2008-ML350:P0019-Crankshaft Position-Camshaft Position Correlation (Bank 2 Sensor B)
Thread Starter
Member
Joined: Mar 2011
Posts: 78
Likes: 2
From: NJ
2008 ML320 (W164) - 201K Miles
2008-ML350:P0019-Crankshaft Position-Camshaft Position Correlation (Bank 2 Sensor B)
Hi,
I am getting below code in my 2008 ML350
P0019 - Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)
Can anyone please help me what could be problem and how do I go about solving this problem.
Is this Crank Shaft Position Sensor bad ? on Bank 2 ?
If yes, what is the location of this sensor or my car ? It seems simple to change if I know the location of this sensor.
Thanks in Advance on any help or hint
I am getting below code in my 2008 ML350
P0019 - Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)
Can anyone please help me what could be problem and how do I go about solving this problem.
Is this Crank Shaft Position Sensor bad ? on Bank 2 ?
If yes, what is the location of this sensor or my car ? It seems simple to change if I know the location of this sensor.
Thanks in Advance on any help or hint
Newbie
Joined: Jan 2012
Posts: 3
Likes: 0
ML430 (former), ML500 (former), CLS550 (former), ML350 (current)
bank b is on the drivers side. mine is an '06, maybe yours will be in the same place, they are located just under the air intake hose on the drivers side, attached to the front top of motor.
***there are some videos on youtube as to replacing.
most likely it's the sensor. you can get them on Ebay much cheaper than from the dealer.
***there are some videos on youtube as to replacing.
most likely it's the sensor. you can get them on Ebay much cheaper than from the dealer.
Last edited by shercrawford; Oct 18, 2014 at 10:42 PM. Reason: more info
Thread Starter
Member
Joined: Mar 2011
Posts: 78
Likes: 2
From: NJ
2008 ML320 (W164) - 201K Miles
I tried to locate CPS sensor on driver side but I am not able to locate CPS. I tried to look at every possible place but I am not able to find anywhere. Even I tried on back of engine towards firewall where I could not see but try to feel with touch but still no luck. Unless it is hidden somewhere or I am looking at incorrect place I do not seem to find CPS sensor.
I looked at Youtube video for CPS center replacement but none of them matching with W164 engine.
I have attached top view of engine on driver side after removing engine cover and Air Hose. I would really appreciate if someone can give me hint on where CPS sensor could be on driver side.
I looked at Youtube video for CPS center replacement but none of them matching with W164 engine.
I have attached top view of engine on driver side after removing engine cover and Air Hose. I would really appreciate if someone can give me hint on where CPS sensor could be on driver side.
Thread Starter
Member
Joined: Mar 2011
Posts: 78
Likes: 2
From: NJ
2008 ML320 (W164) - 201K Miles
Anyone can help me with P0019 code ?. Car runs fine no issue. Just to give you some background my car had oil sludge when I got this code. I flushed oil twice before final oil. P0019 suppose to be for CPS but I really doubt it if that is the case.
Please please help
Please please help
Thread Starter
Member
Joined: Mar 2011
Posts: 78
Likes: 2
From: NJ
2008 ML320 (W164) - 201K Miles
Finally I was able to replace Crankshaft Position Sensor located on driver side of firewall. You cannot see it but if you put your hand, you will able to feel and it replace it from top of engine. I had to remove Air Filter box to get to area behind it. Still P0019 issue not resolved. Engine Light came back after replacement. Obviously solution is something else t P0019. Car runs great for one year with this issue but bothering Check Engine Light. Anyone has clue what else could be the issue ?
Thread Starter
Member
Joined: Mar 2011
Posts: 78
Likes: 2
From: NJ
2008 ML320 (W164) - 201K Miles
I am still getting P0019 obd2 code and car is running very rough. I did change Crank Shaft Sensor but still same issue. P0019 is error code for Bank 2 Sensor B. I know Bank 2 is on driver side but anyone can tell me which one is Sensor B on Driver side out of two Camshaft Sensor ?
Trending Topics
Thread Starter
Member
Joined: Mar 2011
Posts: 78
Likes: 2
From: NJ
2008 ML320 (W164) - 201K Miles
If anyone is looking for P0016/P0017/P0018/P0019 OBD2 Error code location of Camshaft Sensor and specific location of given code, please see attached Diagram. P0016/P0017/P0018 Sensor is very easy less than 10 min. job to change but P0019 is 1 to 2 hour job to change. P0019 sensor is located behind Power Steering Reservoir and you have to remove PS Reservoir to replace this sensor. There is lots of write up on how to replace PS Reservoir. Hardest part I found was to put back C-Clip behind PS, in fact I dropped and lost two C-Clips during this process.
