From stock c63 to 800HP
#1
Newbie
Thread Starter
From stock c63 to 800HP
Good day everyone, this is my first post in the form and I know it will be very interesting as I just beaten a Mclaren 650s and a moded Ferrari FF with my c63.
Like every other street racers we all are eager for more power and we will never be satisfied.
Let share my story and how far I have gone. I started with a Full IPE system for a yearlong then I decided to go for pp-performance tune along with BMC air filter.
Phase 1
Cart mods:
IPE full system
BMC air filter
PP-performance tune
Stock: 366whp
Mods: 466WHP/477RWTQ
Here in the middle east people are craving to race in the streets as we have huge roads with no pigs hovering around. I have raced an SRT8 with stroked engine 7.0L cams, ported heads and manifold. The guy got smoked easy (2nd gear hit rev limiter)
https://www.instagram.com/p/BLCarH-DRL4/?taken-by=c63sc
Later on I decided to go for a blower so I contacted WEISTEC for stage 2 as I was afraid to get stage 3 because it also requires the tranny upgrade as well.
I installed the blower myself at home with a help of a colleague. We had some minor issues but everything got fixed later on, we found that the MAP sensor extension cable was not tighten enough and I had all sorts of awkwardness when I put my foot on the gas.
Phase 2
Car mods:
IPE full system
BMC air filter
Stage 2 supercharger
Ice tank
Air/oil separator
WEISTEC spark plugs
Stock: 366WHP
Mods: 543WHP/ i don’t recall the WTQ
Guess what? I was shocked somehow as I was expecting much more power of what I felt inside the car.
I squeezed my mind on how to make extra power out of the same blower, so I decided to fabricate a smaller pulley as weistec are not offering any smaller size pulleys on stage 2.
I went from 57mm pulley to 50mm, car jumped from 543 to 577whp.
Still not satisfied yet!!!
Phase 3
Car mods:
IPE full system
BMC air filter
Stage 2 supercharger (50mm pulley)
Ice tank
Air/oil separator
WEISTEC spark plugs
Snowperformance stage 2 methanol kit
Boostane
Stock: 366WHP
Mods: 608WHP/575RWTQ
https://www.instagram.com/p/BLQNNpcDyN0/?taken-by=c63sc
Yaaa buddddyyyyyh, now we are talking, I was happy that I broke the 600whp boundaries. Car made 608WHP with 9psi , no tune was done on methanol or boostane. The stock tranny was holding all the power with no issues at all.
I drove the car for 2 months and then decided to go bigger ! yep I upgraded mine to stage 3 (gonnna fly)
I had to take the car to a shop to do the threads on the crank pulley for stage 3, I had to take the whole engine out so they can do it perfectly. First impression on stage 3 comparing to stage 2 was not promising as I was already in the 600 range. Boost was reading 10psi on stage 3 with the 67mm pulley.
I didn’t dyno the car on the stock pulley 67mm for stage 3, but I felt the tranny was NOT holding the power properly, I feel lag in shifting between gears. I knew by this that the car was making more power than what it had earlier.
A friend of mine decided to go for 60mm pulley on his s63 with same mods (bolt on meth etc…) we were afraid that the stock engine will not hold the power as we have poor gasoline quality in the middle east RON95. I raced couple cars then I was like “ lets try the 60mm pulley.”
Power level is SATISFYING!!!
Phase 4
IPE full system
BMC air filter
Stage 3 supercharger (60mm pulley)
Ice tank
Air/oil separator
WEISTEC spark plugs
Snowperformance stage 2 methanol kit
Boostane
Recaro seats 12kg for both front seats
Stock: 366WHP
Mods 60mm pulley: 651WHP/ 585RWTQ (tune was done on the 67mm pulley & tranny is slipping on the dyno & no meth was sprayed)
https://www.instagram.com/p/BOvK8A4DXnx/?taken-by=c63sc
I have done all the talking above lets watch some vids.
C63 VS Mclaren 650s
https://www.instagram.com/p/BOi3SwBDgDe/?taken-by=c63sc
C63 VS Ferrari FF (full exhaust system)
https://www.instagram.com/p/BOlIL91DaJr/?taken-by=c63sc
C63 VS Lambo Huracan (race fuel)
https://www.instagram.com/p/BOyBqGXhz9e/?taken-by=c63sc
C63 VS Mustang Roush Stage 3
https://www.instagram.com/p/BOjqXpEDCIU/?taken-by=c63sc
and more vids are in my IG: @C63sc
Problems:
My tranny couldn’t hold the power for stage 3 60mm pulley, after racing for 20 times I noticed the 4th and 5th gear slightly slipping, I also have a problem with boost which I had earlier on stage 2 and stage 3 now.
