2015 S Class Sedan: Looking for trunk umbrella holder
#1
Newbie
Thread Starter
Join Date: Jun 2016
Location: Peabody, Massachusetts
Posts: 3
Likes: 0
Received 1 Like
on
1 Post
2015 Mercedes-Benz S550 4Matic Sedan
2015 S Class Sedan: Looking for trunk umbrella holder
My car is a 2015 Mercedes S550 4Matic Sedan. Past models had a trunk mounted clip/bracket to hold an umbrella. I can't seem to find one of those that will fit my model.
Does anyone have any idea if it exists for this model and year? How can I find one if it does exist?
Thanks in advance.
Don
Looks something like this.....
Does anyone have any idea if it exists for this model and year? How can I find one if it does exist?
Thanks in advance.
Don
Looks something like this.....
The following users liked this post:
Jim Ma (05-27-2021)
#2
Out Of Control!!
Join Date: Jul 2003
Location: North Scottsdale, AZ
Posts: 15,903
Received 4,446 Likes
on
3,154 Posts
'71 Pinto
Same part # 2218101214 as previous w221 https://mbworld.org/forums/s-class-w...ml#post6728970
The following users liked this post:
hstmercedes (06-28-2016)
#3
Newbie
Thread Starter
Join Date: Jun 2016
Location: Peabody, Massachusetts
Posts: 3
Likes: 0
Received 1 Like
on
1 Post
2015 Mercedes-Benz S550 4Matic Sedan
Thank you....,
Thank you, I didn't think they were offering it as an option any more.
I'll order one and try to install it myself. I appreciate your response.
Cordially,
Don
I'll order one and try to install it myself. I appreciate your response.
Cordially,
Don
#4
MBWorld Fanatic!
Join Date: Oct 2010
Location: Corona Del Mar, CA
Posts: 7,435
Received 3,729 Likes
on
2,130 Posts
2020 S560 Sedan, 2019 SL450, 2019 E450 Luxury Trim Wagon, '24 BMW I7 on order...
I always wondered what that thing was for.
#5
Confirmation
So I did it! I recently traded in my W221 and purchased a 2015 W222. With that, I removed my umbrella holder from the W221 and successfully installed it in my W222. I have a post on the W221 forum with the part numbers of everything I used, and everything transferred over with no issues to my W222. Below are the pictures:
The following users liked this post:
SwineHund550 (10-13-2018)
#6
MBWorld Fanatic!
Thanks for putting your insights, I didn't know S Class had that option . However, that makes me ask a question : Where's that umbrella ?
#7
Member
Were the holes already in the trunk lid inner steel panel on the W222 like they were on the W221, or did you have to create the holes? When I installed this on my W221, the holes were already stamped out of the sheet metal. It made installation very simple.
Trending Topics
#8
Installation was exactly as it was for the W221. The holes are already stamped out of the sheet metal just like it was with the W221; insert the treenails into the holes to catch the screws, make the holes through the liner and screw the holder into place.....done!
#10
MBWorld Fanatic!
#11
MBWorld Fanatic!
It’s rare that I ever saw any w221 with this. I think it’s a port installed thing. Like an accessory item. Also haven’t seen any w222 with it yet.
Whats cost???
Whats cost???
#12
Out Of Control!!
Join Date: Jul 2003
Location: North Scottsdale, AZ
Posts: 15,903
Received 4,446 Likes
on
3,154 Posts
'71 Pinto
$20 - $30
#14
I just bought one of these from ebay.. Did you have to pull the liner? Cut slots in the liner for the tabs? Were they marked on the back side of the liner?
#15
Out Of Control!!
Join Date: Jul 2003
Location: North Scottsdale, AZ
Posts: 15,903
Received 4,446 Likes
on
3,154 Posts
'71 Pinto
Mounts on trunk lid panel using treenail part #6399980185 (210 in diagram), and screw 4.2x25 # 000000000525 (220). See attachment.
The following 3 users liked this post by konigstiger:
#16
Yes, I pulled the liner back just a bit, from the bottom, where you will see two square holes centered. Those square holes are where you put the treenails to catch the two screws. I measured distance from square holes to the plastic rivet holes on both sides and poked through with a screwdriver. FYI, you will also have to remove the two plastic "arm covers" #130 in the diagram above to be able to peel liner back. Hope this helps....
The following users liked this post:
Texas 550 (05-15-2024)
#17
MBWorld Fanatic!
My friend has one of these from his old w221 that he said he'd GIVE TO ME. He just has the holder piece and no screws. I have a lot of screws in my parts bin, etc. If I only have the back holder that he gives me, do I need anything special to attach it besides some basic screws??? Hope someone can answer this.
The following users liked this post:
Texas 550 (05-15-2024)
#19
MBWorld Fanatic!
#21
I'm going to see if I can 3d print a couple of those.
[QU
OTE=Jason B;7557810] google shows this...
I bet I have something else that will work laying around that's similar...... hmm[/QUOTE]
[QU
OTE=Jason B;7557810] google shows this...
I bet I have something else that will work laying around that's similar...... hmm[/QUOTE]
#22
MBWorld Fanatic!
#23
#24
MBWorld Fanatic!
#25