Official W213 Picture Thread
The following 4 users liked this post by suby01:
#479
The following users liked this post:
M. Schneider (10-27-2022)
#480
Super Member
Thanks. Drilling is suggested, as it comes with places for them every 4-6 inches but that seems a bit too excessive. There are several ways you can do this, drill only, 3M double sided tape only, or use epoxy type glue, or a combination of any of the three. I used only 2 screws kind of in the middle points and then 3M double sided tape. And the lip simply slides onto your bottom bumper like a C shape kind of, this is where I used 3M double sided tape if I ever decide to remove the lip then I can remove the screws, no one will never see those that they are there since they are under the bumper, and there shouldnt be much scratches on the bumper from the lip touching the lip due to the cushion of the tape. In my previous car I used epoxy glue and it worked great also but that was more of a permanent type install. It was already rain and wind tested and holds without budging.
The following users liked this post:
BF3PDZ (01-20-2019)
The following users liked this post:
M. Schneider (10-27-2022)
The following 2 users liked this post by Clear2Close:
M. Schneider (10-27-2022),
rbrylaw (02-03-2019)
#486
#487
Junior Member
#488
Super Member
Nothing else at this time. The Brabus modifications are a little too extreme with other accessories. But I did love the front lip. I initially went with a CF option from another brand but I decided that I want to keep the theme gloss black instead.
The following 2 users liked this post by jojot:
CarFan1 (11-24-2022),
M. Schneider (10-27-2022)
#491
Super Member
Bumping this thread up. Cmon everyone snap some pictures of your W213's!
From clean to dirty. Stock to modified. Snow outside to palm trees. At work or grocery store or fancy instagram photo op spot. Lets keep this going.
From clean to dirty. Stock to modified. Snow outside to palm trees. At work or grocery store or fancy instagram photo op spot. Lets keep this going.
The following users liked this post:
AB550 (08-10-2019)
The following 3 users liked this post by mdot949:
The following users liked this post:
M. Schneider (10-27-2022)
The following users liked this post:
threeMBs (03-08-2019)
#497
MBWorld Fanatic!
Amazing, 20x9.5 et20 upfront! I tried 20x8.5 et18 and poke was about 12mm. With your setup, my poke would be a full inch. Two differences - you're lowered, I'm not; E43 vs. E450 (however, to my knowledge, unlike E63, all fenders are identical between E53/43/450/400/300). The only reasonable conclusion is: lowering allows for significantly lower offsets, which otherwise would be impossible.
#498
Member
iTrader: (1)
Amazing, 20x9.5 et20 upfront! I tried 20x8.5 et18 and poke was about 12mm. With your setup, my poke would be a full inch. Two differences - you're lowered, I'm not; E43 vs. E450 (however, to my knowledge, unlike E63, all fenders are identical between E53/43/450/400/300). The only reasonable conclusion is: lowering allows for significantly lower offsets, which otherwise would be impossible.
#499
SPONSOR
Join Date: Jan 2005
Location: MIAMI, FL
Posts: 2,395
Received 243 Likes
on
189 Posts
www.wheelsboutique.com
ANRKY AN28's in 21"x9.5" || 21"x10.5"
Custom built to order, no spacers needed.
More photos at - https://wheelsboutique.com/gallery/m...-on-ANRKY-AN28
Custom built to order, no spacers needed.
More photos at - https://wheelsboutique.com/gallery/m...-on-ANRKY-AN28
The following users liked this post:
AB550 (08-10-2019)