Service Brake "Visit Workshop!"
#27
Super Member
Join Date: Apr 2005
Location: Boston, MA USA
Posts: 666
Likes: 0
Received 3 Likes
on
3 Posts
03 E320 -wife's car now; 07 Porsche Boxster S - my toy
Tariq,
I'm at a loss for ideas. I would probably change the stop lamp switch as was suggested earlier and watch the car for a couple of weeks. If the warning still appeared, I would check all three pad sensor's connectors to make sure they're not loose. If you can find it, WIS document AH42.10-P-0003-01A has info pertaining to the pad sensors.
Regards,
paul....
I'm at a loss for ideas. I would probably change the stop lamp switch as was suggested earlier and watch the car for a couple of weeks. If the warning still appeared, I would check all three pad sensor's connectors to make sure they're not loose. If you can find it, WIS document AH42.10-P-0003-01A has info pertaining to the pad sensors.
Regards,
paul....
#28
Member
Join Date: Dec 2003
Location: CHESTERFIELD U.K.
Posts: 78
Likes: 0
Received 1 Like
on
1 Post
E320 CDI W211
Yes I took my car to the dealers four times about the problem (BRAKES VISIT WORKSHOP).
The malfunction would not retain the information on the problem....this would reset after 15 minutes when the car was switched off.
The dealer fited new censors,wiring loom and removed the ((50% brake wear censor which by the way should be done on recalls because this can cause interference on the radio when the rotor cuts the 50% censor)).
FINALY on the fourth visit I drove to the workshop with warning BRAKES VISIT WORKSHOP still visuable on the malfunction display.....the technician pluged the workshop computer (STAR DIAGNOSE) printed out the report and showed me that it was a faulty brake light switch.
Took just over 30 minutes and I was driving the car back home.
Problem solved......no more malfunction 3 months later plus 2000 miles.
The malfunction would not retain the information on the problem....this would reset after 15 minutes when the car was switched off.
The dealer fited new censors,wiring loom and removed the ((50% brake wear censor which by the way should be done on recalls because this can cause interference on the radio when the rotor cuts the 50% censor)).
FINALY on the fourth visit I drove to the workshop with warning BRAKES VISIT WORKSHOP still visuable on the malfunction display.....the technician pluged the workshop computer (STAR DIAGNOSE) printed out the report and showed me that it was a faulty brake light switch.
Took just over 30 minutes and I was driving the car back home.
Problem solved......no more malfunction 3 months later plus 2000 miles.
#29
Super Member
Join Date: Apr 2005
Location: Boston, MA USA
Posts: 666
Likes: 0
Received 3 Likes
on
3 Posts
03 E320 -wife's car now; 07 Porsche Boxster S - my toy
Originally Posted by LeslieRushforth
Yes I took my car to the dealers four times about the problem (BRAKES VISIT WORKSHOP).
The malfunction would not retain the information on the problem....this would reset after 15 minutes when the car was switched off.
The dealer fited new censors,wiring loom and removed the ((50% brake wear censor which by the way should be done on recalls because this can cause interference on the radio when the rotor cuts the 50% censor)).
FINALY on the fourth visit I drove to the workshop with warning BRAKES VISIT WORKSHOP still visuable on the malfunction display.....the technician pluged the workshop computer (STAR DIAGNOSE) printed out the report and showed me that it was a faulty brake light switch.
Took just over 30 minutes and I was driving the car back home.
Problem solved......no more malfunction 3 months later plus 2000 miles.
The malfunction would not retain the information on the problem....this would reset after 15 minutes when the car was switched off.
The dealer fited new censors,wiring loom and removed the ((50% brake wear censor which by the way should be done on recalls because this can cause interference on the radio when the rotor cuts the 50% censor)).
FINALY on the fourth visit I drove to the workshop with warning BRAKES VISIT WORKSHOP still visuable on the malfunction display.....the technician pluged the workshop computer (STAR DIAGNOSE) printed out the report and showed me that it was a faulty brake light switch.
Took just over 30 minutes and I was driving the car back home.
Problem solved......no more malfunction 3 months later plus 2000 miles.
Leslie,
It's good hearing from you again. By the way, I replaced my rear pads/rotors last week with confidence because of the info you furnished me some time ago with dealing with the SBC -- thanks!
regards,
Paul....
#30
Super Member
Thread Starter
I did the DAS setup for the 2nd time.. it removed, but it comes back agine..
i will try the brake light switch sensor...
Any one have idea about the part number and how it looks in photo?
Is it hard to do self installation?
Regards....
i will try the brake light switch sensor...
Any one have idea about the part number and how it looks in photo?
Is it hard to do self installation?
Regards....
#31
Super Member
Thread Starter
I opened the cover which is under the dashbord where the padels... i notice the following as u can see the the photos... i guess this is the sensor or switch which i must replace.. i hope someone can explein more..
btw i notice a cable which is unpluged too, i try to find where it must plugged but didnt find...
any one can advise?
