MBWorld.org Forums
0 2015/07/15 21:55:03
Fill with oil and then close with oil cap.
Fill with oil and then close with oil cap.
0 2015/07/15 21:55:06
Lift off engine cover.
Lift off engine cover.
0 2015/07/15 21:55:07
El Fin! Err... Woof!
El Fin! Err... Woof!
0 2015/07/15 21:55:08
You'll need 7-8 Quarts of European Spec 0W-40 motor oil, oil filter, 32mm socket, 17mm socket, Mityvac MV7201. Dog not included
You'll need 7-8 Quarts of European Spec 0W-40 motor oil, oil filter, 32mm socket, 17mm socket, Mityvac MV7201. Dog not included
0 2015/07/15 21:55:10
I got this off of Sears website for a little less than $90.
I got this off of Sears website for a little less than $90.
0 2015/07/15 21:55:11
0 2015/07/15 21:55:12
0 2015/07/15 21:55:14
0 2015/07/15 21:55:15
Mmmmm, tasty
Mmmmm, tasty
0 2015/07/15 21:55:17
There are six clips underneath (location shown in orange circles) you need to release in order to get this portion of the engine cover off.
There are six clips underneath (location shown in orange circles) you need to release in order to get this portion of the engine cover off.
0 2015/07/15 21:55:21
Start by releasing the front set of clips.
Start by releasing the front set of clips.
0 2015/07/15 21:55:29
0 2015/07/15 21:55:31
Move to one side and release clips.
Move to one side and release clips.
0 2015/07/15 21:55:32
Complete by releasing opposite side of clips.
Complete by releasing opposite side of clips.
0 2015/07/15 21:55:33
You will need the 32mm socket for the oil filter cap and a 17mm socket to loosen the oil cap.
You will need the 32mm socket for the oil filter cap and a 17mm socket to loosen the oil cap.
0 2015/07/15 21:55:34
Remove dipstick
Remove dipstick
0 2015/07/15 21:55:35
Loosen the oil cap with 17mm socket if needed. Removal of oil cap is important to improve flow.
Loosen the oil cap with 17mm socket if needed. Removal of oil cap is important to improve flow.
0 2015/07/15 21:55:44
Start by inserting larger tube into blue ringed inlet as shown.
Start by inserting larger tube into blue ringed inlet as shown.
0 2015/07/15 21:55:45
Remember to close the top!
Remember to close the top!
0 2015/07/15 21:55:47
Attach smaller tube to larger tube via connector as shown.
Attach smaller tube to larger tube via connector as shown.
0 2015/07/15 21:55:48
Make sure this is pushed down to insure that it is on suction.
Make sure this is pushed down to insure that it is on suction.
0 2015/07/15 21:55:49
Insert dipstick
Insert dipstick
0 2015/07/15 21:55:50
Insert tube of Mityvac into the shaft of the oil dipstick. Be sure to push all the way down until you no longer push down.
Insert tube of Mityvac into the shaft of the oil dipstick. Be sure to push all the way down until you no longer push down.
0 2015/07/15 21:55:51
Pump a few times to start flow and pump periodically to continue flow.
Pump a few times to start flow and pump periodically to continue flow.
0 2015/07/15 21:55:53
If using the MV7201, you should have removed about this much oil from the crankcase.
If using the MV7201, you should have removed about this much oil from the crankcase.
0 2015/07/15 21:55:55
Remove tube from dipstick shaft.
Remove tube from dipstick shaft.
0 2015/07/15 21:55:56
Insert tube in a container in which you plan to store the old oil.
Insert tube in a container in which you plan to store the old oil.
0 2015/07/15 21:55:57
Reverse flow of pump by pushing up. Pump a few times so it will output old oil into container. While this is going on, continue with the oil change and checking flow periodically.
Reverse flow of pump by pushing up. Pump a few times so it will output old oil into container. While this is going on, continue with the oil change and checking flow periodically.
0 2015/07/15 21:55:59
Use 32mm socket to loosen oil filter cap.
Use 32mm socket to loosen oil filter cap.
0 2015/07/15 21:56:01
Screw oil filter back onto vehicle. tighten by hand and then 25nM with a torque wrench
Screw oil filter back onto vehicle. tighten by hand and then 25nM with a torque wrench
0 2015/07/15 21:56:03
Remove oil filter cap
Remove oil filter cap
0 2015/07/15 21:56:04
0 2015/11/27 17:00:02
0 2015/11/27 17:00:04
0 2015/12/26 22:52:55
0 2016/01/05 15:01:13
0 2016/01/08 13:45:06
0 2016/01/15 22:37:08
There are six clips that hold this front panel in. Begin by pulling up around the ones closest to the oil filter. Then chose either side and pull up. I typically go for the one closest to the intake manifold first.
There are six clips that hold this front panel in. Begin by pulling up around the ones closest to the oil filter. Then chose either side and pull up. I typically go for the one closest to the intake manifold first.
0 2016/01/19 21:07:02
Note the mounting points of all ten torx screws. Don't forget the ones in the back.
Note the mounting points of all ten torx screws. Don't forget the ones in the back.
0 2016/01/19 21:07:03