P0012 - Camshaft Position - Timing Over-Retarded (Bank 1)
#1
Super Member
Thread Starter
Join Date: Jul 2006
Location: The OC
Posts: 749
Likes: 0
Received 0 Likes
on
0 Posts
2006 C230SS & 2009 E350
P0012 - Camshaft Position - Timing Over-Retarded (Bank 1)
Folks,
I got CEL this morning so I call stealership and they told me it was probably the gas cap. Still curious and wasn't satisfied so I went to Autozone to borrow the scanner and got P0012 error code.
What is this error? I know it's something with camshaft but what cause it? Car is going to dealer tomorrow morning, but some feedback will be greatly appreciated.
I got CEL this morning so I call stealership and they told me it was probably the gas cap. Still curious and wasn't satisfied so I went to Autozone to borrow the scanner and got P0012 error code.
What is this error? I know it's something with camshaft but what cause it? Car is going to dealer tomorrow morning, but some feedback will be greatly appreciated.
#2
MBWorld Fanatic!
Probably a bad
camshaft position sensor.You would have real problems if the cam was over retarded.
Is it running fine?Are you under warranty?
ohlord
Is it running fine?Are you under warranty?
ohlord
#4
MBWorld Fanatic!
#5
Super Member
Thread Starter
Join Date: Jul 2006
Location: The OC
Posts: 749
Likes: 0
Received 0 Likes
on
0 Posts
2006 C230SS & 2009 E350
Got the car back last night. It was the sensor and adjustment that they had to do. After driving it last night, the engine feels smoother now.
#6
MBWorld Fanatic!
Great
camshaft position sensor is a whole lot better then hearing it was the timing chain
thanks for the update.
ohlord
thanks for the update.
ohlord
The following users liked this post:
Icelandicbenz19 (02-05-2021)
#7
Trending Topics
#8
Super Member
Thread Starter
Join Date: Jul 2006
Location: The OC
Posts: 749
Likes: 0
Received 0 Likes
on
0 Posts
2006 C230SS & 2009 E350
#9
Super Member
Join Date: Oct 2007
Location: Charlotte, NC
Posts: 537
Likes: 0
Received 2 Likes
on
2 Posts
2013 S550, CLS500, ‘03 SL500, “92 190E Sportline
How can the camshaft position sensor be replaced? (DIY)
Sometimes, at startup my car shakes a little, but after a few seconds idles smoothly. I'm thinking it could be the camshaft sensor.
I already replaced the cam sensors and added the isolation wires in summer 2008.
Sometimes, at startup my car shakes a little, but after a few seconds idles smoothly. I'm thinking it could be the camshaft sensor.
I already replaced the cam sensors and added the isolation wires in summer 2008.
#10
Super Moderator
#11
yesterday i got a code P0340 cam position sensor A bank 1 cicuit malfunction. long story short - i drove right to the dealer as the car had real rough idle. called me today to tell me they installed a NEW cam sensor and car acted the same. Put old sensor back in and now checking the chain slack after removing the valve cover. its the M271 engine with 70k on it. i am getting nervous.......
#12
Super Moderator
Join Date: Dec 2006
Location: Camas, WA
Posts: 2,403
Likes: 0
Received 58 Likes
on
24 Posts
2007 C230SS; 2014 ML350 BT
This code just popped up on my 07 C230 tonight. The code scanner read: P0012 - A camshaft position timing over - retarded bank 1.
This is just my luck. I am 7K miles out of warranty. Anyone know how to test the sensor, or how much it runs? Sounds like it needs adjustment from what SlvrC230SS reported back from his dealer. Can this be done DIY, or am I going to have to bend over and take it to the dealer?
This is just my luck. I am 7K miles out of warranty. Anyone know how to test the sensor, or how much it runs? Sounds like it needs adjustment from what SlvrC230SS reported back from his dealer. Can this be done DIY, or am I going to have to bend over and take it to the dealer?
#13
Super Moderator
John,
I pulled my first 112 based comments because they were crap as you will see. I have a 5 meg doc for you - PM me your e mail address. The quadcam engine looks like a bugger with 4 cam sensors. You might want to leave this to a dealer or get an R&R method from splinter.
Bad day - after late night - suffering brain fade. talking about 271 when I mean 112 - Yugh!
