MBWorld.org Forums
Use a T25 driver to remove screws.
Use a T25 driver to remove screws.
0 2016/01/19 21:07:04
Use a flat head screwdriver to loosen clamps on both sides.
Use a flat head screwdriver to loosen clamps on both sides.
0 2016/01/19 21:07:05
Pull up and wiggle the lid toward you gently til it comes loose.
Pull up and wiggle the lid toward you gently til it comes loose.
0 2016/01/19 21:07:06
Flip the lid upside down to gain access to the MAF plug. Use a flat head screwdriver to release the clip. DO NOT PULL FROM THE WIRE. You can wedge the driver on either side of the MAF to safely guide the plug off. When you do this on the other side, the same clip is on the TOP of the MAF.
Flip the lid upside down to gain access to the MAF plug. Use a flat head screwdriver to release the clip. DO NOT PULL FROM THE WIRE. You can wedge the driver on either side of the MAF to safely guide the plug off. When you do this on the other side, the same clip is on the TOP of the MAF.
0 2016/01/19 21:07:07
OEM vs. ROW
OEM vs. ROW
0 2016/01/19 21:07:08
Don't forget to pull this shroud off the MAF.
Don't forget to pull this shroud off the MAF.
0 2016/01/19 21:07:09
Remove old filter on both sides. It doesn't hurt to clean the tray too before inserting the new filter.
Remove old filter on both sides. It doesn't hurt to clean the tray too before inserting the new filter.
0 2016/01/19 21:07:10
Rest the new filter in place. I used an AFE Pro Dry S filter.
Rest the new filter in place. I used an AFE Pro Dry S filter.
0 2016/01/19 21:07:11
Plug the MAF into the ROW box. Make sure it's engaged.
Plug the MAF into the ROW box. Make sure it's engaged.
0 2016/01/19 21:07:12
Put MAF cover back on and screw the lid back on. You may need to insert the lid back into the tube housing FIRST before completely seating the air filter as not to crush it.
Put MAF cover back on and screw the lid back on. You may need to insert the lid back into the tube housing FIRST before completely seating the air filter as not to crush it.
0 2016/01/19 21:07:13
Also check the lid to see if any metal clips are still on them. Pull them off and put them back on the front panel or place them in the corresponding slots on the ROW box lids.
Also check the lid to see if any metal clips are still on them. Pull them off and put them back on the front panel or place them in the corresponding slots on the ROW box lids.
0 2016/01/19 21:07:14
Rest new filter in place.
Rest new filter in place.
0 2016/01/19 21:07:15
Insert ROW box into tube housing as shown. Again, the air filter may need to be moved in order to seat the ROW box in properly.
Insert ROW box into tube housing as shown. Again, the air filter may need to be moved in order to seat the ROW box in properly.
0 2016/01/19 21:07:16
Plug MAF back in.
Plug MAF back in.
0 2016/01/19 21:07:17
Put MAF cover back on and screw lid back on. Re-attach front panel and re-connect your battery. Install complete! This should take you about 15-20 mins, just enough time for the TCU to be reset!
Put MAF cover back on and screw lid back on. Re-attach front panel and re-connect your battery. Install complete! This should take you about 15-20 mins, just enough time for the TCU to be reset!
0 2016/01/19 21:07:17
0 2016/01/27 20:35:58
0 2016/01/27 20:51:43
0 2016/01/27 21:02:08
0 2016/01/27 21:26:52
0 2016/01/27 22:18:14
0 2016/01/29 21:47:40
0 2016/01/29 22:19:50
0 2016/01/30 14:54:02
0 2016/02/01 07:36:04
0 2016/02/01 07:36:30
0 2016/02/04 21:15:49
0 2016/02/04 21:22:07
0 2016/02/08 21:05:06
0 2016/02/10 19:49:23
0 2016/02/10 19:49:38
0 2016/02/10 19:49:47
0 2016/02/10 19:49:52
0 2016/02/10 19:49:55
0 2016/02/10 19:49:59
0 2016/02/12 15:30:18
0 2016/02/18 15:52:47
0 2016/02/19 07:18:09
0 2016/02/19 07:18:20
0 2016/02/19 07:20:41
0 2016/02/19 18:45:34