Last edited by lordofthering; Jul 20, 2015 at 11:17 AM. Reason: adding image
MB World Stories
The Best of Mercedes & AMG
Manual Mercedes? 6 Times Sindelfingen Let Drivers Have All The Fun
Verdad Gallardo
Mercedes SLR McLaren 722 S Is Extremely Rare Example Modified by McLaren
Verdad Gallardo
8 Classic Boxy Mercedes Designs That Have Aged Like Fine Wine
Verdad Gallardo
Flawlessly Restored Mercedes 190E Evo II Heads to Auction
Verdad Gallardo
Electric Mercedes C-Class Unveiled: 11 Things You Need to Know
Verdad Gallardo
Mercedes EQS Gets A Major Update: Everything You Need to Know
Verdad Gallardo
5 Underrated Mercedes-Benz Models That Don't Get the Love They Deserve
Verdad Gallardo
Mercedes 300D Has Pushed Well Past 1 Million Miles and It Ain't Stopping
Verdad Gallardo
10 Most Reliable Mercedes-Benz Models You Can Buy Used
Verdad Gallardo
Thread Starter
Member
Joined: Mar 2011
Posts: 78
Likes: 2
From: NJ
2008 ML320 (W164) - 201K Miles
Still I do not know. Still runs rough sometimes and sometimes it is ok. My P0019 code has not gone yet. I am planning to take it to MB Tech since I have given up on this code. May be timing is off if that is the case, I am looking at couple thousands expense.
Senior Member
Joined: Mar 2014
Posts: 286
Likes: 19
e320
sorry the sensor you replaced did not fix it
i know nothing about this engine
but i appreciate you keeping the thread up to date, it is nice when people posts the process and the solutions like you are
will be interested to hear what the mb mechanic finds is wrong
good luck, hope it is not expensive
i know nothing about this engine
but i appreciate you keeping the thread up to date, it is nice when people posts the process and the solutions like you are
will be interested to hear what the mb mechanic finds is wrong
good luck, hope it is not expensive
Newbie
Joined: Jun 2015
Posts: 2
Likes: 0
2007 ML 350
Hi -
Daughters 2007 ml350 has the code P0018. From what I see here it is one of the easier ones to replace - can someone point out a part # of what I need to buy to replace and fix this error code? I know its on the drivers side. And there is a pic posted here but it doesn't open and is too small to make out.
thanks in advance.
Daughters 2007 ml350 has the code P0018. From what I see here it is one of the easier ones to replace - can someone point out a part # of what I need to buy to replace and fix this error code? I know its on the drivers side. And there is a pic posted here but it doesn't open and is too small to make out.
thanks in advance.
Junior Member
Joined: Apr 2014
Posts: 19
Likes: 0
From: Southern California
S550
MBWorld Fanatic!
Joined: Oct 2011
Posts: 7,107
Likes: 765
From: Bronx, N.Y.
2002 ML 320 & 2006 ML500
Newbie
Joined: Jan 2009
Posts: 2
Likes: 0
ML 350 06
the control valve is located behind the sensor and it's left hand threaded also you need to counter hold a nut on the back side of the engine (towards the firewall)
Last edited by umea; Aug 23, 2017 at 12:20 AM.
Junior Member
Joined: Apr 2012
Posts: 21
Likes: 1
S550
MBWorld Fanatic!
Joined: Oct 2011
Posts: 7,107
Likes: 765
From: Bronx, N.Y.
2002 ML 320 & 2006 ML500
https://mbworld.org/forums/s-class-w221-74/
Newbie
Joined: Jul 2019
Posts: 6
Likes: 0
From: Florida
ML350-300E-SLK230
WOW the camshaft valve was the problem. Here in USA we have the same problem but bank A (passenger side) and the problem is the Balance Shaft according with mechanics. To fix it cost too much money. The engine has to be removed from the car to remove the balance shaft and remove the adjuster. About $2000 dollars job.
I will try to change the camshaft valve first to see if the light goes off. My car drives very well and I replaced the parts you indicated before but the light goes ON again.
In youtube there is a video about it. Many ML350 have had that problem here in USA. Lucky you that the problem was the camshaft exhausted control valve only. Julio
I will try to change the camshaft valve first to see if the light goes off. My car drives very well and I replaced the parts you indicated before but the light goes ON again.
In youtube there is a video about it. Many ML350 have had that problem here in USA. Lucky you that the problem was the camshaft exhausted control valve only. Julio