Boost only reads 5psi then suddenly it jumps to full boost. When I race, I had to start before the third honk so I can get full boost once they slam the gas.
Any suggestion to fix boost?
https://www.instagram.com/p/BO_f0IwhTJS/?taken-by=c63sc
Future plans:
I will be porting my heads and will be doing 3 angle cnc porting for the valves. Stay tuned am waiting for the tranny to arrive so I can travel to Kuwait for the cnc job as they do vacuum testing for the head and valves after they complete the work.
Stay tuned!!
I will be posting updates make sure you subscribe
Like every other street racers we all are eager for more power and we will never be satisfied.
Let share my story and how far I have gone. I started with a Full IPE system for a yearlong then I decided to go for pp-performance tune along with BMC air filter.
Phase 1
Cart mods:
IPE full system
BMC air filter
PP-performance tune
Stock: 366whp
Mods: 466WHP/477RWTQ
Here in the middle east people are craving to race in the streets as we have huge roads with no pigs hovering around. I have raced an SRT8 with stroked engine 7.0L cams, ported heads and manifold. The guy got smoked easy (2nd gear hit rev limiter)
https://www.instagram.com/p/BLCarH-DRL4/?taken-by=c63sc
Later on I decided to go for a blower so I contacted WEISTEC for stage 2 as I was afraid to get stage 3 because it also requires the tranny upgrade as well.
I installed the blower myself at home with a help of a colleague. We had some minor issues but everything got fixed later on, we found that the MAP sensor extension cable was not tighten enough and I had all sorts of awkwardness when I put my foot on the gas.
Phase 2
Car mods:
IPE full system
BMC air filter
Stage 2 supercharger
Ice tank
Air/oil separator
WEISTEC spark plugs
Stock: 366WHP
Mods: 543WHP/ i don’t recall the WTQ
Guess what? I was shocked somehow as I was expecting much more power of what I felt inside the car.
I squeezed my mind on how to make extra power out of the same blower, so I decided to fabricate a smaller pulley as weistec are not offering any smaller size pulleys on stage 2.
I went from 57mm pulley to 50mm, car jumped from 543 to 577whp.
Still not satisfied yet!!!
Phase 3
Car mods:
IPE full system
BMC air filter
Stage 2 supercharger (50mm pulley)
Ice tank
Air/oil separator
WEISTEC spark plugs
Snowperformance stage 2 methanol kit
Boostane
Stock: 366WHP
Mods: 608WHP/575RWTQ
https://www.instagram.com/p/BLQNNpcDyN0/?taken-by=c63sc
Yaaa buddddyyyyyh, now we are talking, I was happy that I broke the 600whp boundaries. Car made 608WHP with 9psi , no tune was done on methanol or boostane. The stock tranny was holding all the power with no issues at all.
I drove the car for 2 months and then decided to go bigger ! yep I upgraded mine to stage 3 (gonnna fly)
I had to take the car to a shop to do the threads on the crank pulley for stage 3, I had to take the whole engine out so they can do it perfectly. First impression on stage 3 comparing to stage 2 was not promising as I was already in the 600 range. Boost was reading 10psi on stage 3 with the 67mm pulley.
I didn’t dyno the car on the stock pulley 67mm for stage 3, but I felt the tranny was NOT holding the power properly, I feel lag in shifting between gears. I knew by this that the car was making more power than what it had earlier.
A friend of mine decided to go for 60mm pulley on his s63 with same mods (bolt on meth etc…) we were afraid that the stock engine will not hold the power as we have poor gasoline quality in the middle east RON95. I raced couple cars then I was like “ lets try the 60mm pulley.”
Power level is SATISFYING!!!
Phase 4
IPE full system
BMC air filter
Stage 3 supercharger (60mm pulley)
Ice tank
Air/oil separator
WEISTEC spark plugs
Snowperformance stage 2 methanol kit
Boostane
Recaro seats 12kg for both front seats
Stock: 366WHP
Mods 60mm pulley: 651WHP/ 585RWTQ (tune was done on the 67mm pulley & tranny is slipping on the dyno & no meth was sprayed)
https://www.instagram.com/p/BOvK8A4DXnx/?taken-by=c63sc
I have done all the talking above lets watch some vids.
