Brembo Rotors
#1
Senior Member
Thread Starter
Join Date: Feb 2003
Location: So. Cali
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
2002 CLK 430/2002 325i
Brembo Rotors
Set of rear Brembo cross drilled rotors that were on a CLK. I believe these should also fit W210 and W202. I no longer have a need for them since I upgraded to a BBK for the rear. These rotors have approximately 8500 miles. These were purchased from a Brembo distributor.
I am asking only $125. Prefer a So Cal buyer, but willing to ship at buyer's expense.
I am asking only $125. Prefer a So Cal buyer, but willing to ship at buyer's expense.
#6
Senior Member
Join Date: Aug 2005
Location: Phoenix, Az
Posts: 329
Likes: 0
Received 0 Likes
on
0 Posts
02 C32R
can you post the dimensions, like width and thickness of the rotor. I am curious to see how close they are the the C32 rear brakes.
Last edited by Dead Ringer; 10-07-2005 at 01:24 PM.
#7
Senior Member
Thread Starter
Join Date: Feb 2003
Location: So. Cali
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
2002 CLK 430/2002 325i
mig888- sounds good.
Chi500- They will work with your stock calipers. No need for additional parts, unless you have a need to change out your brake pads.
pshek- I don't think that it will work on a W203. W203 & W209 share similar chassis. Same thing for W202 & W208...similar chassis.
Dead Ringer- I will post some pics tonite and take some dimensional measurements.
Chi500- They will work with your stock calipers. No need for additional parts, unless you have a need to change out your brake pads.
pshek- I don't think that it will work on a W203. W203 & W209 share similar chassis. Same thing for W202 & W208...similar chassis.
Dead Ringer- I will post some pics tonite and take some dimensional measurements.
Trending Topics
#12
Senior Member
Thread Starter
Join Date: Feb 2003
Location: So. Cali
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
2002 CLK 430/2002 325i
Did not have my micrometer at home to measure the thickness of the rotors (I will post the thickness later), but I did take some pics as requested....
![](http://www.benzworld.org/gallery/pics/15575052010102005115427PM.JPG)
Last edited by Benzoxtc; 10-11-2005 at 12:14 AM.
#14
Senior Member
Thread Starter
Join Date: Feb 2003
Location: So. Cali
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
2002 CLK 430/2002 325i
[QUOTE=Dead Ringer]looks like the holes are sweeping the wrong way, dang...[/QUOTE
Pics are showing front and back side of same rotor, holes are sweeping in the right direction.
Pics are showing front and back side of same rotor, holes are sweeping in the right direction.
#17
Senior Member
Join Date: Aug 2005
Location: Phoenix, Az
Posts: 329
Likes: 0
Received 0 Likes
on
0 Posts
02 C32R
looks like the bottom pic has the hat facing outward ( ie the way it would be mounted) and has the hole sweeping forwards, meaning that if it was mounted on the drivers side they would be "throwing" forward, mine are throwing backwards. Maybe the lower pic is showing the backside and I need to get my eyes checked..
#18
Senior Member
Thread Starter
Join Date: Feb 2003
Location: So. Cali
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
2002 CLK 430/2002 325i
Not sure what to tell you at this moment, with regards to direction of holes....I will take a pic of both rotors side by side for comparison.
c43amg-I believe the sixth hole is to secure the rotor, other five holes are for the lug bolts to secure the wheel.
c43amg-I believe the sixth hole is to secure the rotor, other five holes are for the lug bolts to secure the wheel.