*** VRP 82mm TB ***
#53
Banned
Thread Starter
Join Date: May 2004
Location: Richmond Hill, Ontario
Posts: 3,797
Likes: 0
Received 2 Likes
on
2 Posts
2003 E55 AMG
Sorry for the delays guys.. I've got a large order pending for these 82mm bodies. I just need to plug them into a few more cars and make sure all the electronics work properly.. Since I dont have an inlet to bolt it to I cannot fully install it and test it on the road.
As long as the electronics check out and the throttle plate moves as expected then I know that everything will be fine when they are installed..
I will make the bodies available once I've had a chance to verify all of this.
As long as the electronics check out and the throttle plate moves as expected then I know that everything will be fine when they are installed..
I will make the bodies available once I've had a chance to verify all of this.
#56
MBWorld Fanatic!
Join Date: Feb 2004
Location: Southern, CA.
Posts: 9,155
Likes: 0
Received 19 Likes
on
18 Posts
V12-Biturbo
Was poking around the-Bay found a perfect stocker
Maybe good for some experiments
http://cgi.ebay.com/ebaymotors/Merce...Q5fAccessories
http://cgi.ebay.com/ebaymotors/Merce...Q5fAccessories
#58
MBWorld Fanatic!
Join Date: Nov 2007
Location: Daytona, Florida
Posts: 1,517
Likes: 0
Received 9 Likes
on
6 Posts
SL600
Maybe good for some experiments
http://cgi.ebay.com/ebaymotors/Merce...Q5fAccessories
http://cgi.ebay.com/ebaymotors/Merce...Q5fAccessories
#59
MBWorld Fanatic!
Maybe good for some experiments
http://cgi.ebay.com/ebaymotors/Merce...Q5fAccessories
http://cgi.ebay.com/ebaymotors/Merce...Q5fAccessories
#62
Member
the throttle body that is 82mm is a 273 engine throttle body and yes the eletronics do work!!! i have it on my 2006 cls55 renntech stage 5 plus 650hp!!!
#65
MBWorld Fanatic!
Join Date: Nov 2007
Location: Daytona, Florida
Posts: 1,517
Likes: 0
Received 9 Likes
on
6 Posts
SL600
If the M275 is the same design Benz usually uses for their V12's, and like the setup that came with my M120, then you probably have two completely separate 72mm or 74mm TB's, one feeding each cylinder bank. Pretty advanced design.
If that's the case, then the bottom line for your motor is that there's probably no worthwhile gains to be had with larger TB's. Because you have 148mm of total capacity already, your motor would probably need to be pushing 800+hp before that would ever become a real constriction point.
I'm sure there might be some very slight gains to be had with larger TB's, or with a port and polish job, like a couple rwhp maybe. But you'll never see that huge 60hp bump that the 55k guys will, with their 500hp+ motors sucking through a single 72mm-80mm TB, because your motor doesn't have that capacity constraint at the TB in the first place.
If you can verify that your motor does have the twin TB's, then I would skip this mod, it's never going to give you a real bang for the buck.
If that's the case, then the bottom line for your motor is that there's probably no worthwhile gains to be had with larger TB's. Because you have 148mm of total capacity already, your motor would probably need to be pushing 800+hp before that would ever become a real constriction point.
I'm sure there might be some very slight gains to be had with larger TB's, or with a port and polish job, like a couple rwhp maybe. But you'll never see that huge 60hp bump that the 55k guys will, with their 500hp+ motors sucking through a single 72mm-80mm TB, because your motor doesn't have that capacity constraint at the TB in the first place.
If you can verify that your motor does have the twin TB's, then I would skip this mod, it's never going to give you a real bang for the buck.
#66
MBWorld Fanatic!
Join Date: Feb 2004
Location: Southern, CA.
Posts: 9,155
Likes: 0
Received 19 Likes
on
18 Posts
V12-Biturbo
If the M275 is the same design Benz usually uses for their V12's, and like the setup that came with my M120, then you probably have two completely separate 72mm or 74mm TB's, one feeding each cylinder bank. Pretty advanced design.
If that's the case, then the bottom line for your motor is that there's probably no worthwhile gains to be had with larger TB's. Because you have 148mm of total capacity already, your motor would probably need to be pushing 800+hp before that would ever become a real constriction point.
I'm sure there might be some very slight gains to be had with larger TB's, or with a port and polish job, like a couple rwhp maybe. But you'll never see that huge 60hp bump that the 55k guys will, with their 500hp+ motors sucking through a single 72mm-80mm TB, because your motor doesn't have that capacity constraint at the TB in the first place.
If you can verify that your motor does have the twin TB's, then I would skip this mod, it's never going to give you a real bang for the buck.
If that's the case, then the bottom line for your motor is that there's probably no worthwhile gains to be had with larger TB's. Because you have 148mm of total capacity already, your motor would probably need to be pushing 800+hp before that would ever become a real constriction point.
I'm sure there might be some very slight gains to be had with larger TB's, or with a port and polish job, like a couple rwhp maybe. But you'll never see that huge 60hp bump that the 55k guys will, with their 500hp+ motors sucking through a single 72mm-80mm TB, because your motor doesn't have that capacity constraint at the TB in the first place.
If you can verify that your motor does have the twin TB's, then I would skip this mod, it's never going to give you a real bang for the buck.
Thought someone might want it..
Last edited by Thericker; 03-15-2009 at 03:20 PM.
#70
Super Member
Join Date: Sep 2008
Location: SoCal
Posts: 504
Likes: 0
Received 0 Likes
on
0 Posts
SL55 AMG