Yes. I work with a detailer at that shop and it is right across from the Fisker manufacturing building, so they bring all of their cars by to get it detailed/washed. I've seen so many of them, I don't even look twice at them anymore, haha.

 

The owner of this car came out to me in Orange County from the Los Angeles area to have me lightly smoke / tint the tail lights on his black Mercedes Benz CLK55. In addition to the tail lights I also smoked / tinted the headlights and the side blinkers on the mirrors of his car. This light smoke / tint shade is nice, because it is not too dark and won't block out too much of the light output from the head/tail lights. Also, since this film material has a gloss finish to it, it'll give a shine to your headlights or tail lights again if they are a bit dull from age/wear.

Before:


Tinted / smoked inner smaller passenger side headlight:


After:












-Don Nguyen

donathon@gmail.com

 

Had this new body black Mercedes Benz CLS63 come by to have me black out the chrome / aluminum trim around the windows and back rear trunk handle chrome piece. We went with matte black finish material so that the trim pieces still accented the car and did not disappear completely into the body of the car. You can notice it when I take the pictures, the trim pieces still pop out a little bit in the pictures. It gives it a nice contrast if that's what you are trying to go for. The owner of this car was also from Orange County.

By blacking out the chrome it really makes the red calipers and other parts of the car pop more.

Before:




After:










-Don Nguyen

donathon@gmail.com

 

The owner of this blue F10 BMW 550i contacted me to see if I could vinyl wrap the diffuser on his car with the 3M 1080 gloss carbon fiber material. He brought his car out to me in Orange County from around Riverside, for me do to the work on his car. Usually a lot of diffusers are not very practical to wrap due to their shapes/curves, which makes it hard for the vinyl to stick and stay conformed to over time. However, this one was fairly flat and there wasn't too much heat from around the exhaust areas on this car so that was a good thing as well.

Before:


After:










-Don Nguyen

donathon@gmail.com

 

The owner of this car wanted to have me wrap both the roof and the two side pillar pieces that run front the bottom of the front windshield to the back of the roof with my gloss black vinyl wrap material to give it the panoramic look. The gloss black vinyl wrap makes the roof continue and flow with the front/rear windshields pretty well. The owner of this car was from Irvine / Orange County also and brought his car over to me in Anaheim Hills to have the roof done. The tail lights were previously tinted / smoked by him beforehand, so that's not something I did.

Before:




After:















-Don Nguyen

donathon@gmail.com

 

I know I don't post this often, but I also do clear headlight film protection as well. I just never really take pictures of it, since you can never really see or tell the difference of a before and after

In this picture the driver side has already been done and the passenger side has been applied, just waiting to be trimmed. You can see everything is custom fitted, since I do not use pre cut materials. This allows me to cover more of the headlights than pre cut pieces do and also get a closer/better fit to the pieces that I am covering/applying the material to.

Clear headlight protective film is good if you have glass headlights, so it'll prevent rocks from cracking it or chipping it. This can also be applied to fog lights, which are more prone to cracking, since they're lower/closer to the ground. Even if your headlights are plastic, the film will help prevent nicks and chips in the plastic lenses. It'll also help protect/prevent against oxidation better. If your headlights are already oxidized/faded, I can clear/clean those up for you before putting on the clear film.





I know clear bras / clear headlight protection films aren't very exciting, so I figured I'd post pictures of this gray / silver Mercedes Benz E55 AMG's tail lights that I tinted as well. This is my lighter shade that I used for this cars tail lights. Unlike a lot of the other tail lights that I have posted recently, I only tinted the clear portions on this car's tail lights versus tinting the whole thing. So these pictures will be good to help show those who were interested in something similar for their cars and were wondering how just the clear portion would look like tinted / smoked, only slightly darkening the clear parts of the tail light.

Before:


After:


Before:


After:












-Don Nguyen

donathon@gmail.com

 

I think I work on more AMG cars than non AMG cars when it comes to Mercedes, haha. I blacked out the chrome / aluminum window trim on this black Mercedes Benz C63 AMG with my matte black vinyl material to give it the shadowline look. Owner came out to me in Orange County / Anaheim Hills to have the work done. I took some more detailed pictures of the corners and edges for those who were interested and asking me for them.

Before:






After:














-Don Nguyen

donathon@gmail.com

 

This gray / silver Mazda RX-8 came by to have me vinyl wrap the hood of his car with the 3M Di-Noc matte carbon fiber vinyl material to cover over his factory black hood that he had on there. The owner of this car drove up to me in Anaheim Hills / Orange County from San Diego county to have me do the vinyl work on his car. The weather was a bit over cast that day, so the carbon fiber weave in the vinyl did not stand out that much when photographed. From further away, the vinyl appears more of a solid flat/matte-ish and then when you get closer you start seeing the carbon fiber weaves in the vinyl.

As comparison, the eyelids on the headlights are real carbon fiber pieces.

Before:


After:












-Don Nguyen

donathon@gmail.com

 

These aren't the greatest pictures in the world, since I was in a bit of a rush when taking them. I wasn't going to use them, but it's not often that I get a domestic car, so I decided to just post them anyways. The owner of this red / orange Chevy Camaro came from Huntington Beach area out to me in Anaheim Hills to get the vinyl work done. He originally had a matte black vinyl roof installed on his car but he wanted to change the look up and get a gloss black roof put on there this time around.

