How do you replace the upper control arm?
Thread Starter
Junior Member
Joined: Jul 2012
Posts: 71
Likes: 0
E430
How do you replace the upper control arm?
How do you replace the upper control arm on a 06 E55? Ive got mad clunking and squeaking and I cant find anything that has any info on replacing the upper control arms...
Junior Member
Joined: Jun 2015
Posts: 41
Likes: 1
From: Long Island, NY
former 2006 CLS55 AMG owner (124k miles)
http://www.mercedesmedic.com/diy-how...m-e-cls-class/
Senior Member
Joined: Apr 2015
Posts: 354
Likes: 32
04 E55 AMG
Very easy just screw the three bolts on top and the lower bolt in on the bottom. Don't forget to use loctite.
Use a ball joint separator instead of a pickle fork. Also probably better to take off the tire and check your other joints to see what else may need to be changed.
Trending Topics
Thread Starter
Junior Member
Joined: Jul 2012
Posts: 71
Likes: 0
E430
Ended up getting everything apart on the driver side and couldn't get the control arm out because of those damn nuts that spin in the engine compartment. Why in the world are not those welded in? Their was no room for me to get anything down there to hold them from spinning. Especially on the firewall side! Put it all back together and accomplished nothing.
MB World Stories
The Best of Mercedes & AMG
8 Oddball Mercedes Ideas That Actually Made it to Production
Verdad Gallardo
Dubai Tuner Gives the Mercedes G-Class An Entirely New Look
Verdad Gallardo
Six Gift Ideas Your AMG Loving Dad or Grad Will Cherish
7 Craziest Things AMG Gas Ever Built
Verdad Gallardo
New Electric Mercedes-AMG GT 4-Door Coupe Unveiled: 10 Things You Need to Know
Verdad Gallardo
6 Mercedes Models That Did NOT Age Well (But Are Somehow Still Cool)
Verdad Gallardo
Manual Mercedes? 6 Times Sindelfingen Let Drivers Have All The Fun
Verdad Gallardo
Mercedes SLR McLaren 722 S Is Extremely Rare Example Modified by McLaren
Verdad Gallardo
8 Classic Boxy Mercedes Designs That Have Aged Like Fine Wine
Verdad Gallardo
Member
Joined: Jun 2010
Posts: 84
Likes: 8
From: South Jersey
2010 E63AMG
Ended up getting everything apart on the driver side and couldn't get the control arm out because of those damn nuts that spin in the engine compartment. Why in the world are not those welded in? Their was no room for me to get anything down there to hold them from spinning. Especially on the firewall side! Put it all back together and accomplished nothing.
and these cars are sometimes challenging to work on. My suggestion would be to separate the upper control arm ball joint and wiggle the control arm by hand. If it squeaks than it is the upper control arm bushing and if you can't remove it spray it with some grease/motorcycle chain lube or something similar. If it is clunking or it feels like the bushing is shot than it needs to come out. Search the posts on front end clunking and there are some long discussions on this with grease options. If there is no noise i would change out the ball joint. Gjunion has it pictured above, 3 bolts on the end of the upper control arm and off it goes. Install a new one (with loctite as suggested) and at least that can be eliminated from the list of possible problems. Harbor freight has a front end kit that has all of the tools you need to separate the ball joint and reassemble. It is not the nice hardened steel separator he has in the picture but it will work a few times before it yields...step by step you can make progress here. Good luck.
Thread Starter
Junior Member
Joined: Jul 2012
Posts: 71
Likes: 0
E430
Ya, Ive already replaced the upper ball joint and forward control arm but not the lower control. In all actually its most likely not the upper arm, but I happen to have it laying around. I have a new sway bar end link also. I may just swap that out considering its so simple.
