P0410 on S600 getting frustrated...
Super Member
Joined: Dec 2007
Posts: 980
Likes: 224
2005 S500 Designo
Here’s the solenoid valve:
https://www.mboemparts.com/oem-parts...lve-0025407097
https://www.mboemparts.com/oem-parts...lve-0025407097
Super Member
Joined: Dec 2007
Posts: 980
Likes: 224
2005 S500 Designo
After replacing the solenoid valve I’m still goetting the stupid p0410 code.
I think I just want to code all that **** out. idgaf. Is there a procedure someone has come up with to do that? are there side effects?
I think I just want to code all that **** out. idgaf. Is there a procedure someone has come up with to do that? are there side effects?
MBWorld Fanatic!
Joined: Dec 2012
Posts: 2,473
Likes: 439
From: Ball Ground, GA (N of Atlanta)
2003 S500 2007 GL450
Yes, you can go into developer mode on DAS and tell the emissions system to ignore the Secondary Air Injection system and codes. Np problem passing emissions inspections, no CHECK ENGINE light, etc.
MBWorld Fanatic!
Joined: Dec 2012
Posts: 2,473
Likes: 439
From: Ball Ground, GA (N of Atlanta)
2003 S500 2007 GL450
I can't guarantee that this is absolutely correct, but it should help get you close, anyway.
Start XENTRY, enter your VIN, start DAS.
Go to CONTROL UNITS
Go to DRIVE
Go to MESFI
Go to DEVELOPMENT DATA
Go to CONTROL UNIT ADAPTATIONS
Go to CONTROL UNIT ADAPTATIONS (VARIANT CODING)
Go to IMPLIZITE KODIERUNG SECONDARY AIR INJECTION
Scroll down to 0178
Change DIAGNOSE EIN to DIAGNOSE AUS
You may need to save...
Let us know how this works out.
Start XENTRY, enter your VIN, start DAS.
Go to CONTROL UNITS
Go to DRIVE
Go to MESFI
Go to DEVELOPMENT DATA
Go to CONTROL UNIT ADAPTATIONS
Go to CONTROL UNIT ADAPTATIONS (VARIANT CODING)
Go to IMPLIZITE KODIERUNG SECONDARY AIR INJECTION
Scroll down to 0178
Change DIAGNOSE EIN to DIAGNOSE AUS
You may need to save...
Let us know how this works out.
Super Member
Joined: Dec 2007
Posts: 980
Likes: 224
2005 S500 Designo
I can't guarantee that this is absolutely correct, but it should help get you close, anyway.
Start XENTRY, enter your VIN, start DAS.
Go to CONTROL UNITS
Go to DRIVE
Go to MESFI
Go to DEVELOPMENT DATA
Go to CONTROL UNIT ADAPTATIONS
Go to CONTROL UNIT ADAPTATIONS (VARIANT CODING)
Go to IMPLIZITE KODIERUNG SECONDARY AIR INJECTION
Scroll down to 0178
Change DIAGNOSE EIN to DIAGNOSE AUS
You may need to save...
Let us know how this works out.
Start XENTRY, enter your VIN, start DAS.
Go to CONTROL UNITS
Go to DRIVE
Go to MESFI
Go to DEVELOPMENT DATA
Go to CONTROL UNIT ADAPTATIONS
Go to CONTROL UNIT ADAPTATIONS (VARIANT CODING)
Go to IMPLIZITE KODIERUNG SECONDARY AIR INJECTION
Scroll down to 0178
Change DIAGNOSE EIN to DIAGNOSE AUS
You may need to save...
Let us know how this works out.
I’ll give it a shot once I get the chance. I ordered a secondary air relay that apparently causes issues on these. If that doesn’t kill the CEL, I’ll ignore the entire secondary air system, although I’m a little bit hesitant, b/c I don’t want to fry my cats.
MBWorld Fanatic!
Joined: Dec 2012
Posts: 2,473
Likes: 439
From: Ball Ground, GA (N of Atlanta)
2003 S500 2007 GL450
There should be no danger of affecting the cats. The Secondary Air Injection System functions only a fraction of the run time, and is not required for the car to meet emission standards - it just makes the car "ultra-low emissions". If you tell the computer to not bother checking the system, it will no longer give you a CEL / MIL / CHECK ENGINE LIGHT, so you can pass the standard emissions tests.
