Whats the weight of each part
#51
MBWorld Fanatic!
Join Date: Jun 2008
Location: Los Angeles
Posts: 8,060
Received 2,836 Likes
on
1,674 Posts
2012 P31 C63 Coupe Trackrat, 2019 GLE63S Coupe Beast
Holy
Henk. You're a madman.
![EEK!](https://mbworld.org/forums/images/smilies/eek.gif)
![thumbs](https://mbworld.org/forums/images/smilies/thumbsup.gif)
#52
Put some technocraft seats in ![Smilie](https://mbworld.org/forums/images/smilies/smile.gif)
![Smilie](https://mbworld.org/forums/images/smilies/smile.gif)
![Smilie](https://mbworld.org/forums/images/smilies/smile.gif)
![Smilie](https://mbworld.org/forums/images/smilies/smile.gif)
![Smilie](https://mbworld.org/forums/images/smilies/smile.gif)
![Smilie](https://mbworld.org/forums/images/smilies/smile.gif)
![Smilie](https://mbworld.org/forums/images/smilies/smile.gif)
The following users liked this post:
mr747 (11-12-2016)
#54
MBWorld Fanatic!
Join Date: Jun 2008
Location: Los Angeles
Posts: 8,060
Received 2,836 Likes
on
1,674 Posts
2012 P31 C63 Coupe Trackrat, 2019 GLE63S Coupe Beast
CF driveshaft?
The following users liked this post:
mr747 (11-12-2016)
#55
For sure cf drive shaft. I am gonna put a gearbox transaxle. Same setup as the sls. But its gonna be a sequential st6rt gearbox. Only way to get the weight distribution right.
The following users liked this post:
mr747 (11-12-2016)
#56
MBWorld Fanatic!
The following users liked this post:
mr747 (11-12-2016)
The following users liked this post:
mr747 (11-12-2016)
#58
MBWorld Fanatic!
#59
This is sick
#60
MBWorld Fanatic!
![EEK!](https://mbworld.org/forums/images/smilies/eek.gif)
Last edited by zcct04; 11-12-2016 at 06:04 PM.
The following users liked this post:
IBowlC63AMG (06-12-2017)
#61
Senior Member
Subscribed too. Always nice to see some extreme projects. Keep it up! Good luck and thanks for sharing!
#62
#63
Senior Member
#66
Senior Member
#71
Learning a lot about the electrical system and also how to bypass all airbags and pretensioners. Got all worked out. Cutting out now a ****load of wires.
Pulling ignition and fuel control out of the factory ecu so i get full control over fuel and timing ;-).
Pulling ignition and fuel control out of the factory ecu so i get full control over fuel and timing ;-).
#72
MBWorld Fanatic!
Frankly with the way the systems work together wiring may be the last thing I would yank out of there. It terrifies me cos there just seems to be no rhyme or reason to it sometimes, but maybe that's just my lack of knowledge.
#73
Its not the weight. But if you take all seats, all airbags and seatbelts out you get a ****load of errors on the dash. Even the annoying error when you fold down your rear Seats.
So i take out all access wires. And jump all wires so i have 0 error codes on the dash and tester.
So i take out all access wires. And jump all wires so i have 0 error codes on the dash and tester.
#74
MBWorld Fanatic!
![bow](https://mbworld.org/forums/images/smilies/bowdown.gif)
Soon my friend, you'll be the closest thing to an SLS for those of us that can't afford one
![drive](https://mbworld.org/forums/images/smilies/driving.gif)
You're very brave for shortening the wiring harness. It takes ***** of steel to do that to a Mercedes, which are known for being fussy with their electrics.