C32 Headers
#56
Evomike, I believe that the headers in the picture are not the ones that are currently being offered by EvoSport as mentioned previously. Are you now reproducing the original bespoke equal length headers instead of the one pictured in a prior post that look like the SuperSprints?
#57
MBWorld Fanatic!
Join Date: Jul 2004
Location: Diamond Bar & Anaheim, CA
Posts: 1,194
Likes: 0
Received 2 Likes
on
2 Posts
2003 C-Class Sportcoupe
C32 Headers
Originally Posted by Vadim @ evosport
The first version of our headers was "equal-length". They only worked well with resonator removed.
Our production version is un-equal length, similar to Supersprint. They work well with or our without resonator. They are made from aluminized steel and coated with HiTemp coating.
Our production version is un-equal length, similar to Supersprint. They work well with or our without resonator. They are made from aluminized steel and coated with HiTemp coating.
Link
#58
MBWorld Fanatic!
Thread Starter
Mike, made a mistake. Production version is posted above. They are unequal length and coated with HiTemp Titanium coating. They will only fit W203 V6s (240, 320, C32).
#62
MBWorld Fanatic!
Join Date: Jul 2004
Location: Diamond Bar & Anaheim, CA
Posts: 1,194
Likes: 0
Received 2 Likes
on
2 Posts
2003 C-Class Sportcoupe
Overdrive pulley system - larger crankshaft pulley, spins supercharger faster and higher boost = more HP. Some of them do not have a harmonic balancer, ie bad. Correct me if I'm wrong.
#64
MBWorld Fanatic!
Join Date: Jul 2004
Location: Diamond Bar & Anaheim, CA
Posts: 1,194
Likes: 0
Received 2 Likes
on
2 Posts
2003 C-Class Sportcoupe
FYI:
I am having custom equal length headers made for my ported and flowed C32 motor. They are different from previous headers in the following ways:
Larger primary tubing - better flow
Ceramic coated, thermobaric coated
Wrapped in heat resistant material
Equal length header design - more HP gain per dollar
On my car, they should provide an additional +25HP increase. They will make more HP gain than unequal length headers. Cost will be $1800 and it will take a few weeks to manufacture. They are probably going to be ready by Feb-March, about the same timeframe my swap will take place at HOP.
If anybody wants these headers for their W203 V6 (240, 320, or C32), contact me or Josh R at HOP. You can also visit HOP to check it out. More info and pictures will be provided when they are ready.
I am having custom equal length headers made for my ported and flowed C32 motor. They are different from previous headers in the following ways:
Larger primary tubing - better flow
Ceramic coated, thermobaric coated
Wrapped in heat resistant material
Equal length header design - more HP gain per dollar
On my car, they should provide an additional +25HP increase. They will make more HP gain than unequal length headers. Cost will be $1800 and it will take a few weeks to manufacture. They are probably going to be ready by Feb-March, about the same timeframe my swap will take place at HOP.
If anybody wants these headers for their W203 V6 (240, 320, or C32), contact me or Josh R at HOP. You can also visit HOP to check it out. More info and pictures will be provided when they are ready.
![thumbs](https://mbworld.org/forums/images/smilies/thumbsup.gif)
Originally Posted by Vadim @ evosport
Mike, made a mistake. Production version is posted above. They are unequal length and coated with HiTemp Titanium coating. They will only fit W203 V6s (240, 320, C32).
#65
Senior Member
Join Date: Dec 2004
Location: UK
Posts: 394
Likes: 0
Received 0 Likes
on
0 Posts
Obsidian E55
Vadim.
Will these manifolds fit a right hand drive "UK SPEC" C32 or will they interfere with any of the steering mechanisms or anything else ??
thx bud.
Also got any green panel filters for the sl55 boxes as ive done the swap.
TIA
Andy
Will these manifolds fit a right hand drive "UK SPEC" C32 or will they interfere with any of the steering mechanisms or anything else ??
thx bud.
Also got any green panel filters for the sl55 boxes as ive done the swap.
