I think they're ready...
Thread Starter
MBWorld Fanatic!
Joined: Mar 2009
Posts: 2,136
Likes: 6
From: GA
2016 Chevrolet SS, 2006 Cadillac STS-V
I think they're ready...
I think I have my BiX ready to install! I took them apart and had the shrouds painted to match my car and I reattached the broken tabs. The seller had reattached the tabs with "super glue" so I knew I was going to have to reinforce that. One of the top tabs broke off again in shipping. I used a 2 part epoxy called plastic weld and I scuffed up the areas with a die grinder so it had something to grab onto and then just layed it on thick. I didn't bother removing the other tabs that were still glued on. For now it seems very strong. I can yank on the tab pretty good and it doesn't show any sign of coming off, but I just don't know if it'll hold up to the temperature changes and such. 
Hopefully I'll be installing them Saturday. Here's a few teaser pictures and of the tabs on one of them:
Hopefully I'll be installing them Saturday. Here's a few teaser pictures and of the tabs on one of them:
Thread Starter
MBWorld Fanatic!
Joined: Mar 2009
Posts: 2,136
Likes: 6
From: GA
2016 Chevrolet SS, 2006 Cadillac STS-V
Its not that hard to get them open, I just used a heat gun and a scraper to pry them open without any damage. When I went back together I put a small amout of gray engine sealant (RTV) to make sure they're sealed well, and then used the heat gun and some pliers to carefully squeeze the lens back on. Took much longer to get the lens back in that it did to get it off.
Super Member
Joined: Aug 2009
Posts: 983
Likes: 2
From: USA
Marsaydees
you're supposed to use a special gum to seal the headlights.
you can get it cheaper at the nissan dealership. they call it some sort of headlight glue. you lay it out on the headlight, then heat it up, then mush the lens into it and when it cools down it creates an airtight seal
you can get it cheaper at the nissan dealership. they call it some sort of headlight glue. you lay it out on the headlight, then heat it up, then mush the lens into it and when it cools down it creates an airtight seal
Thread Starter
MBWorld Fanatic!
Joined: Mar 2009
Posts: 2,136
Likes: 6
From: GA
2016 Chevrolet SS, 2006 Cadillac STS-V
I was going to get the Nissan stuff, but there was enough left in the headlight that I'm sure the little bit ofsETV I put in there will seal it up fine. I probably could have gotten away without the RTV actually.
Trending Topics
Thread Starter
MBWorld Fanatic!
Joined: Mar 2009
Posts: 2,136
Likes: 6
From: GA
2016 Chevrolet SS, 2006 Cadillac STS-V
MB World Stories
The Best of Mercedes & AMG
Manual Mercedes? 6 Times Sindelfingen Let Drivers Have All The Fun
Verdad Gallardo
Mercedes SLR McLaren 722 S Is Extremely Rare Example Modified by McLaren
Verdad Gallardo
8 Classic Boxy Mercedes Designs That Have Aged Like Fine Wine
Verdad Gallardo
Flawlessly Restored Mercedes 190E Evo II Heads to Auction
Verdad Gallardo
Electric Mercedes C-Class Unveiled: 11 Things You Need to Know
Verdad Gallardo
Mercedes EQS Gets A Major Update: Everything You Need to Know
Verdad Gallardo
5 Underrated Mercedes-Benz Models That Don't Get the Love They Deserve
Verdad Gallardo
Mercedes 300D Has Pushed Well Past 1 Million Miles and It Ain't Stopping
Verdad Gallardo
10 Most Reliable Mercedes-Benz Models You Can Buy Used
Verdad Gallardo
Member
Joined: Jan 2007
Posts: 111
Likes: 1
From: Houston Area
09 GL 550, 08 BMW X5 4.8, 05 C55 AMG, 05 GSX-R1000 (sold), Denali XL (sold)
Senior Member
Joined: Aug 2008
Posts: 473
Likes: 0
From: Tampa, Florida
2005 c55amg, 2000 clk430, 2002 clk55amg, 2008 clk63amg black series
I think I have my BiX ready to install! I took them apart and had the shrouds painted to match my car and I reattached the broken tabs. The seller had reattached the tabs with "super glue" so I knew I was going to have to reinforce that. One of the top tabs broke off again in shipping. I used a 2 part epoxy called plastic weld and I scuffed up the areas with a die grinder so it had something to grab onto and then just layed it on thick. I didn't bother removing the other tabs that were still glued on. For now it seems very strong. I can yank on the tab pretty good and it doesn't show any sign of coming off, but I just don't know if it'll hold up to the temperature changes and such. Hopefully I'll be installing them Saturday. Here's a few teaser pictures and of the tabs on one of them:
Hopefully I'll be installing them Saturday. Here's a few teaser pictures and of the tabs on one of them:It looks good.....i just paid my guy to do it cause he has done them before...