C63 VS Mclaren 650s
https://www.instagram.com/p/BOi3SwBDgDe/?taken-by=c63sc
C63 VS Ferrari FF (full exhaust system)
https://www.instagram.com/p/BOlIL91DaJr/?taken-by=c63sc
C63 VS Lambo Huracan (race fuel)
https://www.instagram.com/p/BOyBqGXhz9e/?taken-by=c63sc
C63 VS Mustang Roush Stage 3
https://www.instagram.com/p/BOjqXpEDCIU/?taken-by=c63sc
and more vids are in my IG: @C63sc
Problems:
My tranny couldn’t hold the power for stage 3 60mm pulley, after racing for 20 times I noticed the 4th and 5th gear slightly slipping, I also have a problem with boost which I had earlier on stage 2 and stage 3 now.
Boost only reads 5psi then suddenly it jumps to full boost. When I race, I had to start before the third honk so I can get full boost once they slam the gas.
Any suggestion to fix boost?
https://www.instagram.com/p/BO_f0IwhTJS/?taken-by=c63sc
Future plans:
I will be porting my heads and will be doing 3 angle cnc porting for the valves. Stay tuned am waiting for the tranny to arrive so I can travel to Kuwait for the cnc job as they do vacuum testing for the head and valves after they complete the work.
Stay tuned!!
I will be posting updates make sure you subscribe
Last edited by C63sc; 01-09-2017 at 04:34 PM.
#2
beast bud and welcome
#4
MBWorld Fanatic!
I like these c63's builds/projects that have been popping up here... Good stuff
#7
MBWorld Fanatic!
Great car and vids! I think the most suprising one was the Lambo. Just race gas and a tune and that thing was a beast!
Trending Topics
#8
MBWorld Fanatic!
10 points for waving at the FF. Buhhhh bye.
But man I want a Huracan.
But man I want a Huracan.
#16
I'll bet you the price of the c63 with all these mods doesn't even come close to mclaren money if you ask me it's a total win taking down such a supercar
#17
Former Vendor of MBWorld
iTrader: (1)
Join Date: Oct 2016
Location: Georgia
Posts: 658
Received 232 Likes
on
136 Posts
2013 Mercedes C63 AMG
It doesn't seem like his car is dialed in correctly. I'm sure once he dials it in, fixes the transmission issue and correctly builds boost, the mclaren will be a walk in the park.
#19
Newbie
Thread Starter
#20
Newbie
Thread Starter
If we are comparing cost of both cars, including mods, AMG won in my book and was very satisfying. Not disappointed at all.
It doesn't seem like his car is dialed in correctly. I'm sure once he dials it in, fixes the transmission issue and correctly builds boost, the mclaren will be a walk in the park.
It doesn't seem like his car is dialed in correctly. I'm sure once he dials it in, fixes the transmission issue and correctly builds boost, the mclaren will be a walk in the park.
If you listen carfelly in the vids, in all races i had slipping issue in the transmission. If i get this fixed, trust me it will impress u
The following users liked this post:
Slow_c63 (01-11-2017)
#22
MBWorld Fanatic!
Join Date: Jan 2013
Location: Toronto, Canada
Posts: 3,726
Received 795 Likes
on
546 Posts
W204 C63 Coupe, W166 ML350 BlueTEC, 928GT, C5 Z06 & IS300 race cars, EQE 4Matic+ on order
It absolutely is an amazing build! It's just too bad that at the rate you're going you're likely going to die before the age of 30, and even worse that you could easily kill someone else that had nothign to do with your idiotic choice to race on public roads. Is there someone that you would like us top notify when you receive the Darwin award?
#23
MBWorld Fanatic!
Join Date: Jun 2008
Location: Los Angeles
Posts: 8,063
Received 2,845 Likes
on
1,678 Posts
2012 P31 C63 Coupe Trackrat, 2019 GLE63S Coupe Beast
It absolutely is an amazing build! It's just too bad that at the rate you're going you're likely going to die before the age of 30, and even worse that you could easily kill someone else that had nothign to do with your idiotic choice to race on public roads. Is there someone that you would like us top notify when you receive the Darwin award?
#25
Member
Follow you on IG.
Your car runs extremely well.
We all gonna die some day
Your car runs extremely well.
It absolutely is an amazing build! It's just too bad that at the rate you're going you're likely going to die before the age of 30, and even worse that you could easily kill someone else that had nothign to do with your idiotic choice to race on public roads. Is there someone that you would like us top notify when you receive the Darwin award?