TIA
Andy
#66
Super Member
Join Date: Jun 2003
Location: bay area, california
Posts: 714
Likes: 0
Received 0 Likes
on
0 Posts
'14 428i M-Sport, '02 C32 AMG
Originally Posted by pshek
FYI:
I am having custom equal length headers made for my ported and flowed C32 motor. They are different from previous headers in the following ways:
Larger primary tubing - better flow
Ceramic coated, thermobaric coated
Wrapped in heat resistant material
Equal length header design - more HP gain per dollar
On my car, they should provide an additional +25HP increase. They will make more HP gain than unequal length headers. Cost will be $1800 and it will take a few weeks to manufacture. They are probably going to be ready by Feb-March, about the same timeframe my swap will take place at HOP.
If anybody wants these headers for their W203 V6 (240, 320, or C32), contact me or Josh R at HOP. You can also visit HOP to check it out. More info and pictures will be provided when they are ready.![thumbs](https://mbworld.org/forums/images/smilies/thumbsup.gif)
I am having custom equal length headers made for my ported and flowed C32 motor. They are different from previous headers in the following ways:
Larger primary tubing - better flow
Ceramic coated, thermobaric coated
Wrapped in heat resistant material
Equal length header design - more HP gain per dollar
On my car, they should provide an additional +25HP increase. They will make more HP gain than unequal length headers. Cost will be $1800 and it will take a few weeks to manufacture. They are probably going to be ready by Feb-March, about the same timeframe my swap will take place at HOP.
If anybody wants these headers for their W203 V6 (240, 320, or C32), contact me or Josh R at HOP. You can also visit HOP to check it out. More info and pictures will be provided when they are ready.
![thumbs](https://mbworld.org/forums/images/smilies/thumbsup.gif)
sounds like a nice project. keep us updated. are they longtubes? would u mind sharing the diameter of the primaries?
#69
MBWorld Fanatic!
Join Date: Jul 2004
Location: Diamond Bar & Anaheim, CA
Posts: 1,194
Likes: 0
Received 2 Likes
on
2 Posts
2003 C-Class Sportcoupe
shorty unequal length headers
Update:
The header design was revised after talking with Josh R. They are going to be unequal length shorty headers. Everything else has remained unchanged, except the cost. They will cost $1150. Josh said that the equal length headers would provide only a marginally higher HP gain than the unequal length, about 3HP difference. The cost to produce equal length headers would be a few hundred dollars more, about $1800 for the equal length headers. They are going to be made of mild steel, with a ceramic outside coating and thermobaric inside coating. Hopefully with the lower price, people might be more interested. I'm still going to get a set for myself.![Smilie](https://mbworld.org/forums/images/smilies/smile.gif)
Oh yeah, the primary tube diameter will be 1.75 inches in diameter. The primary tubes on the Evosport shorty headers are 1.625 inches in diameter. Larger primary tubes are better for FI motors.
For more info or to get a group buy together, you can contact me or Josh R. I will try and keep this project updated continually.
Regarding an ECU retune, I'm not sure about that, but I can ask.
The header design was revised after talking with Josh R. They are going to be unequal length shorty headers. Everything else has remained unchanged, except the cost. They will cost $1150. Josh said that the equal length headers would provide only a marginally higher HP gain than the unequal length, about 3HP difference. The cost to produce equal length headers would be a few hundred dollars more, about $1800 for the equal length headers. They are going to be made of mild steel, with a ceramic outside coating and thermobaric inside coating. Hopefully with the lower price, people might be more interested. I'm still going to get a set for myself.
![Smilie](https://mbworld.org/forums/images/smilies/smile.gif)
Oh yeah, the primary tube diameter will be 1.75 inches in diameter. The primary tubes on the Evosport shorty headers are 1.625 inches in diameter. Larger primary tubes are better for FI motors.
For more info or to get a group buy together, you can contact me or Josh R. I will try and keep this project updated continually.
Regarding an ECU retune, I'm not sure about that, but I can ask.
Last edited by pshek; 01-31-2006 at 01:33 AM.
