Before - After Comparison - C63 dropped on H&R Springs
#26
So 0.15 degrees of toe in the rear on a C63 is what you guys are doing Advanced?
I lowered mine and had the toe reduced to 0.20 I believe.
I think the lowest spec is 0.25. Which is still a fair amount compared to other cars.
I lowered mine and had the toe reduced to 0.20 I believe.
I think the lowest spec is 0.25. Which is still a fair amount compared to other cars.
#28
Member
Join Date: Oct 2011
Posts: 169
Likes: 0
Received 0 Likes
on
0 Posts
bmw e-60 550i,bmw e-92 m3, c63coupe p31, stable of Italian stallions MV's
I just lowered my c 63 coupe with H&R springs with 17 mm pads instead. It looks perfect. The rear and the front are even. I had a alignment at the mercedes dealership, they also installled the springs for me. I know the owner, so It reasonable for the job. I did have to buy bolts for the front end to get the toe or camber correct to factory spec's. The rear were good.
#29
MBWorld Fanatic!
so from what I understand, there is really no performance gain from this set up and the negative camber cannot be readjusted, resulting in more tire eating? also, with this set up, will it shorten the life of the shocks?
I am interested in the lowering, but if its going to make the car handle worse at the limit, chew through tires more on the street and shorten the life of my shocks I wont do it. It does look good though.
I am interested in the lowering, but if its going to make the car handle worse at the limit, chew through tires more on the street and shorten the life of my shocks I wont do it. It does look good though.
#30
MBWorld Fanatic!
there are adjustable camber bolts you can buy to replace non-adjustable bolts currently i think...i had them put in. THey are off the upper end models CLS/E/SL i believe, factory part
#33
MBWorld Fanatic!
OEM Camber Bolts
000-333-09-71 / 000-333-10-71
I think its the one with the 000-333-10-71 in it. 59.99$ per set. These are for front wheels, you need 2 sets. Not sure how much camber adjustment you get, but I had them put in.
000-333-09-71 / 000-333-10-71
I think its the one with the 000-333-10-71 in it. 59.99$ per set. These are for front wheels, you need 2 sets. Not sure how much camber adjustment you get, but I had them put in.
#34
Member
Join Date: Jun 2011
Location: Someplace Warm
Posts: 202
Likes: 0
Received 0 Likes
on
0 Posts
2009 C63
I don't understand why you guys all get the taller rear spring pads?? I installed my H&R springs last weekend (took about 3 hours to do myself) and I still wish the rear would go a little LOWER, not higher. ![Frown](https://mbworld.org/forums/images/smilies/frown.gif)
By the way, the ride is great. A little firmer then stock, but more comfortable...if that makes sense. It feels firmer on big dips on the road or big bumps, but over very small imperfections I actually feel like the H&R's make it a little less jarring then the factory springs.
![Frown](https://mbworld.org/forums/images/smilies/frown.gif)
By the way, the ride is great. A little firmer then stock, but more comfortable...if that makes sense. It feels firmer on big dips on the road or big bumps, but over very small imperfections I actually feel like the H&R's make it a little less jarring then the factory springs.
#35
Former Vendor of MBWorld
Thread Starter
I would have to double check with the actual tech but we would try to go as close as possible to factory spec.
#36
Former Vendor of MBWorld
Thread Starter
so from what I understand, there is really no performance gain from this set up and the negative camber cannot be readjusted, resulting in more tire eating? also, with this set up, will it shorten the life of the shocks?
I am interested in the lowering, but if its going to make the car handle worse at the limit, chew through tires more on the street and shorten the life of my shocks I wont do it. It does look good though.
I am interested in the lowering, but if its going to make the car handle worse at the limit, chew through tires more on the street and shorten the life of my shocks I wont do it. It does look good though.
#37
Member
I'm clueless when it comes to alignment, but was hoping someone could confirm the following? From what I can see on these forums, I've gathered that:
1. It's not possible to reduce the negative rear camber that comes with lowering the C63 using H&R springs.
2. It's also not possible to adjust the rear camber even if you use coilovers (that is, without adjusting ride height).
3. The camber bolts people speak of on here will only allow adjusting the camber in the fronts and not the rears.
Is this correct? Thanks for your help
1. It's not possible to reduce the negative rear camber that comes with lowering the C63 using H&R springs.
2. It's also not possible to adjust the rear camber even if you use coilovers (that is, without adjusting ride height).
3. The camber bolts people speak of on here will only allow adjusting the camber in the fronts and not the rears.
Is this correct? Thanks for your help
#38
MBWorld Fanatic!
I'm clueless when it comes to alignment, but was hoping someone could confirm the following? From what I can see on these forums, I've gathered that:
1. It's not possible to reduce the negative rear camber that comes with lowering the C63 using H&R springs.
2. It's also not possible to adjust the rear camber even if you use coilovers (that is, without adjusting ride height).
3. The camber bolts people speak of on here will only allow adjusting the camber in the fronts and not the rears.
Is this correct? Thanks for your help
1. It's not possible to reduce the negative rear camber that comes with lowering the C63 using H&R springs.
2. It's also not possible to adjust the rear camber even if you use coilovers (that is, without adjusting ride height).
3. The camber bolts people speak of on here will only allow adjusting the camber in the fronts and not the rears.
Is this correct? Thanks for your help
#39
Member
Hey Duane thanks for giving me the run down on this. After I posted, I did find some threads talking about some aftermarket solutions such as Kmac(?) bushings and the upper arms you mentioned for adjusting camber. Just not sure if I want to go to such lengths.
I put about 2,000 miles on my car a year and might give it a whirl at a track maybe 1-2 times a year - nothing too hardcore. I'm thinking maybe the tire wear won't affect me all too much(?), and maybe the negative camber that I'm stuck with will be adequate for my purposes. I thought a lot about going the coilover route too. I had kw v3s on my m3 back in the day and loved them. But also know all the headaches that come with those. Didn't want to go through all that tinkering this time around, and don't even have the time to these days anyway.
Thanks again for clarifying this for me though - much appreciated
I put about 2,000 miles on my car a year and might give it a whirl at a track maybe 1-2 times a year - nothing too hardcore. I'm thinking maybe the tire wear won't affect me all too much(?), and maybe the negative camber that I'm stuck with will be adequate for my purposes. I thought a lot about going the coilover route too. I had kw v3s on my m3 back in the day and loved them. But also know all the headaches that come with those. Didn't want to go through all that tinkering this time around, and don't even have the time to these days anyway.
Thanks again for clarifying this for me though - much appreciated