MBWorld.org Forums
0 2015/04/13 01:18:43
0 2015/04/13 01:19:16
0 2015/04/13 01:20:05
0 2015/04/13 01:20:53
0 2015/04/13 01:21:42
0 2015/04/13 01:23:00
0 2015/04/13 01:24:38
0 2015/04/13 01:25:13
late evening swedish summer.
late evening swedish summer.
0 2015/04/15 03:04:59
Yesterday 2014-04-18 Just finished paintprotection(Glare,Microfinish)
Yesterday 2014-04-18 Just finished paintprotection(Glare,Microfinish)
0 2015/04/19 02:33:53
Hope this clears up my issue.
Hope this clears up my issue.
0 2015/05/05 23:05:45
0 2015/05/22 00:11:17
0 2015/06/15 02:07:24
Porting being done
Porting being done
0 2015/06/24 06:40:05
Primer
Primer
0 2015/06/24 06:40:47
yes.. the discs at front are coroded, just a quick brake and they´re clean again.
yes.. the discs at front are coroded, just a quick brake and they´re clean again.
0 2015/06/28 20:31:49
0 2015/06/30 11:18:00
0 2015/07/08 10:43:05
0 2015/07/09 11:44:32
view from throttbody.
view from throttbody.
0 2015/08/05 12:22:46
just a teaser, need to grind a lot and seal it all up. But i´m getting there ;)
just a teaser, need to grind a lot and seal it all up. But i´m getting there ;)
0 2015/08/13 01:14:49
0 2015/08/18 07:21:41
0 2015/08/31 08:37:49
0 2015/09/02 05:49:07
0 2015/09/03 05:19:34
0 2015/09/04 01:15:08
Another angle, late night after work.
Another angle, late night after work.
0 2015/09/04 01:15:57
first test.. almost happy. Will make new ones almost alike theese.
first test.. almost happy. Will make new ones almost alike theese.
0 2015/09/05 12:16:41
This is just a test. but it´s an really simple mod. I´ll make new ones thou. Will move them about 10mm more into centrom of wheel.
This is just a test. but it´s an really simple mod. I´ll make new ones thou. Will move them about 10mm more into centrom of wheel.
0 2015/09/05 12:17:36
0 2015/09/06 22:33:14
Slowly getting there. A lot of cleanig up to do. Then i´m waiting for my flange to arrive. A friend of mine is getting it watercut for me. In picture, almost done with boxing it in completely.
Slowly getting there. A lot of cleanig up to do. Then i´m waiting for my flange to arrive. A friend of mine is getting it watercut for me. In picture, almost done with boxing it in completely.
0 2015/09/12 09:06:33
slowly getting there. grinding the flange by 'hand'. Only airtool for headporting as aid. takes time, and doesnt become eyecandy. But! i don´t care. this is an experiment, if it becomes an success i will go on developing an 3d model and then decide if print it out or cast it in alumium.
slowly getting there. grinding the flange by 'hand'. Only airtool for headporting as aid. takes time, and doesnt become eyecandy. But! i don´t care. this is an experiment, if it becomes an success i will go on developing an 3d model and then decide if print it out or cast it in alumium.
0 2015/09/14 05:45:18
looking awful. almost ashamed. But,, when developing a prototype i finf it useless to put effort in finish if the result was bad. In this case, result is really really good. but remember, i got longtube headers,ported heads,100cell cats, underdrive pulleys, 'needswings' bigger throttlebody(78mm) Now i feel the restrictions is in airmeter, and the 'knee', still oem, only mod here is no 'mesh' in airmeter and a small velocitystack inside the Y-pipe do guide air into airmeter.
looking awful. almost ashamed. But,, when developing a prototype i finf it useless to put effort in finish if the result was bad. In this case, result is really really good. but remember, i got longtube headers,ported heads,100cell cats, underdrive pulleys, 'needswings' bigger throttlebody(78mm) Now i feel the restrictions is in airmeter, and the 'knee', still oem, only mod here is no 'mesh' in airmeter and a small velocitystack inside the Y-pipe do guide air into airmeter.
0 2015/09/20 20:47:25
0 2015/09/27 10:59:31
0 2016/02/23 21:11:53
cut away the red marked. place bung at green marker. Not perfect measurements.
cut away the red marked. place bung at green marker. Not perfect measurements.
0 2016/03/20 02:06:40
pre made bung
pre made bung
0 2016/03/20 02:06:53
pre made bung
pre made bung
0 2016/03/20 02:06:59
0 2016/03/20 02:09:05
0 2016/03/22 05:37:23