Want airmatic to lower car faster
#1
Junior Member
Thread Starter
Want airmatic to lower car faster
Have a 2000 s500 is there a way to make the car drop faster and more audiable I like when you can here air ride cars drop
#2
Super Member
#3
https://mbworld.org/forums/s-class-w220/575597-kangairoo-adjust-ride-height-your-smartphone.html
its a Manual control for the suspension
#4
Junior Member
Thread Starter
No we’re to be found
I just tried to contact him and it says that he’s banned....Is it possible to do lowering links and washers to get the car to full drop to the floor when parked. Then I wanna be able to raise it up to drive
#5
MBWorld Fanatic!
No, if you do links/washers, it will be at the set height all the time. Need to go aftermarket to slam it and raise it on command.
The factory system doesn't have an air tank, it relies on the compressor 100% of the time. If you constantly slam and raise the car, you will probably burn up stock compressors in record time, they just arent' designed for that.
The factory system doesn't have an air tank, it relies on the compressor 100% of the time. If you constantly slam and raise the car, you will probably burn up stock compressors in record time, they just arent' designed for that.
#6
Junior Member
Thread Starter
No, if you do links/washers, it will be at the set height all the time. Need to go aftermarket to slam it and raise it on command.
The factory system doesn't have an air tank, it relies on the compressor 100% of the time. If you constantly slam and raise the car, you will probably burn up stock compressors in record time, they just arent' designed for that.
The factory system doesn't have an air tank, it relies on the compressor 100% of the time. If you constantly slam and raise the car, you will probably burn up stock compressors in record time, they just arent' designed for that.
#7
MBWorld Fanatic!
Yeah you can raise and lower it as normal, but it will not be fast or any lower than you set the base setting to.
In theory, you could put a release valve on the lines, and trigger it when parked to slam the car, then let it pump back up when you start it back up.
In theory, you could put a release valve on the lines, and trigger it when parked to slam the car, then let it pump back up when you start it back up.
Trending Topics
#8
yes this would be the easiest solution , set up 4 switches to open each of the 4 air lines and you'll drop the car to the ground . It will be one way only (you'll be able to drop the car fast , but refill will be slow using the oem compressor )
#9
Junior Member
Thread Starter
Programa
I was reading about the programa lowering module and it said if you have active dampening it only drop your car 1 inch lower than the lowest setting so to get the car any lower I would still have to put links on the car so wouldn’t I just be better off just doing links alone and drive with the raised or will it Not be raised enough ?
#10
MBWorld Fanatic!
I think you need to research how the system actually works more.
The links set the level the car always aims for. Raising it with the button lifts it about an inch, and once you go over a certain speed it drops back down. Not enough to slam it normally, then drive it raised without problems.
The links set the level the car always aims for. Raising it with the button lifts it about an inch, and once you go over a certain speed it drops back down. Not enough to slam it normally, then drive it raised without problems.
#13
The following users liked this post:
Justin Cruz (05-18-2021)
#15
Wow that's awesome ! Can you lift just the rear , or just the front , by manual control ?
or does it raise and lower all 4 corners at the same time ?
or does it raise and lower all 4 corners at the same time ?
Last edited by tusabes; 02-27-2018 at 04:17 PM.
#17
Senior Member
To answer your orignal question, yes, your can bypass the pressure release valve for the entire system. The pressure release valve is part of the airmatic pump, it is prone to leaking on high mileage cars. Also, the valve gets stuck overtime and fails. I have replaced my airmatic pump twice, the last pump the pressure release valve failed, I bypassed it before getting a new pump.
If you search for my other posts, you can find the push fit fittings I use and my hack to allow me to manually adjust the ride height.
Retro fit pressure release valve to Airmatic pump.
- All airmaic poly air lines are 4mm in diameter. 5/32" fitting work with 4mm tubing.
- You need to put a TEE fitting in between the pump and valve block
- I used a 12v solenoid air valve commonly used in aftermarket air suspension systems. You don't need the huge 3/8" or even 1/4" openings since you need to reduce down to 5/32" anyways. I had a valve that used 1/8" fittings
- I TEE;d into the output of the pump and then connected to the input of the new dump valve.
- For the electrical connection, you need to disconnect the connecter from the pump and then you can use 2.8 mm female spade connectors to hook into the orignal connector. I tired to just put my valve in parallel with the orignal valve on the pump, but my valve was shorted and having both connected would not activate my new valve.
- In my picture, I have the output of the new dump valve directed vented. This makes a huge amount of noise, it will give you the "woosh"noise when the airmatic is venting. This proved to be too loud for me, so I put an air muffler on the output. I also used a large tubing tee and vented it back into the stock air muffler, both solustions work.
If you search for my other posts, you can find the push fit fittings I use and my hack to allow me to manually adjust the ride height.
Retro fit pressure release valve to Airmatic pump.
#19
Senior Member
#20
Member
To answer your orignal question, yes, your can bypass the pressure release valve for the entire system. The pressure release valve is part of the airmatic pump, it is prone to leaking on high mileage cars. Also, the valve gets stuck overtime and fails. I have replaced my airmatic pump twice, the last pump the pressure release valve failed, I bypassed it before getting a new pump.
If you search for my other posts, you can find the push fit fittings I use and my hack to allow me to manually adjust the ride height.
Retro fit pressure release valve to Airmatic pump.
- All airmaic poly air lines are 4mm in diameter. 5/32" fitting work with 4mm tubing.
- You need to put a TEE fitting in between the pump and valve block
- I used a 12v solenoid air valve commonly used in aftermarket air suspension systems. You don't need the huge 3/8" or even 1/4" openings since you need to reduce down to 5/32" anyways. I had a valve that used 1/8" fittings
- I TEE;d into the output of the pump and then connected to the input of the new dump valve.
- For the electrical connection, you need to disconnect the connecter from the pump and then you can use 2.8 mm female spade connectors to hook into the orignal connector. I tired to just put my valve in parallel with the orignal valve on the pump, but my valve was shorted and having both connected would not activate my new valve.
- In my picture, I have the output of the new dump valve directed vented. This makes a huge amount of noise, it will give you the "woosh"noise when the airmatic is venting. This proved to be too loud for me, so I put an air muffler on the output. I also used a large tubing tee and vented it back into the stock air muffler, both solustions work.
If you search for my other posts, you can find the push fit fittings I use and my hack to allow me to manually adjust the ride height.
Retro fit pressure release valve to Airmatic pump.
Last edited by takeiteasy; 05-24-2019 at 02:13 PM.
#21
Senior Member
The one I used was a surplus item I had in my junk box. There are a lot with 1/2" ports, this maybe over kill for the airmatic dump valve since the air lines a so small.
#22
#23
Senior Member
Recently sold my w220.... My setup was 100 % diy homemade. Links were made from metal geared rc servos that were part of the links that could be made longer or shorter at a turn of a knob.
#24
That’s cool! I’ll try to replicate your links and make some myself. Also how did you get access to the cabin from the engine bay? I’m trying to get the wires for the remote from programa to the inside of the cabin