Regards
btw i notice a cable which is unpluged too, i try to find where it must plugged but didnt find...
any one can advise?
Regards
#32
there is a tab you need to squeeze on the sensor you have pictured and then you turn it approximately 90 degrees and it'll come out. dont forget when you install the sensor you need to make sure the tan/white tab that gets compressed is fully extended (you can press it dont and hear the notches when its going down, but make sure its fully extended). The stop lamp switch should fix that cluster message 99 percent of the time.
#33
Super Member
Thread Starter
Originally Posted by D_TECH
there is a tab you need to squeeze on the sensor you have pictured and then you turn it approximately 90 degrees and it'll come out. dont forget when you install the sensor you need to make sure the tan/white tab that gets compressed is fully extended (you can press it dont and hear the notches when its going down, but make sure its fully extended). The stop lamp switch should fix that cluster message 99 percent of the time.
Thanks D_TECH...
I feel well after i red your comments...
btw do you have the part number for that switch?
and about removing it, do you mean i must turn it to the right will 90 Degree then pull it out ...?
Hope to get more explien rather than i may broke it ....
![smash](https://mbworld.org/forums/images/smilies/smashfreak.gif)
#35
Super Member
Thread Starter
Originally Posted by D_TECH
i dont think I have any switches at work to get the part number, sorry, and yes you squeeze the tab and turn to the right.
![Frown](https://mbworld.org/forums/images/smilies/frown.gif)
![wall](https://mbworld.org/forums/images/smilies/banghead.gif)
#37
MBWorld Fanatic!
Join Date: Jan 2004
Location: Salt Lake City (but not Morm)
Posts: 7,092
Likes: 0
Received 12 Likes
on
10 Posts
2003 E55 & 2014 GL550
This gonna sound a little dumb but you sound like you are kinda at the end of your rope. Very similiar thing happened to me with the light. I called the service guy and he shot this out instantly, "You bumped the emergency brake with your foot. Sometims when getting in the car, your left foot brushes that emergency brake and she sets off the sensors." Told me to make sure emergency brake was ALL the way up and drive for a few mins. WHAMMO....light GONE. Sure hope this works....you have been through a lot. Good Luck.
The following users liked this post:
Pepe1969 (12-09-2020)
#38
Super Member
Thread Starter
Originally Posted by Jakpro1
This gonna sound a little dumb but you sound like you are kinda at the end of your rope. Very similiar thing happened to me with the light. I called the service guy and he shot this out instantly, "You bumped the emergency brake with your foot. Sometims when getting in the car, your left foot brushes that emergency brake and she sets off the sensors." Told me to make sure emergency brake was ALL the way up and drive for a few mins. WHAMMO....light GONE. Sure hope this works....you have been through a lot. Good Luck.
#39
Almost a Member!
Join Date: Sep 2003
Location: UAE
Posts: 44
Likes: 0
Received 0 Likes
on
0 Posts
E240 03
Hi Tarek
Try to remove the wires that connect the brake pads to the disc. they are small wires that u bought for 10 AED.
When I changed my brake pads and turned on the car, I received that message with beeping sound, then I removed those wires and it is all gone.
Take the car to Dubai even if it is imported they will fix it for you because this is a recall and they had to change it. I tool mine to Sharjah they refused to fix it, then I wrote a complaint message and sent it to the GM of Dubai CCing their Customer Relations. It was unbeleivable the service manager called me (he is German) and appologised and told me to get him the car.
They fixed many things for free and did all the recalls, the whole job was worth around 15,000 AED (more than 4000 US Dollars). they changed the brake bump for 10000 (around 2500 UD dollars).
When I changed my brake pads and turned on the car, I received that message with beeping sound, then I removed those wires and it is all gone.
Take the car to Dubai even if it is imported they will fix it for you because this is a recall and they had to change it. I tool mine to Sharjah they refused to fix it, then I wrote a complaint message and sent it to the GM of Dubai CCing their Customer Relations. It was unbeleivable the service manager called me (he is German) and appologised and told me to get him the car.
They fixed many things for free and did all the recalls, the whole job was worth around 15,000 AED (more than 4000 US Dollars). they changed the brake bump for 10000 (around 2500 UD dollars).
#40
Super Member
Thread Starter
Originally Posted by byttcool99
Try to remove the wires that connect the brake pads to the disc. they are small wires that u bought for 10 AED.
When I changed my brake pads and turned on the car, I received that message with beeping sound, then I removed those wires and it is all gone.
Take the car to Dubai even if it is imported they will fix it for you because this is a recall and they had to change it. I tool mine to Sharjah they refused to fix it, then I wrote a complaint message and sent it to the GM of Dubai CCing their Customer Relations. It was unbeleivable the service manager called me (he is German) and appologised and told me to get him the car.
They fixed many things for free and did all the recalls, the whole job was worth around 15,000 AED (more than 4000 US Dollars). they changed the brake bump for 10000 (around 2500 UD dollars).
When I changed my brake pads and turned on the car, I received that message with beeping sound, then I removed those wires and it is all gone.
