JB4 is here!
#101
Former Vendor of MBWorld
Joined: Dec 2005
Posts: 827
Likes: 152
From: Simi Valley, California
2018 C63 Sedan
Got the WMI kit, looking at the install manual it appears this mod will delete the air cabin filters. I am not sure I am OK with leaving that sitting wide open under the hood. Anyone else install one yet? What did you do?
https://www.n54tech.com/instructions...mi_install.pdf
https://www.n54tech.com/instructions...mi_install.pdf
#105
Former Vendor of MBWorld
Joined: Dec 2005
Posts: 827
Likes: 152
From: Simi Valley, California
2018 C63 Sedan
Got the WMI kit, looking at the install manual it appears this mod will delete the air cabin filters. I am not sure I am OK with leaving that sitting wide open under the hood. Anyone else install one yet? What did you do?
https://www.n54tech.com/instructions...mi_install.pdf
https://www.n54tech.com/instructions...mi_install.pdf
-Payam
#107
I just got my WMI kit installed and I mounted it low enough that I could keep the cabin air filter.
I just need the WMI Firmware update and then ready to test, the tank is loaded with 50/50 mix and then I am ready to dyno.
Here are some pics of my install of the WMI
#108
I had my JB4 installed last week at close friend's indy shop. After messing with it for an hour and a half dropping a bolt on the under tray and ripping out Map sensor 1 lock tab, I gave up. This is nothing like the install on my 335i. I could not even get the rubber shroud loose enough to adequately remove map sensor one. It took my guy 3 hrs with help from another tech to install it. Granted, this was his first time. I'd say 1 and half hours the next time. Anyways, I instantly noticed the added power pulling out of the shop. The JB4 defaults to map 1 when plugged into the ODBII port. I did not know that so I was pleasantly surprised. I played in Map 1 for a couple days then switched to map 2. Holy Crap! This thing woke the hec up! To be honest, traction is now a major concern. You'll be lighting up your rear tires in first and second and this is in sport + manual mode. Until I can mess with the boost by gear settings on the JB4 and get this thing to hook, more power is the least of my worries right now. I need to schedule a Dyno session sometime next week. I just need to find a good shop. I figured I do a run with JB4 off (Stock), one in map one ( 4 psi over stock) and another in Map 2 (5 psi over stock). Not sure if I want to try maps 3,4,5 yet. At least not before I install ethanol sensor from Fuel-it and at least know what mixture.
Last edited by AMGMessiah; 06-27-2019 at 09:04 AM.
#109
Senior Member
Joined: Oct 2013
Posts: 418
Likes: 90
From: Edmonton AB
2015 C63S ,DME Tune, KW Has ,Kmac Bushings,BC Forged wheels,Gt Rotors,Porterfield R4S,Modal Intake
Usually when there are a lack of response or no data at all its because the gains haven't been what they hoped for and if they were to post them then no one would buy them . On the Bwm's they posted tons of results over time and hyped it up and sold lots ...
The following users liked this post:
Go Dawgs (03-18-2021)
#110
Between AMGMessiah and Vader, we should hopefully have some good dyno results soon.
Vader, I am selfishly hoping that you don’t muddle the dyno process with the methanol, or at least make sure you get clean JB4 vs base maps before turning that on, or else it will certainly skew the real world results for everyone just running JB4
#111
I had my JB4 installed last week at close friend's indy shop. After messing with it for an hour and a half dropping a bolt on the under tray and ripping out Map sensor 1 lock tab, I gave up. This is nothing like the install on my 335i. I could not even get the rubber shroud loose enough to adequately remove map sensor one. It took my guy 3 hrs with help from another tech to install it. Granted, this was his first time. I'd say 1 and half hours the next time. Anyways, I instantly noticed the added power pulling out of the shop. The JB4 defaults to map 1 when plugged into the ODBII port. I did not know that so I was pleasantly surprised. I played in Map 1 for a couple days then switched to map 2. Holy Crap! This thing woke the hec up! To be honest, traction is now a major concern. You'll be lighting up rear your tires in first and second and this is in sport + manual mode. Until I can mess with the boost by gear settings on the JB4 and get this thing to hook, more power is the least of my worries right now. I need to schedule a Dyno session sometime next week. I just need to find a good shop. I figured I do a run with JB4 off (Stock), one in map one ( 4 psi over stock) and another in Map 2 (5 psi over stock). Not sure if I want to try maps 3,4,5 yet. At least not before I install ethanol sensor from Fuel-it and at least know what mixture.
oh well, all the more reason why a nicely done install video from BMS would be very helpful. Last I heard, they were working on that a few months ago!