#70
Super Member
Join Date: Jun 2003
Location: bay area, california
Posts: 714
Likes: 0
Received 0 Likes
on
0 Posts
'14 428i M-Sport, '02 C32 AMG
Originally Posted by pshek
Update:
The header design was revised after talking with Josh R. They are going to be unequal length shorty headers. Everything else has remained unchanged, except the cost. They will cost $1150. Josh said that the equal length headers would provide only a marginally higher HP gain than the unequal length, about 3HP difference. The cost to produce equal length headers would be a few hundred dollars more, about $1800 for the equal length headers. They are going to be made of mild steel, with a ceramic outside coating and thermobaric inside coating. Hopefully with the lower price, people might be more interested. I'm still going to get a set for myself.![Smilie](https://mbworld.org/forums/images/smilies/smile.gif)
Oh yeah, the primary tube diameter will be 1.75 inches in diameter. The primary tubes on the Evosport shorty headers are 1.625 inches in diameter. Larger primary tubes are better for FI motors.
For more info or to get a group buy together, you can contact me or Josh R. I will try and keep this project updated continually.
Regarding an ECU retune, I'm not sure about that, but I can ask.
The header design was revised after talking with Josh R. They are going to be unequal length shorty headers. Everything else has remained unchanged, except the cost. They will cost $1150. Josh said that the equal length headers would provide only a marginally higher HP gain than the unequal length, about 3HP difference. The cost to produce equal length headers would be a few hundred dollars more, about $1800 for the equal length headers. They are going to be made of mild steel, with a ceramic outside coating and thermobaric inside coating. Hopefully with the lower price, people might be more interested. I'm still going to get a set for myself.
![Smilie](https://mbworld.org/forums/images/smilies/smile.gif)
Oh yeah, the primary tube diameter will be 1.75 inches in diameter. The primary tubes on the Evosport shorty headers are 1.625 inches in diameter. Larger primary tubes are better for FI motors.
For more info or to get a group buy together, you can contact me or Josh R. I will try and keep this project updated continually.
Regarding an ECU retune, I'm not sure about that, but I can ask.
#71
MBWorld Fanatic!
Join Date: Jul 2004
Location: Diamond Bar & Anaheim, CA
Posts: 1,194
Likes: 0
Received 2 Likes
on
2 Posts
2003 C-Class Sportcoupe
Sorry, they are going to be made of mild steel. Stainless steel costs a lot more than coated mild steel. I was going to buy Supersprint's stainless steel headers, until I found out they were going to cost me $2200.
These headers will be a good price without sacrificing quality.
I guess pictures and dyno results speak for themselves, so I'll stop rambling and post results when they're ready.
These headers will be a good price without sacrificing quality.
I guess pictures and dyno results speak for themselves, so I'll stop rambling and post results when they're ready.
Last edited by pshek; 01-31-2006 at 01:57 AM.
#72
Newbie
Join Date: Jun 2005
Location: Southern California
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
2003 Desert Silver C32
How are these headers dealt with when it comes to smogging the car later in California I keep seeing the question are they CARB certified, what's this?
#74
MBWorld Fanatic!
Join Date: Jul 2004
Location: Diamond Bar & Anaheim, CA
Posts: 1,194
Likes: 0
Received 2 Likes
on
2 Posts
2003 C-Class Sportcoupe
I haven't had the engine swapped yet, hopefully next week. Josh R told me it should be making over 400rwhp after the port and polish work on the cylinder heads and supercharger, also schrick cams too. The engine is basically ready to be put back together now for the swap.
#75
MBWorld Fanatic!
Join Date: Jul 2004
Location: Diamond Bar & Anaheim, CA
Posts: 1,194
Likes: 0
Received 2 Likes
on
2 Posts
2003 C-Class Sportcoupe
Originally Posted by benzoAMGpower
pshek... make anymore power after the port and flow???
Originally Posted by pshek
I haven't had the engine swapped yet, hopefully next week. Josh R told me it should be making over 400rwhp after the port and polish work on the cylinder heads and supercharger, also schrick cams too. The engine is basically ready to be put back together now for the swap.
![tard](https://mbworld.org/forums/images/smilies/tard.gif)
Originally Posted by c32suarez
How are these headers dealt with when it comes to smogging the car later in California I keep seeing the question are they CARB certified, what's this?
![Smilie](https://mbworld.org/forums/images/smilies/smile.gif)