Engine Check Error Code: P0303 & P0313
#1
Newbie
Thread Starter
Join Date: Jan 2006
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
2004 c230 sedan
Engine Check Error Code: P0303 & P0313
Hi,
Can someone who has access to a service manual tell me what the following error codes exactly mean and how I go about remedying the situation:
P0304: Cylinder 4 Misfire
P0313: Low Fuel Level Detection
Thanks!!!
Can someone who has access to a service manual tell me what the following error codes exactly mean and how I go about remedying the situation:
P0304: Cylinder 4 Misfire
P0313: Low Fuel Level Detection
Thanks!!!
#4
MBWorld Fanatic!
Join Date: Mar 2009
Location: GA
Posts: 2,135
Likes: 0
Received 6 Likes
on
6 Posts
2016 Chevrolet SS, 2006 Cadillac STS-V
I'm thinking I've read something about coils being a problem. Try swapping the plug with one cylinder and the coil with another cylinder and see if the misfire follows. I'd start with the misfire first, because that could fix the other code.
Last edited by 91RS; 07-29-2009 at 09:07 PM.
#5
Super Moderator
P0313 = Misfire Detected with Low Fuel
Fill the fuel tank - check fuel filter - do as 91RS states - wires, plugs, coils.
This is really a fuel starvation problem. Fuel pump might be getting lazy but check filter first.
Fill the fuel tank - check fuel filter - do as 91RS states - wires, plugs, coils.
This is really a fuel starvation problem. Fuel pump might be getting lazy but check filter first.
Last edited by Glyn M Ruck; 07-30-2009 at 08:16 AM.
#7
Newbie
Hi I have 2005 c230k with 46000 miles on it , on friday my engine start runing rough , at first there wasn't any cel on , then after i drive for a while the car went fine , on saturday i went to start the car in the afternoom , it runs very rough again from cold start and rough idle didn't go away even after I drove it for a while .. cel came on after 30 miles then I got the code for p0300 p0301 p0302 p0303 p0304 and p0313 is the pending code for fuel low . now I have been reading alot post here about the rough idle problem here . my car only runs rough on idle . once I start going the engine feels fine and no power lost but only idle really rough like it about to choke but it just dosn't die on me ( I guess it's a good thing ) last time I took the car into dealer to get two valve changed for supercharge system , that was 3 month ago I check with the SA all the recall has been done on my car ( but I will check again just to see if SA miss anything ) so I guess that would be the fuel system that's causing the problem . and the code I got was from a scan tool ( should I have my friends put on the start system to see if there is anymore code ?) please help , your time will be thankful
Trending Topics
#9
Senior Member
This happened to my C240, has 98k miles, and 5 cylinders misfired.. It drove normal two days later, and my friend cleared my codes. Is there anyway to prevent this in the future? (I guess I'm saying I have the same problem too)
#10
Hi I have 2005 c230k with 46000 miles on it , on friday my engine start runing rough , at first there wasn't any cel on , then after i drive for a while the car went fine , on saturday i went to start the car in the afternoom , it runs very rough again from cold start and rough idle didn't go away even after I drove it for a while .. cel came on after 30 miles then I got the code for p0300 p0301 p0302 p0303 p0304 and p0313 is the pending code for fuel low . now I have been reading alot post here about the rough idle problem here . my car only runs rough on idle . once I start going the engine feels fine and no power lost but only idle really rough like it about to choke but it just dosn't die on me ( I guess it's a good thing ) last time I took the car into dealer to get two valve changed for supercharge system , that was 3 month ago I check with the SA all the recall has been done on my car ( but I will check again just to see if SA miss anything ) so I guess that would be the fuel system that's causing the problem . and the code I got was from a scan tool ( should I have my friends put on the start system to see if there is anymore code ?) please help , your time will be thankful