Before (matte roof):




After (gloss roof):










-Don Nguyen

donathon@gmail.com

 

I had this newer 2012 or 2011 alpine white BMW E93 335i convertible come by for me to tint / smoke their tail lights and black out the chrome window trim (I'll post pictures of that process later). The owner of this car was from Irvine / Orange County and drove out to me in Anaheim Hills to get the vinyl work done. The tint / smoke film is very light and just slightly darkens the tail lights enough to give it a very factory look. It's light enough where you most likely won't get any hassle from cops about them. It's also light enough where if you put it on the headlights, fog lights, etc, it won't reduce the light output by that much compared to darker films.

Before:


Only driver side trunk tail light is tinted in this picture:


After:












-Don Nguyen

donathon@gmail.com

 

Took a while for the owner of this car and for me to figure/find out a time for him to be able to bring his car by to get the chrome / aluminum window trim wrapped in my gloss black vinyl material to give it that shadowline look. The owner of this car was from Los Angeles and brought his car out to me in Anaheim Hills / Orange County. He went with the gloss black over the matte black finish to get more of that factory BMW sport package look. I have seen cars come with the window trim in matte black as well, but I don't know what package those come with or are offered with.

Everything is wrapped seamlessly and tucked in where ever possible, to provide the longest lasting results.

Before:






After:










-Don Nguyen

donathon@gmail.com

 

I forgot to take the before pictures of this car before wrapping the roof, but you guys can probably imagine what it looked like before/stock with the white roof. The owner of this alpine white BMW E60 5 series came by to my shop in Anaheim Hills / Orange County from around Los Angeles to have the roof wrapped in my gloss black vinyl material. Went with the gloss black to give it a clean factory look, similar to what the car would have looked like if it came with a panoramic roof. Also took some close up pictures around the sunroof, edges, rails, etc for you guys to see the details that goes into my installs.

















-Don Nguyen

donathon@gmail.com

 

This Alpine White BMW E90 4-door 335i came by to have me vinyl wrap his chrome / brushed aluminum window trim with my matte black vinyl material. In addition to doing his window trim, I also wrapped his roof with the 3M di-noc matte carbon fiber finish to really set off the car. We had the antenna fin cover painted matte black, which went fairly well with the matte finish of the roof. The matte black window trim and matte roof also ties in together nicely. Also as a reference point, the trunk spoiler is real carbon fiber. From further away the carbon fiber finish looks more of a solid matte / flat black finish, but as you get closer to the car/roof, the carbon fiber weaves/design becomes more visible, which is also another nice subtle touch/look.















-Don Nguyen

donathon@gmail.com

 

ok, Since there is no possible way I can come over to Cali, can you give some tips on how to wrap around those crazy edges? Im a newb and wanna smoke all the chrome on my car...

 

Which edges are you referring to?

 

Even on a more stock-ish car, blacking out the chrome / aluminum window trim can change the dynamics of the car's looks greatly. It won't necessarily give it a modified/aftermarket look, but it definitely adds to the car's look, while still looking factory. The owner of this car drove out to me in Orange County / Anaheim Hills to get the wrap done. Everything is done seamlessly and in one piece to retain that factory look and without making it seem like a wrap job. We went with the matte black on this car to still give it some contrast and accent the trim pieces, instead of going with gloss black which would have made it kind of disappear into the car's black paint.

Before:






After:










-Don Nguyen

donathon@gmail.com

 

Emblems, a few trim pieces. And also, what smoke film do you use?

 

I don't wrap emblems. They're too small.

 

hmmm, ok, and as for the side trims, how do you work around sharp edges?

and what film do you use for smoke?

 

I sell the film for the lights if you're interested in purchasing some.

-Don

 

Ohhh, alright, cool. I'll be sure to check it out. But can you please give some advice on how to work around corners/edges?

 

It just wraps around. There is no trick to it really.

 

Seems like there are a lot of fans of wagons, so here are pictures of a blue E46 325i wagon / touring that I worked on recently. The owner of this car actually lived down the street from me in Irvine / Orange County, so I dropped by their house to do the vinyl wrap. The owner wanted me to black out his chrome / aluminum window trim. I went with the matte black to give it more of an aggressive look and it went well with all of the other matte black weather rubber pieces that lined the window trim and the overall look of the car.

Before:




After:








-Don Nguyen

donathon@gmail.com

 

Thanks for everyone who was able to make it out to me while I was up in norcal / Bay Area doing vinyl wraps. I only had one car that cancelled on me without any notice (which is a first out of all of my trips that I have been/gone up there), but other than that everything went good as usual.

This was one of the last cars that I did while up there, and I was a bit excited, so I forgot to take some before pictures of it. The owner of this white Subaru STI wagon / hatch brought his car to me to have me vinyl wrap the roof of his car with my gloss black vinyl material. Subarus are one of those cars that can pull off the matte or gloss black look. Since there is no sunroof on this car, it gives it a very smooth and continuous result / look.















-Don Nguyen

donathon@gmail.com

 

These aren't the best pictures in the world, since the owner of this car came later in the day and there was a lot of work that he wanted done on his car, so by the time I finished, it was already fairly late in the day. The owner of this car drove from San Diego up to me in Anaheim Hills / Orange County to get the vinyl work done. He wanted me to vinyl wrap his roof, roof spoiler, front splitters, side B pillars, and rear lower bumper diffuser all in the 3M di noc matte carbon fiber vinyl material finish. Personally, I do not like wrapping rear diffusers, but since the owner of this car was getting a lot of other work done, I decided to do it for him/his car.

Front splitters:


Roof spoiler:




Rear diffuser:




Roof:














Side pillars:


-Don Nguyen

donathon@gmail.com