Aeroforce interceptor problem
#1
MBWorld Fanatic!
Thread Starter
Aeroforce interceptor problem
I installed my aeroforce interceptor gauge a few days ago. It ran great for 1 day. Then, it would start up and shut down and start up ... It keeps restarting over and over again. Anyone here know the solution?
#2
MBWorld Fanatic!
Join Date: Dec 2011
Location: new ringgold pa
Posts: 1,482
Likes: 0
Received 25 Likes
on
24 Posts
99 ford lightning
check all your connections, if not get a hold of mike at aeroforce he will take care of it i had two small problems with mine and he fixed them and got it back to me fast.
#3
MBWorld Fanatic!
Thread Starter
Thanks, yes I sent them an email. I was thinking if someone here had the same issue and knew of a solution that I could perform.
#4
MBWorld Fanatic!
Thread Starter
So far, no solution from aeroforce. I am disappointed with their customer service. I am told to change the parameters of the gauge. I have already told them that is not possible as the gauge is stuck on start and restart. I have followed up with them 2x and no response. It pisses me off when I have to chase the vendor for a solution to their product.
#6
MBWorld Fanatic!
Thread Starter
#7
MBWorld Fanatic!
Sorry for your troubles...
OT - Has anyone made a really nice face plate to cover the ash tray ? I would like to mount a switch and a gauge in the cubby...
OT - Has anyone made a really nice face plate to cover the ash tray ? I would like to mount a switch and a gauge in the cubby...
Trending Topics
#10
MBWorld Fanatic!
Thread Starter
No solution proposed by Aeroforce, so far. I hate it when I have to chase the vendor for a solution to a problem with their product.
#12
Super Member
Join Date: Mar 2011
Location: Porter Ranch, CA
Posts: 502
Likes: 0
Received 0 Likes
on
0 Posts
E55, CTS-V Wagon, Duc 1098R
The only issue I had that resembled this was when I had too many pids selected. It was as if the refresh rate was too slow and the software would reset because it wasn't getting the data in time. It seemed like it preferred 5 or less pids only though the OBD.
#13
MBWorld Fanatic!
#15
MBWorld Fanatic!
Thread Starter
Looks like my aeroforce gauge broke again. The same problem back in January of this year (just keeps restarting) has returned. I am sending it back to aeroforce to have it fixed, but just a pain. Great product and concept. It really gives you a better connection and sense of what your car is doing (like detecting knock). But, 2x same problem in 10 months. Anybody else had to 2x sent their Aeroforce gauge back for repairs?
#16
MBWorld Fanatic!
Join Date: Dec 2011
Location: new ringgold pa
Posts: 1,482
Likes: 0
Received 25 Likes
on
24 Posts
99 ford lightning
I have one thing todd told me was to unplug it if the car sits a while and the battery goes low or if you try to start it while jumping it. I keep my car with a tender on it have not had a issue since.
#17
Super Member
Had mine for 7 months until it went out. Sending it off and spending 60 bucks to fix their problem is complete bs. Then again, I have no other option for this type of gauge.
#21
MBWorld Fanatic!
Thread Starter
I don't disagee with you. And, my aeroforce broke again...this is the new one they sent me about +1 month ago. Urgh...my problem is that I also purchased a pillar gauge holder to hold the Aeroforce gauge. Is there a competitor to aeroforce? Great gauge but constant breaks down.
#22
MBWorld Fanatic!
Thread Starter
I give up on aeroforce gauge. Great idea but repeated failures and extra money in me shipping the gauge back to them each time has taken its toll. I am now looking at nGauge or dashdaq xl.