MBWorld.org Forums
Share Your Pictures with Our Community. Upload Now
Next step is to jack up the engine by placing a 1 foot long 2 by 4 sideways ontop of the jack and jacking up infront of the sway bar about 1 to 2 inches. The further up the more room you have to push the sway bar out of the way.
Next step is to jack up the engine by placing a 1 foot long 2 by 4 sideways ontop of the jack and jacking up infront of the sway bar about 1 to 2 inches. The further up the more room you have to push the sway bar out of the way.
0 2015/08/09 21:25:40
next step is to loosen the upper motor mount bolts. You can see the top of the motor mounts underneath the exhaust.
next step is to loosen the upper motor mount bolts. You can see the top of the motor mounts underneath the exhaust.
0 2015/08/09 21:22:43
Next step is to remove the lower motor mount bolts
Next step is to remove the lower motor mount bolts
0 2015/08/09 21:21:26
Here is what the steering linkage looks like without the cover. It is loose and you can pull it down. Be advised that it is a pita to align the bolt holes back in place To resecure the linkage.
Here is what the steering linkage looks like without the cover. It is loose and you can pull it down. Be advised that it is a pita to align the bolt holes back in place To resecure the linkage.
0 2015/08/09 21:19:10
Another angle showing which nut needs to be removed.
Another angle showing which nut needs to be removed.
0 2015/08/09 21:17:37
Next undo the sway bar left and right side and hammer it off of the screw holding it in place to allow for some movement of the bar.
Next undo the sway bar left and right side and hammer it off of the screw holding it in place to allow for some movement of the bar.
0 2015/08/09 21:15:47
Another angle of the steering linkage with bracket on top.
Another angle of the steering linkage with bracket on top.
0 2015/08/09 21:14:19
Next step is to remove all three plastic covers from under the vehicle (not shown). Once the covers are off 8mm socket remove the metal cover and steering linkage.
Next step is to remove all three plastic covers from under the vehicle (not shown). Once the covers are off 8mm socket remove the metal cover and steering linkage.
0 2015/08/09 21:11:50
First step is to place the emergency brake on! Next jack up the car onto two jack stands facing opposite directions.
First step is to place the emergency brake on! Next jack up the car onto two jack stands facing opposite directions.
0 2015/08/09 21:09:42
Start by jaxking up each side of the car and placing the vehicle on jack stands one facing back and one facing forward. Don't forget to set the emergency brake!
Start by jaxking up each side of the car and placing the vehicle on jack stands one facing back and one facing forward. Don't forget to set the emergency brake!
0 2015/08/09 21:01:59
0 2015/08/09 20:12:06
0 2015/08/09 20:12:02
Advertisement
0 2015/08/09 20:11:21
0 2015/08/09 19:36:38
0 2015/08/09 19:36:17
0 2015/08/09 19:35:49
0 2015/08/09 19:35:28
CLK convertible hydraulic component locations
CLK convertible hydraulic component locations
0 2015/08/09 18:39:41
0 2015/08/09 18:39:23
Pic on my car from a while back
Pic on my car from a while back
0 2015/08/09 18:17:30
0 2015/08/09 18:16:26
0 2015/08/09 18:09:23
0 2015/08/09 18:09:03
0 2015/08/09 18:08:44
0 2015/08/09 18:08:10
The set
The set
0 2015/08/09 18:07:26
Rear wheel stamp
Rear wheel stamp
0 2015/08/09 18:06:43
Front wheel stamp
Front wheel stamp
0 2015/08/09 18:06:15
Worst bit of rash on one of the front wheels.
Worst bit of rash on one of the front wheels.
0 2015/08/09 18:05:38
Minor rash on one of the front wheels.
Minor rash on one of the front wheels.
0 2015/08/09 18:05:18
0 2015/08/09 17:58:42
0 2015/08/09 17:53:43
Advertisement