#112
The two map sensors 1 and 3 are the most difficult. A video showing that plastic shroud fully exposing Map sensor 1,3 and what to remove to get there would be very helpful. Otherwise the online install guide is quite good. I guess if I had removed additional sensors and fasteners, I would have freed up more clearance. I just did not know which ones and I did not want to risk damaging anything and pulling too hard or forcing it. I freaked out when I dropped the bolt and ripped out the lock tab on map sensor 1 and when my lower back started aching, it was time to hang it up..lol.
#113
Former Vendor of MBWorld
Joined: Dec 2005
Posts: 827
Likes: 152
From: Simi Valley, California
2018 C63 Sedan
It's easy to turn the tuning on and off and feel the difference or measure it via a dragy or track if you're so inclined too.
#114
I can relate. My former 335i made 535 rwhp and 560 rwtq modded to the gills with JB4, E60, PI, Pure Stage 2 turbo and FBO. I did not not find out till over a year later that it made that much power. I just knew it was fast..lol. With my C63s, I feel the power is there and quite similar to my former car. I am doing the dyno mainly for service to board members more than anything..and a bit of curiosity on my end. I bet if folks here chipped in for a board member to go dyno their car, you would see a ton of dyno graphs..lol.
Last edited by AMGMessiah; 06-27-2019 at 02:59 PM.
#115
Former Vendor of MBWorld
Joined: Dec 2005
Posts: 827
Likes: 152
From: Simi Valley, California
2018 C63 Sedan
Peak numbers will be the same as we have dyno sheets on our website. Delta will be a bit lower because the C63s makes a bit more power than a standard C63.
Gains are noticeable and our 1/4 mile runs are showing a 10mph gain trap speed, so that should speak volumes.
-Payam
Gains are noticeable and our 1/4 mile runs are showing a 10mph gain trap speed, so that should speak volumes.
-Payam
#116
Other than that, are there any other goodies you can mention that you guys are working on or are testing, that can be integrated into future firmware? I suppose WMI counts as one, but things like exhaust valve control and other toys that the OBD2 and CANBUS connections let you play with?
#117
Former Vendor of MBWorld
Joined: Dec 2005
Posts: 827
Likes: 152
From: Simi Valley, California
2018 C63 Sedan
Payam, have you guys moved toward officially recognizing Map 2 as being a safe choice for 93 octane C63S cars? I remember in the original thread, BMS mentioned that S models were only tested with Map 1 so that was basically it as far as the recommended map to run, but that was months ago. This could also all roll into the broader topic of the product officially coming off BETA, I suppose.
Other than that, are there any other goodies you can mention that you guys are working on or are testing, that can be integrated into future firmware? I suppose WMI counts as one, but things like exhaust valve control and other toys that the OBD2 and CANBUS connections let you play with?
Other than that, are there any other goodies you can mention that you guys are working on or are testing, that can be integrated into future firmware? I suppose WMI counts as one, but things like exhaust valve control and other toys that the OBD2 and CANBUS connections let you play with?
From what we have seen map 2 is fine on 93 as well.
We're working on a few things actually. Terry would be able to tell you exactly what. I don't want to say anything I shouldn't especially prematurely. Don't want you guys to expect something, and we see that we're not able to do it in the end.
I'll tell you that the development will never stop and we're always looking for more innovative things to keep the platform moving forward.
-Payam
The following users liked this post:
ezatnova (06-27-2019)
#118
Is anyone looking for a Water Meth Kit. I am going in a different direction and have the kit minus the tank. Brand new in box and im willing to discount it for someone in need! PM me!!!
#119
Scheduled for Dyno July 10th, too bad it’s so hot here but gotta do it! Here are my thoughts on the pulls, could use some input. What is the 1 to 1 gear ratio in these cars 3rd or 4th gear? What have others been using?