I pulled my first 112 based comments because they were crap as you will see. I have a 5 meg doc for you - PM me your e mail address. The quadcam engine looks like a bugger with 4 cam sensors. You might want to leave this to a dealer or get an R&R method from splinter.
Bad day - after late night - suffering brain fade. talking about 271 when I mean 112 - Yugh!
Last edited by Glyn M Ruck; 09-29-2009 at 07:15 AM.
#14
Super Moderator
Join Date: Dec 2006
Location: Camas, WA
Posts: 2,403
Likes: 0
Received 58 Likes
on
24 Posts
2007 C230SS; 2014 ML350 BT
OK, so I cleared the code and am going to drive it and see if it pops up again. Car runs fine, so no other symptoms. Though, just a note, but don't think it matters, the car is currently filled with E85 and has been the last 4 tankfuls.
Glyn, I PM'ed you my email address. I am going to order the MB service manual DVD today, so I can get a better idea of what's involved. Thanks for the help.
I seemed to have gotten the C-Class that has all the rare problems 1st the steering rack, now this.
Glyn, I PM'ed you my email address. I am going to order the MB service manual DVD today, so I can get a better idea of what's involved. Thanks for the help.
I seemed to have gotten the C-Class that has all the rare problems 1st the steering rack, now this.
#15
Super Moderator
Found your e mail address - doc sent - let me know if received OK. I also have a Merc general principles doc if you are interested - not on our engines though.
#16
Super Moderator
The E85 won't have had anything to do with this. They are all just hall sensors - even on the 112 where it just senses Cyl No 1.
#17
Super Moderator
Join Date: Dec 2006
Location: Camas, WA
Posts: 2,403
Likes: 0
Received 58 Likes
on
24 Posts
2007 C230SS; 2014 ML350 BT
Glyn, I got the doc. I have read that one several times Thanks.
Drove to work (40 miles), and no light. What are the chances it was a fluke and won't come back?
Looking at the documents on the M272 and looking at the engine last night, If I do have to replace 1 of the 4 sensors, it will be a total cake walk. They are right there on the front of the engine. 5 minutes at most to replace one. I can't imagine there being a way to adjust them, as the bolt holes aren't slotted or anything. Just may have to "learn" them in STAR as you stated Glyn. But, even that seems really unlikely, based on their function.
Ordered the STAR service manual DVD from MBUSA. $85 and it will be here Friday. $60 for the DVD, $10 s/h, $5 to expedite, and tax.
According to STAR EPC, there is 1 part# for the sensor on M272 engines, and there is 4 of the same sensor total. Part number: A004-153-96-28 It lists for $222.00 MB of Ft. Lauderdale has it for $173.16.
Drove to work (40 miles), and no light. What are the chances it was a fluke and won't come back?
Looking at the documents on the M272 and looking at the engine last night, If I do have to replace 1 of the 4 sensors, it will be a total cake walk. They are right there on the front of the engine. 5 minutes at most to replace one. I can't imagine there being a way to adjust them, as the bolt holes aren't slotted or anything. Just may have to "learn" them in STAR as you stated Glyn. But, even that seems really unlikely, based on their function.
Ordered the STAR service manual DVD from MBUSA. $85 and it will be here Friday. $60 for the DVD, $10 s/h, $5 to expedite, and tax.
According to STAR EPC, there is 1 part# for the sensor on M272 engines, and there is 4 of the same sensor total. Part number: A004-153-96-28 It lists for $222.00 MB of Ft. Lauderdale has it for $173.16.
Last edited by johnand; 09-29-2009 at 10:40 AM.
#18
Banned
Join Date: Apr 2008
Location: In Kush Land So cal
Posts: 910
Likes: 0
Received 2 Likes
on
2 Posts
02 C320 Sedan
Glyn, I got the doc. I have read that one several times Thanks.
Drove to work (40 miles), and no light. What are the chances it was a fluke and won't come back?
Looking at the documents on the M272 and looking at the engine last night, If I do have to replace 1 of the 4 sensors, it will be a total cake walk. They are right there on the front of the engine. 5 minutes at most to replace one. I can't imagine there being a way to adjust them, as the bolt holes aren't slotted or anything. Just may have to "learn" them in STAR as you stated Glyn. But, even that seems really unlikely, based on their function.
Ordered the STAR service manual DVD from MBUSA. $85 and it will be here Friday. $60 for the DVD, $10 s/h, $5 to expedite, and tax.
