Camshaft Solenoid Recall for W221
#26
Junior Member
Join Date: Mar 2011
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
'10 E350, '03 Excursion 7.3 PSD
No need to fret folks...the campaign (not recall) will cover every m272 & m273 engine built. Each engine requires 4 wiring pig tails and there's no way the dealer, parts distribution network & supplier can handle that many vehicle's at once. The solution is to release the campain to a group of vin #'s at a time over a few months.
#27
Member
Join Date: Jul 2012
Location: Long Island, NY
Posts: 124
Received 0 Likes
on
0 Posts
2014 GL 450
#28
Member
Join Date: Jul 2012
Location: Long Island, NY
Posts: 124
Received 0 Likes
on
0 Posts
2014 GL 450
No need to fret folks...the campaign (not recall) will cover every m272 & m273 engine built. Each engine requires 4 wiring pig tails and there's no way the dealer, parts distribution network & supplier can handle that many vehicle's at once. The solution is to release the campain to a group of vin #'s at a time over a few months.
#31
Member
I checked mine. Pulled out one by one and one of them has oil inside the socket
There is no leak out to the outside socket and no check engine code yet. Will check with dealer for recall or I'll replace it myself.
![Wink](https://mbworld.org/forums/images/smilies/wink.gif)
There is no leak out to the outside socket and no check engine code yet. Will check with dealer for recall or I'll replace it myself.
Last edited by mb1000; 09-27-2012 at 09:54 PM.
#32
Senior Member
Join Date: Jul 2010
Location: Wisconsin
Posts: 386
Likes: 0
Received 3 Likes
on
3 Posts
2007 S550V4 2001 S430 (Sold) 1976 450 SL
The SA @ my Wisconson dlrshp. emailed back to my query, precipitated by board discussion, that my S-550, a 2007, with production # 117,123 is not effected by this recall. Leap of faith, but I am not pursuing. Is there a production # where it is applicable?
#33
Called my local deal (Atlanta) and they confirmed there is recall for my VIN. This is a pity 'cos I just changed 3 camshafts myself about 2 weeks ago - will be replacing all 4 again at the dealer next week.
$75.00 + time wasted!!
$75.00 + time wasted!!
#35
Member
Checked with my dealer and there is a recall to my car. My VIN is *103159 and covered by the recall . SA told me that MB is still sending out recall mail to owners.
#37
Good day Gents. Could you answer my question. Looks like I have a problem with camshaft solenoids I have read "M272 timing error" file and seems to be in "Scenario 2" (SD gives fault codes 0060 and 0064). My question is, is it dangerous for the engine when solenoids are faulty? Thanks for reply.
#38
Member
![Wink](https://mbworld.org/forums/images/smilies/wink.gif)
Instead of replacing 4 solenoids, they just added an extension cord
(with better rubber seal on the connector) each and plug the oil leaking from solenoid. In 30min, my car was ready.
I'll replace solenoids myself.
#39
hello everyone, I have the same problem with my 2003 c230 k, after having dealership replaced the solenoid harness, i replaced the solenoid but noticed that there's no seal between these 2 surfaces where the solenoid seats against the cam front cover, allowing oil to leak thru there. Does any one knows if this is an engineering flaw from MB? i asked SA guys and they said there's no seal in between. have any one here have this stubborn oil leak after all this work has been done? i forgot to say that i also replaced the middle oil plug in the new solenoid...any ideas how to re-invent their design????
#40
Out Of Control!!
Join Date: Jul 2003
Location: North Scottsdale, AZ
Posts: 15,903
Received 4,440 Likes
on
3,153 Posts
'71 Pinto
#41
I check in for oil change today on my 07 s550 out of warranty :-)
My service advisor informs me about the open campaign for our w221.
They replaced cam sensor/wires at no charge. Also, SDS lowering is done too :-)
Ned
My service advisor informs me about the open campaign for our w221.
They replaced cam sensor/wires at no charge. Also, SDS lowering is done too :-)
Ned
#43
Out Of Control!!
Join Date: Jul 2003
Location: North Scottsdale, AZ
Posts: 15,903
Received 4,440 Likes
on
3,153 Posts
'71 Pinto
Service Campaign Bulletin
#44
thank you for the PDF
I went to a MB workshop and they checked my car there was an errors
looks please at the photo i guess is the same issue here, but the workshop said we have to take the engine out and woking on it takes 7 days !!
i'm totally surprised of that 7 days with no car !! also, there is no faulty symptoms while driving the car except the engine light is on !!
please help me to figure out the issue as it shown in the photo here with its codes ..
thank you
![](http://www10.0zz0.com/2013/08/13/20/319309374.png)