Fog Lamp Pigtails/Connectors?
#1
Thread Starter
Member
Joined: Jan 2017
Posts: 146
Likes: 5
From: Calgary, Alberta, Canada
2003 Corvette Z06, 1999 E55 AMG
Fog Lamp Pigtails/Connectors?
Hey guys,
So the guy I bought the car from installed these awful fog lamps. I purchased the oem lamps on pelican parts and I just received them and now I'm trying to install. Only problem is it was a hack job with wires, etc and the new fogs didn't come with a pigtail or connector to connect the new ones.
here is a picture. Anyone know where I can get this or what it's even called?
thanks again as always for everyones help.
So the guy I bought the car from installed these awful fog lamps. I purchased the oem lamps on pelican parts and I just received them and now I'm trying to install. Only problem is it was a hack job with wires, etc and the new fogs didn't come with a pigtail or connector to connect the new ones.
here is a picture. Anyone know where I can get this or what it's even called?
thanks again as always for everyones help.
#3
Thread Starter
Member
Joined: Jan 2017
Posts: 146
Likes: 5
From: Calgary, Alberta, Canada
2003 Corvette Z06, 1999 E55 AMG
Yes that is it. What is it called so I can order two of them?
Also where would be the cheapest place by not going to the dealership?
thanks Zayed.
Also where would be the cheapest place by not going to the dealership?
thanks Zayed.
#5
MBWorld Fanatic!
Joined: Aug 2006
Posts: 7,034
Likes: 385
From: A.D., U.A.E
00 C200 & 00 C55 & 06 SLK55
Sure bro.,
can get it from "Ebay or ECS tuning", part #: "202 440 03 07":-
http://www.ebay.com/itm/MERCEDES-W20...1W6BKN&vxp=mtr
https://www.ecstuning.com/b-genuine-...es/2024400307/
;ZAEYD;
can get it from "Ebay or ECS tuning", part #: "202 440 03 07":-
http://www.ebay.com/itm/MERCEDES-W20...1W6BKN&vxp=mtr
https://www.ecstuning.com/b-genuine-...es/2024400307/
;ZAEYD;
The following users liked this post:
edhu (03-24-2023)
#10
Thank you I have tried.. everything from a s class e-class. I even try the clk. I might be looking at the wrong years. If you have any suggestions please share with the group. Thank you
The following users liked this post:
mrmatthewpaul (03-09-2023)
#12
MBWorld Fanatic!
Joined: Mar 2005
Posts: 2,369
Likes: 180
From: America
1999 C43 AMG, 2005 E55 Wagon
#14
That would be great. Please message me on what you find out. Thank you.
To all w202 C43 owners. If we get this harness. I would like to reach out to am manufacturer and see how much( money) would it take to make this harness. I looked this up before and I found Someone once who put on their website that basically read anything is possible the only thing is 50 pieces would have to be ordered.
The second possible solution is to reach out to a 3D printing company and see if they can help. I don't mind do either.. option. Option one is was very expensive. It was 50 thousand then I am not sure if it is more or the same. If we go this route the lot ordered would have to be divided according to how much a person put in. This option would be challenging for my point of view.
Option 2 seems easier. I am not sure if it would be possible but thinking about it being able to be printed on demand just see cheaper and one the fill is made we ( the C43 community) will have that fill forever and they can pay to have their own part made as need.
Does anyone have any thoughts or knowledge about 3D printing or manufacturer ?
the piece that would be made is the connector portion not the hole harness. Any wire and heat shrink can be used to make your own pig tail.
sorry if this is hard to understand. I am writing this on me phone and I can see the whole paragraph or sentence. Thank you everyone who replies to this message.
To all w202 C43 owners. If we get this harness. I would like to reach out to am manufacturer and see how much( money) would it take to make this harness. I looked this up before and I found Someone once who put on their website that basically read anything is possible the only thing is 50 pieces would have to be ordered.
The second possible solution is to reach out to a 3D printing company and see if they can help. I don't mind do either.. option. Option one is was very expensive. It was 50 thousand then I am not sure if it is more or the same. If we go this route the lot ordered would have to be divided according to how much a person put in. This option would be challenging for my point of view.
Option 2 seems easier. I am not sure if it would be possible but thinking about it being able to be printed on demand just see cheaper and one the fill is made we ( the C43 community) will have that fill forever and they can pay to have their own part made as need.
Does anyone have any thoughts or knowledge about 3D printing or manufacturer ?
the piece that would be made is the connector portion not the hole harness. Any wire and heat shrink can be used to make your own pig tail.
sorry if this is hard to understand. I am writing this on me phone and I can see the whole paragraph or sentence. Thank you everyone who replies to this message.
#15
You can still order or find a third brake light. As for the steering wheel you can always have it refurbished unless someone broke it. If that is the case I would go to a junk yard/ pick and pull and get another to have it refurbished to the way you like it( color and type of leather)
The following users liked this post:
mrmatthewpaul (03-09-2023)
The following users liked this post:
mrmatthewpaul (03-09-2023)