W208 How To's
#151
Newbie
Park light
You can look it up here: http://www.sylvania.com/ConsumerProd...lacementGuide/
I recently changed into LED 64132. They look great but they give out an error(even if ebay advertised it as no error)
#152
If those are your park lights, you should Be using 64132.
You can look it up here: http://www.sylvania.com/ConsumerProd...lacementGuide/
I recently changed into LED 64132. They look great but they give out an error(even if ebay advertised it as no error)
You can look it up here: http://www.sylvania.com/ConsumerProd...lacementGuide/
I recently changed into LED 64132. They look great but they give out an error(even if ebay advertised it as no error)
But the issue isn't the light itself being blown or not working, i tested it on the passenger side parking light and it works fine. But i think i may have blown the fuse attached to the wiring harness that the light plugs into on the driver side. Is this something that can happen? and can i fix this?
Last edited by Stumbling Corgi; 09-30-2011 at 01:42 AM.
#153
Junior Member
Join Date: Oct 2010
Location: Phoenix
Posts: 51
Likes: 0
Received 1 Like
on
1 Post
'99 CLK 320 Cabriolet
just replaced the voltage regulator on my 99 320:
https://mbworld.org/forums/clk-class...ml#post4906648
https://mbworld.org/forums/clk-class...ml#post4906648
#154
Junior Member
Join Date: Dec 2008
Location: Seattle, Wa.
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
2002 CLK430
LCA removal
Is there a write up for removing the lower control arms. I ordered some polyurethane bushings and I would like to remove the arms and bring them to a shop to get the bushings in. Any help appreciated
#155
Fuel level not correct for MB CLK 320 2001
Hello All, I am glad that we have this kind of Questions and fast asnwer from MBWorld. My proplem that my fuel tank is full but the level front of the driver side is not reading it, its going up and down and once i start the car it showe its empty completly could you please advice me what I have to do, some adivce me that the fuel level sensor, I can not find it and I dont know if its the problem from it. could you please give me what I have to do my car is MB CLK 320 model 2001 by the way my car is for GCC waiting your reply soon
#157
Super Member
What do you mean by "GCC"?
Hello All, I am glad that we have this kind of Questions and fast asnwer from MBWorld. My proplem that my fuel tank is full but the level front of the driver side is not reading it, its going up and down and once i start the car it showe its empty completly could you please advice me what I have to do, some adivce me that the fuel level sensor, I can not find it and I dont know if its the problem from it. could you please give me what I have to do my car is MB CLK 320 model 2001 by the way my car is for GCC waiting your reply soon
#161
Twin Ther Not Working
Hi all . I have a 1999 CLK 230 Kompressor which has been a great car up until now . The car gets hot in traffic ( idle) and the twin fans on the front where the black plastic grill is are not engadging at all . My AC works fine and all settings on my climate control seem fine . Also the clutch fan on the engine seems to be spinning quite loose? As in it looks like i could stop it with my hand sort of like its slipping ? Even when warm the fan doesnt seem to be spinning strong and tight . Has anyone had this problem ? Can someone help me .
#162
Newbie
Join Date: Jun 2007
Location: Johannesburg, South Africa
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
2001 CLK320, 2000 SL320 V6
Fuel gauge level
When you fill up with petrol ensure the ignition switch key is removed. Also ensure you use a good quality high octane fuel. These cars work in strange ways.
#163
MBWorld Fanatic!
Join Date: Nov 2001
Location: Georgia
Posts: 2,619
Likes: 0
Received 51 Likes
on
41 Posts
E 63S Wagon Renntech, E55 Renntech, SL65, SL 55 030, ML, bunch of old ones--they come, they go...
Rear seat removal ,cabriolet..
Mainly I just want to get the seat bottom out for cleaning/treating...thanks
#164
Senior Member
Replace Exhaust Manifolds/Install Short-Tube Headers
I did this on my w208 clk55; it may be slightly different on the 320, but I believe it's identical on the 430.
