All part numbers needed for e63 conversion look inside
209-820-07-56 Fog Lamp Left $202.00
209-820-08-56 Fog Lamp Right $202.00
211-520-15-22 Engine Undertray $240.00
211-820-09-21 Bumper Blinker Left $37.00
211-820-10-21 Bumper Blinker Right $37.00
211-880-17-83-9040 Grill (Non Distronic) $306.00
211-880-18-83-9040 Grill w/Distronic $825.00
211-880-17-05-9999 Headlamp Washer Cover Left $26.00
211-880-18-05-9999 Headlamp Washer Cover Right $26.00
211-880-07-03 Center Inner Plastic Support $16.50
211-880-09-03 Inner Plastic Support Left $36.00
211-880-10-03 Inner Plastic Support Right $36.00
211-885-40-25 Bumper Cover (Cars w/headlight washers) $1420.00
211-885-10-22-9040 Tow Hook Cover Black $39.50
211-885-23-21 Chrome Trim For Bumper Left $40.00
211-885-24-21 Chrome Trim For Bumper Right $40.00
211-885-13-53 Center Mesh $160.00
211-885-17-53 Fog Light Surround Left $145.00
211-885-18-53 Fog Light Surround Right $145.00
211-885-13-37 Impact Absorber Center $26.00
211-885-15-37 Impact Absorber Left $24.50
211-885-16-37 Impact Absorber Right $24.50
211-885-03-16 Reinforcement For Lower Bumper center $28.50 (This part bonds to the inside of the bumper on the lower center I would use window urethane
to bond to bumper)
211-885-05-16 $12.50 reinforcement for left side of bumper lower
211-885-06-16 $12.50 reinforcement for right side of bumper lower
211-885-07-16 Reinforcement For Lower Bumper $25.00 (This part bonds to the inside of the bumper on the lower Left side I would use window urethane to bond to bumper)
211-885-08-16 Reinforcement For Lower Bumper $25.00 (This part bonds to the inside of the bumper on the lower Right I would use window urethane to bond to bumper)
211-887-03-27 Pull For Hood Latch $5.50 (This replaces pull on E55 hood latch)
002-998-51-81 Retaining Clip For Mesh $5.31 (Order 6)
003-994-05-45 Speed Nut For Fog Surround $2.00 (Order 6)
000000-000479 Screw For Fog Surround $1.70 (Order 6)
003-994-86-45 Speednut For Foglight $0.70 (Order 8)
000000-000521 Screw For Foglight $0.70 (Order 8)
000-990-54-92-9051 rivet .98 (Order 6)
Any other items you will need will be taken off your old bumper "clips hardware and washer springs" feel free to ask me any questions about the conversion this is not for a Parktronic car. Photos to follow.
Trending Topics
The Best of Mercedes & AMG






it was exactly that type of stand that i had my bumper on when a gust of wind blew it to the floor!
Last edited by Alps; Oct 12, 2010 at 06:24 AM.





Ive done with Parktronic, you have to change the parking sensor brackets to ones from a w171, part numbers A171 885 00 14 (x6), this will allow you to fit your exisiting sensors on.
good luck!











