ABC pulsation damper and Filter DIY repair
#1
Member
Thread Starter
Join Date: Jun 2011
Posts: 163
Received 0 Likes
on
0 Posts
2003 C32, 2002 S55, 1999 SL500, 2004 S430
ABC pulsation damper and Filter DIY repair
The suspension pulsation damper will cause a humming / buzzing noise when not working correctly.
See TSB Topic number LI32.50-P-048280 for more detailed information.
Not every thing I do is according to the strict guidelines of WIS, so use my directions at your own risk.
Jack up front end. Find the 2 bleed screws on the LF and RF next to the torque strut bushing and bleed the system. Make sure you have the car secure because you will lose all suspension pressure after this is done.
Remove the pulsation damper. You will need a 24MM wrench for this, because of how the threads are welded to the unit you can't fit the wrench in every position. Maybe you can take this off with a oil filter remover?
This is a good time to change your filter for the suspension.
The top is held on by a hook, remove by pressing down on the spring.
My fluid was black so I pumped out what was in the res. try to be as clean as you can be.
Fill up res to the engine off min/max, install filter.
I started the car and set it to normal height, check fluid level at engine on min/max. Raise up then normal 15 times if any major components were replaced while checking fluid level only when set in the normal ride height level. If you hear a hissing noise in the area where you installed the pulsation damper or in the rear of your car then shut it off and bleed at the same bleed screws.
I had the hissing noise so I had to bleed the system 5 times. I had no luck getting rid of the noise. I ran the rodeo and dynamic test along with testing the pump and other components and had no codes after I was finished.
See TSB Topic number LI32.50-P-048280 for more detailed information.
Not every thing I do is according to the strict guidelines of WIS, so use my directions at your own risk.
Jack up front end. Find the 2 bleed screws on the LF and RF next to the torque strut bushing and bleed the system. Make sure you have the car secure because you will lose all suspension pressure after this is done.
Remove the pulsation damper. You will need a 24MM wrench for this, because of how the threads are welded to the unit you can't fit the wrench in every position. Maybe you can take this off with a oil filter remover?
This is a good time to change your filter for the suspension.
The top is held on by a hook, remove by pressing down on the spring.
My fluid was black so I pumped out what was in the res. try to be as clean as you can be.
Fill up res to the engine off min/max, install filter.
I started the car and set it to normal height, check fluid level at engine on min/max. Raise up then normal 15 times if any major components were replaced while checking fluid level only when set in the normal ride height level. If you hear a hissing noise in the area where you installed the pulsation damper or in the rear of your car then shut it off and bleed at the same bleed screws.
I had the hissing noise so I had to bleed the system 5 times. I had no luck getting rid of the noise. I ran the rodeo and dynamic test along with testing the pump and other components and had no codes after I was finished.
#2
Super Member
Two questions.
1. I can't find a pulsation damper for less than $350, and various older threads mention paying ~$150. Is this a supply and demand issue, where everyone is getting these replaced since the TSB, or is something else funny going on in the global ABC pulsation damper market?
2. Where are the pictures?! Pleeeaassseeeeeee I want to DIY this, and having these pictures will probably be very useful!
1. I can't find a pulsation damper for less than $350, and various older threads mention paying ~$150. Is this a supply and demand issue, where everyone is getting these replaced since the TSB, or is something else funny going on in the global ABC pulsation damper market?
2. Where are the pictures?! Pleeeaassseeeeeee I want to DIY this, and having these pictures will probably be very useful!
#3
MBWorld Fanatic!
Carbizindio seems like the pictures are no longer available. Would be nice if they were still available.
Fried chicken did you check http://www.autohausaz.com or http://www.ecstuning.com seems to me they were in the $150 to $170 range. There are actually (4) accumulators on the Mercedes S-Class with ABC suspension. On my car 2003 S500 the part numbers are 220 327 01 15 (2), 220 327 02 15 (1) and 220 320 04 15 (1). I believe the last one is the pulsation damper. It list on ecstuning for $164. and on autohausaz for $190. When you do your part number searches I have found that you get better results when there are no spacees left between the numbers.
Fried chicken did you check http://www.autohausaz.com or http://www.ecstuning.com seems to me they were in the $150 to $170 range. There are actually (4) accumulators on the Mercedes S-Class with ABC suspension. On my car 2003 S500 the part numbers are 220 327 01 15 (2), 220 327 02 15 (1) and 220 320 04 15 (1). I believe the last one is the pulsation damper. It list on ecstuning for $164. and on autohausaz for $190. When you do your part number searches I have found that you get better results when there are no spacees left between the numbers.
Last edited by ibeforreal; 05-28-2015 at 05:35 PM.
#7
Super Member
Carbizindio seems like the pictures are no longer available. Would be nice if they were still available.
Fried chicken did you check http://www.autohausaz.com or http://www.ecstuning.com seems to me they were in the $150 to $170 range. There are actually (4) accumulators on the Mercedes S-Class with ABC suspension. On my car 2003 S500 the part numbers are 220 327 01 15 (2), 220 327 02 15 (1) and 220 320 04 15 (1). I believe the last one is the pulsation damper. It list on ecstuning for $164. and on autohausaz for $190. When you do your part number searches I have found that you get better results when there are no spacees left between the numbers.
Fried chicken did you check http://www.autohausaz.com or http://www.ecstuning.com seems to me they were in the $150 to $170 range. There are actually (4) accumulators on the Mercedes S-Class with ABC suspension. On my car 2003 S500 the part numbers are 220 327 01 15 (2), 220 327 02 15 (1) and 220 320 04 15 (1). I believe the last one is the pulsation damper. It list on ecstuning for $164. and on autohausaz for $190. When you do your part number searches I have found that you get better results when there are no spacees left between the numbers.
I'm looking for the pulsation damper mentioned in TSB LI32.50-P0048280
Here's a link to it although I'm not 100% sure it will work:
http://www.revbase.com/BBBMotor/TSb/...dPdf?id=180082
It's a part that bolts pretty much directly onto the tandem pump.
Trending Topics
#9
Super Member
#12
Super Member
Just kidding, they are identical xD