MBWorld.org Forums
0 2021/08/10 19:41:19
0 2021/08/15 20:10:15
0 2021/08/15 20:25:04
0 2021/09/04 16:46:58
0 2021/09/04 16:47:03
After oem airboxes are removed you will have this
After oem airboxes are removed you will have this
0 2021/09/12 10:02:10
Grap a 13mm open end and loosen the 2 front ecu plastic screws
Grap a 13mm open end and loosen the 2 front ecu plastic screws
0 2021/09/12 10:02:15
Next remove the drivers side oem coupler. 2 flat head clamps and twist/pull the oem vent hose
Next remove the drivers side oem coupler. 2 flat head clamps and twist/pull the oem vent hose
0 2021/09/12 10:02:20
Apply some oil on the blackboost pipe so it slides in easier into the oem rubber coupler. Don't tighten it yet as u might need to make small adjustments when filters go on Be careful of the passanger side, I did not remove the oem coupler as I couldn't figure out how to remove the oem plastic vent hose, so I did it while it was on the car. Again with some oil on the coupler it slides in over the blackboost pipe without issue.
Apply some oil on the blackboost pipe so it slides in easier into the oem rubber coupler. Don't tighten it yet as u might need to make small adjustments when filters go on Be careful of the passanger side, I did not remove the oem coupler as I couldn't figure out how to remove the oem plastic vent hose, so I did it while it was on the car. Again with some oil on the coupler it slides in over the blackboost pipe without issue.
0 2021/09/12 10:02:24
Once the 2 front nuts are loose, Pull up on ecu to disconnect from the rubber grommets
Once the 2 front nuts are loose, Pull up on ecu to disconnect from the rubber grommets
0 2021/09/12 10:02:30
Next install drivers side intake box and install intake pipe to turbo inlet pipe, a dab of oil will help slide it in easier
Next install drivers side intake box and install intake pipe to turbo inlet pipe, a dab of oil will help slide it in easier
0 2021/09/12 10:02:38
Next put the oem air duct onto the blackboost box, again some oil will help slide it on easier. Same procedure on both sides.
Next put the oem air duct onto the blackboost box, again some oil will help slide it on easier. Same procedure on both sides.
0 2021/09/12 10:02:43
When installing the filter, u might have to wiggle it in slightly hence why leaving the hose clamps loose will help. The intake fits light this over the pipe and clamps on. After you get this installed you can tighten everything up.
When installing the filter, u might have to wiggle it in slightly hence why leaving the hose clamps loose will help. The intake fits light this over the pipe and clamps on. After you get this installed you can tighten everything up.
0 2021/09/12 10:02:47
Remove the air box air sensor by unplugging the clip, rotate counter clockwise and pull out, same procedure on either side of the intake box. You will use the oem harness on the passanger side to connect to the blackboost system
Remove the air box air sensor by unplugging the clip, rotate counter clockwise and pull out, same procedure on either side of the intake box. You will use the oem harness on the passanger side to connect to the blackboost system
0 2021/09/12 10:02:52
Lubricant the o ring on the sensor so it doesn't rip when pushing in, as pushing any rubber into a hole without lube will tear(giggity😏)
Lubricant the o ring on the sensor so it doesn't rip when pushing in, as pushing any rubber into a hole without lube will tear(giggity😏)
0 2021/09/12 10:02:57
Sensor installed, with the oem intake harness installed(passanger side) . Same procedure on drivers side (use supplied blackboost harness extension)
Sensor installed, with the oem intake harness installed(passanger side) . Same procedure on drivers side (use supplied blackboost harness extension)
0 2021/09/12 10:03:02
Now in drivers side, use the supplied blackboost intake harness extension, connect it to the oem connection on the back and route it to the front, same procedure as before, lube the intake air sensor, stick it in the blackboost intake pipe , and connect everything
Now in drivers side, use the supplied blackboost intake harness extension, connect it to the oem connection on the back and route it to the front, same procedure as before, lube the intake air sensor, stick it in the blackboost intake pipe , and connect everything
0 2021/09/12 10:03:06
Reinstall your ecu by clipping the back groumets first, then screwing in the 2 front 13mm plastic screws Finished product and ready for tuning!
Reinstall your ecu by clipping the back groumets first, then screwing in the 2 front 13mm plastic screws Finished product and ready for tuning!
0 2021/09/12 10:03:12
0 2021/09/21 16:16:13
0 2021/09/21 16:17:13
0 2021/09/21 16:17:38
0 2021/09/21 16:18:20
0 2021/09/22 07:52:36
0 2021/10/15 21:41:09
0 2021/10/16 05:59:45
0 2021/12/26 21:32:06
0 2021/12/26 21:32:19
0 2022/01/23 12:12:08
0 2022/02/18 06:37:22
0 2022/02/23 19:42:59
0 2022/02/25 06:17:49
0 2022/02/26 14:44:05
0 2022/05/25 11:07:29
0 2022/09/07 02:59:40
0 2022/10/30 12:32:30
0 2022/10/30 12:32:37
0 2022/10/30 12:32:43
0 2022/11/03 08:10:36
0 2023/02/02 11:19:53
0 2023/05/03 05:42:45