Take the car to Dubai even if it is imported they will fix it for you because this is a recall and they had to change it. I tool mine to Sharjah they refused to fix it, then I wrote a complaint message and sent it to the GM of Dubai CCing their Customer Relations. It was unbeleivable the service manager called me (he is German) and appologised and told me to get him the car.
They fixed many things for free and did all the recalls, the whole job was worth around 15,000 AED (more than 4000 US Dollars). they changed the brake bump for 10000 (around 2500 UD dollars).
#41
Out Of Control!!
Join Date: Jul 2003
Location: North Scottsdale, AZ
Posts: 15,903
Received 4,440 Likes
on
3,153 Posts
'71 Pinto
Originally Posted by Tariq
After i replace the Sensor, i drove the car and pushed the brake , i made a trip and keep pushing, but the warning still appear!...
Inspect the PB cable for evidence of chafing in the area of the fuel tank retaining strap (both sides of drive shaft). Vibrations due to driving create a relative motion between the PB cable and the fuel tank retaining strap. In extreme cases, the sheathing of the cable may become chafed allowing water to enter the cable assembly which may lead to corrosion of the cable.
#43
Out Of Control!!
Join Date: Jul 2003
Location: North Scottsdale, AZ
Posts: 15,903
Received 4,440 Likes
on
3,153 Posts
'71 Pinto
Originally Posted by byttcool99
Just remove the wires, don't replace them
![Roll Eyes (Sarcastic)](https://mbworld.org/forums/images/smilies/rolleyes.gif)
Edge Guard A001 987 76 25
PB Cable (left) A211 420 02 85
PB Cable (right) A211 420 03 85
#44
Super Member
Thread Starter
Guys,
I toke my car to the workshop, they informed me that, the problem mainly comes from the SBC !,,, yes correct that about 3 workshop said the same after connect the car with DAS.
The workshop is going to change that part under waranty, I wonder what make my SBC like this, i hope someone can tell the reason in order to aware from braking any more...
I toke my car to the workshop, they informed me that, the problem mainly comes from the SBC !,,, yes correct that about 3 workshop said the same after connect the car with DAS.
The workshop is going to change that part under waranty, I wonder what make my SBC like this, i hope someone can tell the reason in order to aware from braking any more...
#45
Super Member
Thread Starter
Finally, its over, i picked my car today with new SBC system, i notice big diffrent in braking than before, its smooth and no need to push the padle more,, generally its amazing than the old version 2003 models... after modified.
but once i take out my car, i turn on the audio it shows me only Mercedes benz logo , then it turn off , the workshop closed agine.. hope someone can advise what is the problem agine...
attached herewith photos of the SBC i notice it looks diffrent than the old one...
Comments please..
but once i take out my car, i turn on the audio it shows me only Mercedes benz logo , then it turn off , the workshop closed agine.. hope someone can advise what is the problem agine...
attached herewith photos of the SBC i notice it looks diffrent than the old one...
Comments please..
#47
Super Member
Join Date: Dec 2003
Location: ct
Posts: 522
Likes: 0
Received 2 Likes
on
2 Posts
All Diesel Fleet !1983 240d stick,2005 E320 CDI Midnight blue, 2005 E320 CDI, Desert Silver, Kubota
Again, Worldwide MB Maintenance Training Problems
MB needs to assess its' maintenance. Maybe it is just too big a problem to keep up with sophisticated computer dominated automobiles. But they make them, so they are supposed to be able to fix them. Someone needs to take charge of maintenance. Should we do a J.D. Power maintenance survey?
#48
Originally Posted by jimbo1mcm
MB needs to assess its' maintenance. Maybe it is just too big a problem to keep up with sophisticated computer dominated automobiles. But they make them, so they are supposed to be able to fix them. Someone needs to take charge of maintenance. Should we do a J.D. Power maintenance survey?
If only they'd put in a USB port and make the software updates downloadable...
#49
MBWorld Fanatic!
Join Date: Mar 2004
Location: Ft. Lauderdale Area, USA
Posts: 5,017
Likes: 0
Received 15 Likes
on
15 Posts
2015 ML 350
Sounds like you are a little ticked at the stupid & second rate electronics/software. I am too. I love the way the car feels and looks, but its in the damn shop for idiotic problems far, far too often. The glow is starting to come off the vehicle's ownership experience.
#50
Newbie
Join Date: Jun 2014
Location: UAE
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
W211 E500 05'
Well, I got that exact message as well.
Took it to the dealer. They said it's the SBC High Pressure Reservoir, which is not covered by the 10 years warranty. (Only the SBC Pump is covered).
Paid 1100$ to replace the reservoir, and the message is cleared now.
I drive an E500 05' with 180k km on it.
Took it to the dealer. They said it's the SBC High Pressure Reservoir, which is not covered by the 10 years warranty. (Only the SBC Pump is covered).
Paid 1100$ to replace the reservoir, and the message is cleared now.
I drive an E500 05' with 180k km on it.