My suggested dyno pulls:
1. JB4 off, Full stock with paper filters in comfort mode
2. Stock with Race mode
3. Stock with High Flow air filters in Race Mode
4. JB M1 with Boost Reduction by gear off for all JB4 pulls
5. JB4 M2 - I’ll this be worth it on 91 oct fuel ?
6. JB4 M8 “valet mode”
7. JB4 M7 WMI with settings at 5psi over stock, 60 sig scale and 9psi min boost
8. Could or should I bump it to 6 psi over stock for MAP 7? Or lower the min psi to 7 or 8?
My suggested dyno pulls:
1. JB4 off, Full stock with paper filters in comfort mode
2. Stock with Race mode
3. Stock with High Flow air filters in Race Mode
4. JB M1 with Boost Reduction by gear off for all JB4 pulls
5. JB4 M2 - I’ll this be worth it on 91 oct fuel ?
6. JB4 M8 “valet mode”
7. JB4 M7 WMI with settings at 5psi over stock, 60 sig scale and 9psi min boost
8. Could or should I bump it to 6 psi over stock for MAP 7? Or lower the min psi to 7 or 8?
#120
Scheduled for Dyno July 10th, too bad it’s so hot here but gotta do it! Here are my thoughts on the pulls, could use some input. What is the 1 to 1 gear ratio in these cars 3rd or 4th gear? What have others been using?
My suggested dyno pulls:
1. JB4 off, Full stock with paper filters in comfort mode
2. Stock with Race mode
3. Stock with High Flow air filters in Race Mode
4. JB M1 with Boost Reduction by gear off for all JB4 pulls
5. JB4 M2 - I’ll this be worth it on 91 oct fuel ?
6. JB4 M8 “valet mode”
7. JB4 M7 WMI with settings at 5psi over stock, 60 sig scale and 9psi min boost
8. Could or should I bump it to 6 psi over stock for MAP 7? Or lower the min psi to 7 or 8?
My suggested dyno pulls:
1. JB4 off, Full stock with paper filters in comfort mode
2. Stock with Race mode
3. Stock with High Flow air filters in Race Mode
4. JB M1 with Boost Reduction by gear off for all JB4 pulls
5. JB4 M2 - I’ll this be worth it on 91 oct fuel ?
6. JB4 M8 “valet mode”
7. JB4 M7 WMI with settings at 5psi over stock, 60 sig scale and 9psi min boost
8. Could or should I bump it to 6 psi over stock for MAP 7? Or lower the min psi to 7 or 8?
Couple general suggestions.
Make sure you get comfortable with how to put the car into dyno mode. Sounds simple but God forbid the shop doesn’t know how to do it, the car won’t be able to complete the tests if the traction/safety/ABS systems are going bonkers.
You must be in the Odometer home dashboard screen, not the AMG screen or any of the others before doing it.
Practice this a few times while at home so it isn’t something you’re figuring out while the shop’s clock is running! https://mbworld.org/forums/c63-c63s-...tructions.html
You want 5th gear. That is 1:1 in our 7 speed.
You want the car is Manual trans setting otherwise it will kick down after you’re in 5th gear.
Let the shop know how many runs you plan on doing so they can schedule time accordingly. You’ll need a decent chunk of time for 8 runs with some changes in between.
The list looks great. #1-3 will be so nice to see, for everyone in the community.
Hopefully it’s worth doing #5 on 91 (map 2). Maybe BMS can confirm that you might just see limited additional power, and not that it’s dangerous to do?
Take lots of videos and pictures!
I may see about installing mine this weekend. I really wanted to wait and do the BMS intake at the same time but they are really delayed with no firm end in sight.
#121
This is great!
Couple general suggestions.
Make sure you get comfortable with how to put the car into dyno mode. Sounds simple but God forbid the shop doesn’t know how to do it, the car won’t be able to complete the tests if the traction/safety/ABS systems are going bonkers.
You must be in the Odometer home dashboard screen, not the AMG screen or any of the others before doing it.
Practice this a few times while at home so it isn’t something you’re figuring out while the shop’s clock is running! https://mbworld.org/forums/c63-c63s-...tructions.html
You want 5th gear. That is 1:1 in our 7 speed.
You want the car is Manual trans setting otherwise it will kick down after you’re in 5th gear.
