NEW Style Sequential Blink LED Dynamic Turn Signal Light For Mercedes Benz with BLUE
#26
MBWorld Fanatic!
Thread Starter
Join Date: Nov 2003
Location: Earth
Posts: 2,211
Received 444 Likes
on
344 Posts
2015 C300 4Matic Sport
One of the iSincer signals had a loose frosted overlay inside.
It wasn't aligned properly and you could see the leds behind it. I just gave it a quick slap and that fixed the issue.
It wasn't aligned properly and you could see the leds behind it. I just gave it a quick slap and that fixed the issue.
Last edited by benzdude; 05-21-2019 at 02:31 PM.
The following 2 users liked this post by benzdude:
jevsays (06-30-2019),
Trappers101 (05-21-2019)
The following 3 users liked this post by C300AWD:
#32
MBWorld Fanatic!
Thread Starter
Join Date: Nov 2003
Location: Earth
Posts: 2,211
Received 444 Likes
on
344 Posts
2015 C300 4Matic Sport
I tapped it a couple of times to fix it.
The following users liked this post:
Trappers101 (05-24-2019)
#34
MBWorld Fanatic!
Thread Starter
Join Date: Nov 2003
Location: Earth
Posts: 2,211
Received 444 Likes
on
344 Posts
2015 C300 4Matic Sport
All done. I simply used a glue gun on the green (blue light) wire.
(I didn't realize that the drivers side mirror is bigger than the passenger side.)
Carbon fiber covers installed.
(I didn't realize that the drivers side mirror is bigger than the passenger side.)
Carbon fiber covers installed.
#36
MBWorld Fanatic!
Thread Starter
Join Date: Nov 2003
Location: Earth
Posts: 2,211
Received 444 Likes
on
344 Posts
2015 C300 4Matic Sport
HOW TO REMOVE OEM TURN SIGNAL WITHOUT BREAKING ANYTHING.
- After removing the two screws, unclip the bottom corner of the turn signal and lift it up about an inch.
- Move the end to edge of the cover.
- Pull back gently on the cover to allow the end of the turn signal to slide out.
- Install in reverse.
#37
You sir are a bad influence. My Mercedes bookmark folder is starting to grow with all the things that I want to add. First black chrome diamond front grill, then chrome delete, then black mirror covers to complete the night package look. Then vorsteiner vff 107 in Black. Then a C63 rear diffuser. That should about cover exterior. Not like there's anything left to cover LOL
The following users liked this post:
benzdude (05-24-2019)
The following users liked this post:
shivinate (06-13-2019)
#41
Did you get the carbon fibre slide-on covers or the entire housing replacement? I'm looking at adding these on mine after I put on night package finish (chrome delete, powder coating the stock rims in the same style, adding black mirror covers).
#42
When I take the LED harness out I see 4 terminal wires. Which do I connect to so that I don’t create a short?
Last edited by Ianinaurora; 05-26-2019 at 10:01 AM. Reason: More info
#44
MBWorld Fanatic!
Thread Starter
Join Date: Nov 2003
Location: Earth
Posts: 2,211
Received 444 Likes
on
344 Posts
2015 C300 4Matic Sport
Strip the end of the green wire, fold the bare wire in two and stick it in the blue wire side of this harness. Add some hot glue to keep it in place. That's all.
Last edited by benzdude; 05-26-2019 at 11:33 PM.
The following users liked this post:
benzdude (05-27-2019)
#47
Left Turn Signal Malfunctioning
Hey guys, I wired both the same way, but check out the issue I’m having with my left turn signal when locking the car along with indicating a left turn as shown in the videos (imgur - https://imgur.com/a/cFHxXvi [won’t let me upload videos through phone]) Is there any reason for this that I can fix? Or I need to contact the manufacturer.
Also noticed that both of my car key remotes all of a sudden are having their keystrokes go by unregistered from the car at times (will occasionally not recognize I clicked lock unlock etc) seemingly the same time I had these done, is there a correlation (is housing for remote’s IR in the driver’s side mirror?)
Thanks for any input :
Also noticed that both of my car key remotes all of a sudden are having their keystrokes go by unregistered from the car at times (will occasionally not recognize I clicked lock unlock etc) seemingly the same time I had these done, is there a correlation (is housing for remote’s IR in the driver’s side mirror?)
Thanks for any input :
Last edited by shivinate; 06-13-2019 at 04:40 AM.
#48
MBWorld Fanatic!
Thread Starter
Join Date: Nov 2003
Location: Earth
Posts: 2,211
Received 444 Likes
on
344 Posts
2015 C300 4Matic Sport
I decided to order completely new "carbon fiber" covers for a cleaner black look.
The seller included a set of OEM look led turn signals, but I will swap them with the black (blue) dynamic ones.
The seller included a set of OEM look led turn signals, but I will swap them with the black (blue) dynamic ones.
#49
Junior Member
Join Date: May 2019
Location: Ft Worth
Posts: 40
Likes: 0
Received 23 Likes
on
12 Posts
15' C300 4Matic
Hey guys, I wired both the same way, but check out the issue I’m having with my left turn signal when locking the car along with indicating a left turn as shown in the videos (imgur - https://imgur.com/a/cFHxXvi [won’t let me upload videos through phone]) Is there any reason for this that I can fix? Or I need to contact the manufacturer.
Also noticed that both of my car key remotes all of a sudden are having their keystrokes go by unregistered from the car at times (will occasionally not recognize I clicked lock unlock etc) seemingly the same time I had these done, is there a correlation (is housing for remote’s IR in the driver’s side mirror?)
Thanks for any input :
Also noticed that both of my car key remotes all of a sudden are having their keystrokes go by unregistered from the car at times (will occasionally not recognize I clicked lock unlock etc) seemingly the same time I had these done, is there a correlation (is housing for remote’s IR in the driver’s side mirror?)
Thanks for any input :