MBWorld.org Forums
0 2024/10/19 13:35:27
0 2024/10/19 13:33:53
0 2024/06/30 07:02:23
Ready for the road..
Ready for the road..
0 2024/06/30 07:00:47
0 2024/06/30 07:00:20
0 2024/06/29 00:24:33
No more bolts left=ALL DONE!
No more bolts left=ALL DONE!
0 2024/06/29 00:24:00
0 2024/06/29 00:23:25
Flange bolt, instead of Torx.
Flange bolt, instead of Torx.
0 2024/06/29 00:22:57
R
R
0 2024/06/29 00:22:06
I swapped out the torx for flange bolts on both turbos. Flage bolts are just easier to work with.
I swapped out the torx for flange bolts on both turbos. Flage bolts are just easier to work with.
0 2024/06/28 22:35:13
Coming along fine.
Coming along fine.
0 2024/06/28 22:35:09
M6 x 16mm, 1.00 thread.
M6 x 16mm, 1.00 thread.
0 2024/06/28 22:35:04
Don't forget to plug any additional holeere c544⁴ 3;4p⁴4³³eee÷e44³3nj
Don't forget to plug any additional holeere c544⁴ 3;4p⁴4³³eee÷e44³3nj
0 2024/06/28 22:35:00
Don't forget to plug these outlets on the water pump.:
Don't forget to plug these outlets on the water pump.:
0 2024/06/28 22:34:56
0 2024/06/28 22:34:53
Before attempting to install the turbo end of the cooling lines, tuck a towel in the space below the lines, that way if you drop that bolt it doesn't fall into oblivion..
Before attempting to install the turbo end of the cooling lines, tuck a towel in the space below the lines, that way if you drop that bolt it doesn't fall into oblivion..
0 2024/06/28 22:34:49
0 2024/06/28 22:34:44
0 2024/06/28 22:34:37
I used 600 grit sand paper lubed with WD40 to remove any roughness on the gasket sealing area.
I used 600 grit sand paper lubed with WD40 to remove any roughness on the gasket sealing area.
0 2024/06/28 22:34:35
This is what I did to hold the gasket in place on the oil cooler for installation, get the bolts started then cut the old oring
This is what I did to hold the gasket in place on the oil cooler for installation, get the bolts started then cut the old oring
0 2024/06/26 20:10:49
Tapped with new pulley installed.
Tapped with new pulley installed.
0 2024/06/26 20:00:23
For this bolt that goe in the pulley behind the large driver side air intake.
For this bolt that goe in the pulley behind the large driver side air intake.
0 2024/06/26 20:00:20
M8 x 1.25 is the tap size, my tap depth was down till only 4 threads where showing on the tap.
M8 x 1.25 is the tap size, my tap depth was down till only 4 threads where showing on the tap.
0 2024/06/26 20:00:16
If you replace the oil filter housing, this pulley tower is not tapped on the new one.
If you replace the oil filter housing, this pulley tower is not tapped on the new one.
0 2024/06/26 20:00:13
0 2024/06/16 23:25:21
The old stuff.
The old stuff.
0 2024/06/16 23:14:40
0 2024/06/16 23:13:14
0 2024/06/16 23:11:50
0 2024/01/28 13:55:47
0 2024/01/27 08:41:31
0 2023/11/29 10:08:21
0 2023/10/20 18:47:32
0 2023/08/18 14:14:18
2010 XFR Pirelle's Stock.
2010 XFR Pirelle's Stock.
0 2023/08/18 14:14:14
0 2023/08/18 14:14:10
2014 S550 Michelin's stock.
2014 S550 Michelin's stock.
0 2023/08/18 14:14:05
2015 S63 Michelin's stock. Yes these are the same rims from my 2014.
2015 S63 Michelin's stock. Yes these are the same rims from my 2014.
0 2023/08/18 14:13:59
0 2023/07/08 04:16:38
My 2015 S63, at Los Angeles Cars and Coffee Mercedes-Benz meet.
My 2015 S63, at Los Angeles Cars and Coffee Mercedes-Benz meet.
0 2023/07/08 04:16:28