Let the shop know how many runs you plan on doing so they can schedule time accordingly. You’ll need a decent chunk of time for 8 runs with some changes in between.
The list looks great. #1-3 will be so nice to see, for everyone in the community.
Hopefully it’s worth doing #5 on 91 (map 2). Maybe BMS can confirm that you might just see limited additional power, and not that it’s dangerous to do?
Take lots of videos and pictures!
I may see about installing mine this weekend. I really wanted to wait and do the BMS intake at the same time but they are really delayed with no firm end in sight.
Couple general suggestions.
Make sure you get comfortable with how to put the car into dyno mode. Sounds simple but God forbid the shop doesn’t know how to do it, the car won’t be able to complete the tests if the traction/safety/ABS systems are going bonkers.
You must be in the Odometer home dashboard screen, not the AMG screen or any of the others before doing it.
Practice this a few times while at home so it isn’t something you’re figuring out while the shop’s clock is running! https://mbworld.org/forums/c63-c63s-...tructions.html
You want 5th gear. That is 1:1 in our 7 speed.
You want the car is Manual trans setting otherwise it will kick down after you’re in 5th gear.
Let the shop know how many runs you plan on doing so they can schedule time accordingly. You’ll need a decent chunk of time for 8 runs with some changes in between.
The list looks great. #1-3 will be so nice to see, for everyone in the community.
Hopefully it’s worth doing #5 on 91 (map 2). Maybe BMS can confirm that you might just see limited additional power, and not that it’s dangerous to do?
Take lots of videos and pictures!
I may see about installing mine this weekend. I really wanted to wait and do the BMS intake at the same time but they are really delayed with no firm end in sight.
#122
Thanks for help and advice, that is really awesome! Realized that I don’t need to worry about boost reduction by gear as I won’t be using 1,2nd gears for dyno pulls. I’ll do some practice today/tonight, i had some CEL’s this AM start up, but turned off the car, cleared them and they did not return. Seems like a very slight miss on one cyl perhaps, maybe I fouled a plug or something.
#123
Former Vendor of MBWorld
Joined: Dec 2005
Posts: 827
Likes: 152
From: Simi Valley, California
2018 C63 Sedan
Scheduled for Dyno July 10th, too bad it’s so hot here but gotta do it! Here are my thoughts on the pulls, could use some input. What is the 1 to 1 gear ratio in these cars 3rd or 4th gear? What have others been using?
My suggested dyno pulls:
1. JB4 off, Full stock with paper filters in comfort mode
2. Stock with Race mode
3. Stock with High Flow air filters in Race Mode
4. JB M1 with Boost Reduction by gear off for all JB4 pulls
5. JB4 M2 - I’ll this be worth it on 91 oct fuel ?
6. JB4 M8 “valet mode”
7. JB4 M7 WMI with settings at 5psi over stock, 60 sig scale and 9psi min boost
8. Could or should I bump it to 6 psi over stock for MAP 7? Or lower the min psi to 7 or 8?
My suggested dyno pulls:
1. JB4 off, Full stock with paper filters in comfort mode
2. Stock with Race mode
3. Stock with High Flow air filters in Race Mode
4. JB M1 with Boost Reduction by gear off for all JB4 pulls
5. JB4 M2 - I’ll this be worth it on 91 oct fuel ?
6. JB4 M8 “valet mode”
7. JB4 M7 WMI with settings at 5psi over stock, 60 sig scale and 9psi min boost
8. Could or should I bump it to 6 psi over stock for MAP 7? Or lower the min psi to 7 or 8?
#124
The codes were:
0300
0800
4833
E617
5CA3
0000
We shall see if it starts that way today.
I do have the BCM module installed, but not really sure how I utilize it.
#125
Former Vendor of MBWorld
Joined: Dec 2005
Posts: 827
Likes: 152
From: Simi Valley, California
2018 C63 Sedan
My car sits for days at a time, so might have just been some Water/Meth vapors sitting in there and created a weird start up that messed with the computer.
The codes were:
0300
0800
4833
E617
5CA3
0000
We shall see if it starts that way today.
I do have the BCM module installed, but not really sure how I utilize it.
The codes were:
0300
0800
4833
E617
5CA3
0000
We shall see if it starts that way today.
I do have the BCM module installed, but not really sure how I utilize it.