Air intake systems?
#1
Air intake systems?
Hey I'm looking for an intake system to put into my 04' c230k. I was wondering if anyone had any suggestions and if someone would tell me if this would fit my car http://www.engineperformancechip.com...ake-system-p-2
Also is there any chips I can put in my car?
Thanks
Also is there any chips I can put in my car?
Thanks
#5
#6
Senior Member
Join Date: Sep 2011
Location: SoCal
Posts: 274
Likes: 0
Received 0 Likes
on
0 Posts
Kompressor Sport Sedan 05 M271
im trying to make a custom intake as well
I want to make a straight shot from the right side inlet directly into the airbox
someone on here made one but i forgot where
I want to make a straight shot from the right side inlet directly into the airbox
someone on here made one but i forgot where
#7
Senior Member
Join Date: Jun 2011
Location: Lumberton, TX
Posts: 264
Likes: 0
Received 2 Likes
on
2 Posts
2009 ML350, 2007 GL450, 1963 GMC, BMW 325i
I made one. Still trying to tweak the fit a little.
![](http://i148.photobucket.com/albums/s30/HoggerRC/air6.jpg)
As for a chip, do a search for "Eurocharged ECU tune"
That should point you in the right direction.
![](http://i148.photobucket.com/albums/s30/HoggerRC/air6.jpg)
As for a chip, do a search for "Eurocharged ECU tune"
That should point you in the right direction.
Trending Topics
#11
MBWorld Fanatic!
Join Date: Feb 2009
Location: fort worth, tx
Posts: 5,054
Likes: 0
Received 10 Likes
on
8 Posts
06 C230 SS 6spd
Yea I just had issues with eurocharged not fully testing out the remote tune before launching it. Said it would work for my car but during our session it wouldn't so I had to overnight it to them so I could have it back at the beginning of the week. Other than that the tune is good.
#12
Senior Member
Join Date: Sep 2011
Location: SoCal
Posts: 274
Likes: 0
Received 0 Likes
on
0 Posts
Kompressor Sport Sedan 05 M271
#13
Senior Member
Join Date: Jun 2011
Location: Lumberton, TX
Posts: 264
Likes: 0
Received 2 Likes
on
2 Posts
2009 ML350, 2007 GL450, 1963 GMC, BMW 325i
It wasn't too bad. I just had to keep trimming the two plastic end pieces to get them down to the right size, while using foam to mock up the tube area and keep it all lined up, while making sure it was still going to be able to get it in place.
Then I wrapped it in multiple layers of fiberglass, a little bondo to smooth it out, another couple layers of fiberglass. Sand and paint.
The worst part is getting it in place. Since it's rigid something else has to give to get in place. The air box is too difficult to remove, so there was a lot of prying on the front plastic air scoop piece.
It could use a little more adjusting to get it snug into the air box opening, but it's got good direct air flow. And I want to wrap it in some carbon fiber.
Then I wrapped it in multiple layers of fiberglass, a little bondo to smooth it out, another couple layers of fiberglass. Sand and paint.
The worst part is getting it in place. Since it's rigid something else has to give to get in place. The air box is too difficult to remove, so there was a lot of prying on the front plastic air scoop piece.
It could use a little more adjusting to get it snug into the air box opening, but it's got good direct air flow. And I want to wrap it in some carbon fiber.
#14
Senior Member
Join Date: Sep 2011
Location: SoCal
Posts: 274
Likes: 0
Received 0 Likes
on
0 Posts
Kompressor Sport Sedan 05 M271
It wasn't too bad. I just had to keep trimming the two plastic end pieces to get them down to the right size, while using foam to mock up the tube area and keep it all lined up, while making sure it was still going to be able to get it in place.
Then I wrapped it in multiple layers of fiberglass, a little bondo to smooth it out, another couple layers of fiberglass. Sand and paint.
The worst part is getting it in place. Since it's rigid something else has to give to get in place. The air box is too difficult to remove, so there was a lot of prying on the front plastic air scoop piece.
It could use a little more adjusting to get it snug into the air box opening, but it's got good direct air flow. And I want to wrap it in some carbon fiber.
Then I wrapped it in multiple layers of fiberglass, a little bondo to smooth it out, another couple layers of fiberglass. Sand and paint.
The worst part is getting it in place. Since it's rigid something else has to give to get in place. The air box is too difficult to remove, so there was a lot of prying on the front plastic air scoop piece.
It could use a little more adjusting to get it snug into the air box opening, but it's got good direct air flow. And I want to wrap it in some carbon fiber.
#15
Senior Member
Join Date: Jun 2011
Location: Lumberton, TX
Posts: 264
Likes: 0
Received 2 Likes
on
2 Posts
2009 ML350, 2007 GL450, 1963 GMC, BMW 325i
Here it is as a rough mock up. I used the original connectors, but had to keep trimming to get the right fit.
The one vertical SC pipe was a bit of a pain to deal with. I ended up having to cut out a notch on the back of the intake, and re-glassing a small recessed channel to fit around the pipe.
![](http://i148.photobucket.com/albums/s30/HoggerRC/air3.jpg)
Here it is getting ready to be glassed.
The one vertical SC pipe was a bit of a pain to deal with. I ended up having to cut out a notch on the back of the intake, and re-glassing a small recessed channel to fit around the pipe.
![](http://i148.photobucket.com/albums/s30/HoggerRC/air3.jpg)
Here it is getting ready to be glassed.
![](http://i148.photobucket.com/albums/s30/HoggerRC/air4.jpg)