According to STAR EPC, there is 1 part# for the sensor on M272 engines, and there is 4 of the same sensor total. Part number: A004-153-96-28 It lists for $222.00 MB of Ft. Lauderdale has it for $173.16.
Drove to work (40 miles), and no light. What are the chances it was a fluke and won't come back?
Looking at the documents on the M272 and looking at the engine last night, If I do have to replace 1 of the 4 sensors, it will be a total cake walk. They are right there on the front of the engine. 5 minutes at most to replace one. I can't imagine there being a way to adjust them, as the bolt holes aren't slotted or anything. Just may have to "learn" them in STAR as you stated Glyn. But, even that seems really unlikely, based on their function.
Ordered the STAR service manual DVD from MBUSA. $85 and it will be here Friday. $60 for the DVD, $10 s/h, $5 to expedite, and tax.
According to STAR EPC, there is 1 part# for the sensor on M272 engines, and there is 4 of the same sensor total. Part number: A004-153-96-28 It lists for $222.00 MB of Ft. Lauderdale has it for $173.16.
Oh snaps when you get that cd... do us all a favor and put it up as a torrent =P
Sucks to hear your 07 is out of warranty which is crazy..
#19
Super Moderator
Glyn, I got the doc. I have read that one several times Thanks.
Drove to work (40 miles), and no light. What are the chances it was a fluke and won't come back?
Looking at the documents on the M272 and looking at the engine last night, If I do have to replace 1 of the 4 sensors, it will be a total cake walk. They are right there on the front of the engine. 5 minutes at most to replace one. I can't imagine there being a way to adjust them, as the bolt holes aren't slotted or anything. Just may have to "learn" them in STAR as you stated Glyn. But, even that seems really unlikely, based on their function.
Ordered the STAR service manual DVD from MBUSA. $85 and it will be here Friday. $60 for the DVD, $10 s/h, $5 to expedite, and tax.
According to STAR EPC, there is 1 part# for the sensor on M272 engines, and there is 4 of the same sensor total. Part number: A004-153-96-28 It lists for $222.00 MB of Ft. Lauderdale has it for $173.16.
Drove to work (40 miles), and no light. What are the chances it was a fluke and won't come back?
Looking at the documents on the M272 and looking at the engine last night, If I do have to replace 1 of the 4 sensors, it will be a total cake walk. They are right there on the front of the engine. 5 minutes at most to replace one. I can't imagine there being a way to adjust them, as the bolt holes aren't slotted or anything. Just may have to "learn" them in STAR as you stated Glyn. But, even that seems really unlikely, based on their function.
Ordered the STAR service manual DVD from MBUSA. $85 and it will be here Friday. $60 for the DVD, $10 s/h, $5 to expedite, and tax.
According to STAR EPC, there is 1 part# for the sensor on M272 engines, and there is 4 of the same sensor total. Part number: A004-153-96-28 It lists for $222.00 MB of Ft. Lauderdale has it for $173.16.
Disgusting price for a simple hall sensor!
Edit - regarding code not returning - anything is possible with Benz electronics. One off triggers are common.
Last edited by Glyn M Ruck; 09-29-2009 at 06:47 PM.
#21
Super Moderator
#23
Super Moderator
Join Date: Dec 2006
Location: Camas, WA
Posts: 2,403
Likes: 0
Received 58 Likes
on
24 Posts
2007 C230SS; 2014 ML350 BT
Thanks Glyn. 150 miles now since the reset and no light. Just going to sit tight for now and see if it returns before doing anything.
#24
Super Moderator
Yeah - A number of years back when we sponsored & I ran the Caltex Honda Race Team in SA it came to my notice that the markup on Honda motorcycle spares was 1200%, yes 1200%. Had a fight with the MD of the importer's. I informed him that the race team would not be paying these prices. He could have landed cost plus 10% from us. Made a big difference to my racing budget.
#25
Super Moderator
Join Date: Dec 2006
Location: Camas, WA
Posts: 2,403
Likes: 0
Received 58 Likes
on
24 Posts
2007 C230SS; 2014 ML350 BT
OK, CEL on again today, same P0012 code. Only problem, is the code scanner I have is generic, and the only indicated of which 1 of 4 to replace is "bank 1". The STAR WIS manual, gives me no indicator of which one either. I rather not have to find out which one by trial and error. Anyone have any idea what MB considers bank 1, or any other help figuring out which one?
Ordering a new sensor today.
Ordering a new sensor today.