MBWorld.org Forums
0 2020/04/20 22:03:30
0 2020/07/21 13:09:08
0 2020/07/21 13:34:33
0 2020/07/21 13:35:17
new plugs. And 14mm socket
new plugs. And 14mm socket
0 2020/08/13 21:35:16
0 2020/08/13 21:36:21
Pulled plugs
Pulled plugs
0 2020/08/13 21:37:17
0 2020/08/31 20:13:56
Thread start point
Thread start point
0 2020/08/31 20:14:15
0 2020/09/07 09:56:47
0 2020/09/07 09:58:09
0 2021/05/27 14:55:16
0 2021/05/27 16:28:45
0 2021/05/27 16:28:53
0 2021/05/27 16:28:59
0 2021/06/01 09:33:12
0 2021/06/29 10:40:43
0 2021/06/29 12:04:42
Boot part number
Boot part number
0 2021/07/26 15:16:05
Pin hole leaking grease
Pin hole leaking grease
0 2021/07/26 15:16:11
Cv axle part number
Cv axle part number
0 2021/07/26 15:16:17
0 2021/08/09 10:29:56
0 2021/08/09 14:50:13
0 2021/08/09 14:50:16
Cam adjuster replacing. M274 engine
Cam adjuster replacing. M274 engine
0 2021/08/14 03:07:52
Intake cam adjuster inside. Work out pin hole side
Intake cam adjuster inside. Work out pin hole side
0 2021/08/14 03:07:57
Exhaust cam adjuster inside
Exhaust cam adjuster inside
0 2021/08/14 03:08:03
0 2021/08/14 03:29:29
To remove the engine mount braket, I needed to support the oil pan, then lift 1 cm after remove bolts.
To remove the engine mount braket, I needed to support the oil pan, then lift 1 cm after remove bolts.
0 2021/08/14 03:29:36
braket 4 bolts removed. Remove lower 2 bolts and 1 a/c bolt from under
braket 4 bolts removed. Remove lower 2 bolts and 1 a/c bolt from under
0 2021/08/14 03:29:44
Oil seperator is removed
Oil seperator is removed
0 2021/08/14 03:29:51
Old & new part
Old & new part
0 2021/08/14 03:30:00
0 2021/08/14 03:49:13
0 2021/08/14 03:49:19
0 2021/08/15 12:06:04
Tensioner cap
Tensioner cap
0 2021/08/15 12:19:38
Tensioner cap removed
Tensioner cap removed
0 2021/08/15 12:19:45
Tensioner and cap
Tensioner and cap
0 2021/08/15 12:19:51
Green gasket was so flat. I with i added some silicon under the gasket to raise the gasket height but i forgot to do. Or prepare new gasket.
Green gasket was so flat. I with i added some silicon under the gasket to raise the gasket height but i forgot to do. Or prepare new gasket.
0 2021/08/15 12:19:58
Cap center hole was covered with tape and silicon. Then installed back. And added some more silicone around.
Cap center hole was covered with tape and silicon. Then installed back. And added some more silicone around.
0 2021/08/15 12:28:15