 AMG 2004-2006 CLS55 AMG -321 stainless steel, tig welded construction -Individual 1.95" Runners that form a uniform 4>1 3" tube merge collector thats been hand ported
Did the install on my back, not too bad. Took some time to figure how to jam the driver side header in but eventually satisfied when it locked on and bolted down. Didn't have to push engine aside like "legitstreetcar", the rest of the pipes were not too bad neither. I worked from back to front, used a rubber hammer for alignment and adjustment, clamped, extended rear O2 sensors and popped them on spacers. No CEL!!! Didn't have to turn off O2.