You'll need:
- new headers/manifolds
- 8 exhaust manifold gaskets
- some extra 6mm studs and nuts
- rust penetrating spray
- various tools (10mm socket, 10mm box wrench, 13mm socket, swivel bit, long extension, tools to remove coil packs and plug wires)
Instructions:
- jack up the car as high as possible
- disconnect battery
- remove 2 nuts securing the brake fluid reservoir, and move aside
- remove 1 plastic nut securing washer fluid reservoir. Remove two hoses on top, and two wires (one on top and one towards the bottom on the front). Move aside (no need to drain fluid from either tank)
- remove air cleaner assembly, spark plug wires, and coil packs. Cover MAF with rag
- liberally coat all 16 exhaust manifold nuts and 4 catalytic converter bolts with rust penetrating spray, and allow to soak
- remove 4 catalytic converter bolts (13mm) from under car
- remove 16 manifold nuts (10mm). It may be too tight to get a socket on some, so you may need to use something else (I used a box wrench)
- remove manifolds and old gaskets
- install new gaskets and manifolds/headers and loosely thread nuts onto studs (if any of the studs came out of the head, they must be threaded back in before putting the nut on)
- tighten nuts to 20Nm (I couldn't fit my torque wrench so I just went pretty snug). IMPORTANT: Start at the rear and work forward to ensure proper seal
- bolt cats to new headers/manifolds using the same 13mm bolts
- replace everything you removed (coil packs + plug wires, 2 fluid reservoirs, and air cleaner assembly)
- lower car and reconnect battery
You'll need:
- new headers/manifolds
- 8 exhaust manifold gaskets
- some extra 6mm studs and nuts
- rust penetrating spray
- various tools (10mm socket, 10mm box wrench, 13mm socket, swivel bit, long extension, tools to remove coil packs and plug wires)
Instructions:
- jack up the car as high as possible
- disconnect battery
- remove 2 nuts securing the brake fluid reservoir, and move aside
- remove 1 plastic nut securing washer fluid reservoir. Remove two hoses on top, and two wires (one on top and one towards the bottom on the front). Move aside (no need to drain fluid from either tank)
- remove air cleaner assembly, spark plug wires, and coil packs. Cover MAF with rag
- liberally coat all 16 exhaust manifold nuts and 4 catalytic converter bolts with rust penetrating spray, and allow to soak
- remove 4 catalytic converter bolts (13mm) from under car
- remove 16 manifold nuts (10mm). It may be too tight to get a socket on some, so you may need to use something else (I used a box wrench)
- remove manifolds and old gaskets
- install new gaskets and manifolds/headers and loosely thread nuts onto studs (if any of the studs came out of the head, they must be threaded back in before putting the nut on)
- tighten nuts to 20Nm (I couldn't fit my torque wrench so I just went pretty snug). IMPORTANT: Start at the rear and work forward to ensure proper seal
- bolt cats to new headers/manifolds using the same 13mm bolts
- replace everything you removed (coil packs + plug wires, 2 fluid reservoirs, and air cleaner assembly)
- lower car and reconnect battery
Last edited by njgilligan; 02-20-2012 at 12:19 PM.
#167
Senior Member
I know there's a post on here about it with more detail and pictures...
There are two tabs on the cluster, one on the left, and one on the right. Get two credit cards or something similar and slide them between the dash and instrument cluster on the sides. You have to get between the tabs and the dash. Then just pull out with your hands on the side of the cluster.
There are two tabs on the cluster, one on the left, and one on the right. Get two credit cards or something similar and slide them between the dash and instrument cluster on the sides. You have to get between the tabs and the dash. Then just pull out with your hands on the side of the cluster.
#169
Junior Member
Join Date: Mar 2012
Location: Perth, Australia
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
clk 230 w208
Display cluster clk203 w208
I know there's a post on here about it with more detail and pictures...
There are two tabs on the cluster, one on the left, and one on the right. Get two credit cards or something similar and slide them between the dash and instrument cluster on the sides. You have to get between the tabs and the dash. Then just pull out with your hands on the side of the cluster.
There are two tabs on the cluster, one on the left, and one on the right. Get two credit cards or something similar and slide them between the dash and instrument cluster on the sides. You have to get between the tabs and the dash. Then just pull out with your hands on the side of the cluster.
Yep found the post I need to buy some tools. I've attatched the pdf.
Hopefully the dispay will arrive this week. Loving this car.........................
#170
CLK 320 Windows
does anyone know a fix for my problem the windows on my coupe do not drop when you close the doors leaving the top of the glass outside of the rubber. Thanks
#171
door stops
Does anyone have pictures of door stop on drivers side of 1998 clk320. and instructions on how to replace and where I can get the stops and how hard it is to replace? Pictures would be great also!
Also, when you adjust your windows(specifically drivers side) down do you turn the screw clockwise or counterclockwise.
Thanks, all help is much appreciated!
Also, when you adjust your windows(specifically drivers side) down do you turn the screw clockwise or counterclockwise.
Thanks, all help is much appreciated!
![Thankyou](https://mbworld.org/forums/images/smilies/thankyou.gif)
#172
Super Member
Join Date: Apr 2012
Posts: 840
Likes: 0
Received 0 Likes
on
0 Posts
Blown 208 55 amg, 211 55 amg
#174
Junior Member
Join Date: Jun 2012
Location: Kingston Jamaica
Posts: 21
Likes: 0
Received 2 Likes
on
1 Post
1999 CLK 230K
Can anyone on the forum HELP me resolve this please...i drive a 1999 CLK Cab and when i hit a pot hole or the road surface gets really rough and uneven. or i go over a speed bump too fast..ALL 4 windows roll down at the sametime and the convertible light flashes...Using the A/C is now pointless...Has anyone ever experienced this?
#175
Member
Join Date: Feb 2008
Location: FL 33325
Posts: 214
Likes: 0
Received 0 Likes
on
0 Posts
2002 CLK 430
how to remove long wood trim top of dash ?
how to remove long wood trim top of dash ? we have total (w208) of 9 piece
wood trims, i wanna cover it with CF
plz any help
wood trims, i wanna cover it with CF
plz any help
![smash](https://mbworld.org/forums/images/smilies/smashfreak.gif)
Last edited by J56BP; 07-15-2012 at 05:09 AM.