Largest throttle body kit for 55
#76
Junior Member
Join Date: Mar 2013
Location: Portland, OR
Posts: 29
Likes: 0
Received 0 Likes
on
0 Posts
2007 E63 AMG, 2009 ML63 AMG
This might be a stupid question, but would it be possible to mount two TBs on the two intake tubes at the front of the engine where there is more room? That is how my Viper twinscrew SC is setup and it is similar to the basic e55 layout with the exception of the location of the TB.
You would need to mechanically link the two TBs and figure out how to run the TPS off one of them. It doesn't seem like it would be that hard to do but I am also not very familiar with the e55 SC setup.
You would need to mechanically link the two TBs and figure out how to run the TPS off one of them. It doesn't seem like it would be that hard to do but I am also not very familiar with the e55 SC setup.
#77
Junior Member
Join Date: Mar 2013
Location: Portland, OR
Posts: 29
Likes: 0
Received 0 Likes
on
0 Posts
2007 E63 AMG, 2009 ML63 AMG
Actually, now that I take a closer look, the TBs would be difficult to link together on the e55 due to the wide spacing that the intake pipes must follow.
#78
Super Member
Join Date: Mar 2011
Location: Porter Ranch, CA
Posts: 502
Likes: 0
Received 0 Likes
on
0 Posts
E55, CTS-V Wagon, Duc 1098R
My 82 was actually ported by maxbore and measured 85mm and I also did the shaft grind so that could have played a part. The 90 had no work done to it. No CEL's and I did do the rpm increase thru star and also reinitialized the adaptations as well so that it could properly calibrate. The good part of the 90 is that it holds the peak power longer since before it my peak would drop off at around 5800rpm but with the 90 it now happens at 6300.
#79
Super Member
Join Date: Mar 2011
Location: Porter Ranch, CA
Posts: 502
Likes: 0
Received 0 Likes
on
0 Posts
E55, CTS-V Wagon, Duc 1098R
I mocked it up so it can fit. Problem is getting it to idle which will be next to impossible. You don't need more than a 90 with the stock blower anyway. It will run out of air before the TB does.
#81
MBWorld Fanatic!
Join Date: Aug 2006
Location: A.D., U.A.E
Posts: 7,033
Likes: 0
Received 384 Likes
on
349 Posts
00 C200 & 00 C55 & 06 SLK55
![thumbs](https://mbworld.org/forums/images/smilies/thumbsup.gif)
where can we get the 90mm connector plug from....?,
and do you use some kind of adapter or spacer then welding it to the snout....??
ZAYED,,
#83
Super Member
Join Date: Mar 2011
Location: Porter Ranch, CA
Posts: 502
Likes: 0
Received 0 Likes
on
0 Posts
E55, CTS-V Wagon, Duc 1098R
The 90 is nothing like the 82 conversion and requires basically 1.5-2" worth of the inlet to be refabricated. The 90 is so big that it is actually larger than the MB casting. You can see it in the pictures that I posted earlier in the thread. The connectors can be purchased from a dodge and mercedes dealership and need to be soldered together. It is not a plug and play situation like the 82 but obviously not impossible either. As mentioned, you will need a custom Y-pipe as well.
One thing to note, is that in order to get these gains, you have to be "choking" the 82mm. I believe Forrest is running a 180mm crank with the smaller upper pulley which would be equivalent to a 195mm. You shouldn't expect to achieve similar results with just a 180mm or smaller pulley since its likely that the 82 tb is enough.
One thing to note, is that in order to get these gains, you have to be "choking" the 82mm. I believe Forrest is running a 180mm crank with the smaller upper pulley which would be equivalent to a 195mm. You shouldn't expect to achieve similar results with just a 180mm or smaller pulley since its likely that the 82 tb is enough.
#87
MBWorld Fanatic!
There are many types of a T/B connectors, which one for a BBK T/Bs......??
Attachment 258008
Attachment 258009
Attachment 258010
Attachment 258011
Attachment 258012
ZAYED,,
Attachment 258008
Attachment 258009
Attachment 258010
Attachment 258011
Attachment 258012
ZAYED,,
#89
MBWorld Fanatic!
#90
MBWorld Fanatic!
Join Date: Aug 2006
Location: A.D., U.A.E
Posts: 7,033
Likes: 0
Received 384 Likes
on
349 Posts
00 C200 & 00 C55 & 06 SLK55
Thanks, i will try that,
we don’t have a people in the dealer here, we only have a green Zombies here....
,
im afraid when i asked them about the connector, they will said; the pharmacy two buildings beside as....![Discus](https://mbworld.org/forums/images/smilies/discus.gif)
ZAYED,,
we don’t have a people in the dealer here, we only have a green Zombies here....
![Scared](https://mbworld.org/forums/images/smilies/scared.gif)
im afraid when i asked them about the connector, they will said; the pharmacy two buildings beside as....
![Discus](https://mbworld.org/forums/images/smilies/discus.gif)
ZAYED,,
Last edited by cm60k; 04-24-2013 at 11:55 AM.
#91
Super Member
Join Date: Mar 2011
Location: Porter Ranch, CA
Posts: 502
Likes: 0
Received 0 Likes
on
0 Posts
E55, CTS-V Wagon, Duc 1098R
If they can't help you, PM me and I will get you sorted. The connector isn't that cheap from MB and Dodge isn't that much better. It will be about $100-$150 when all said and done. Also, if you need an inlet done for the 90, I have a shop that can do it but as Hulk said, its not like an adapter plate and costs some $$$.
#92
MBWorld Fanatic!
Join Date: Aug 2006
Location: A.D., U.A.E
Posts: 7,033
Likes: 0
Received 384 Likes
on
349 Posts
00 C200 & 00 C55 & 06 SLK55
If they can't help you, PM me and I will get you sorted. The connector isn't that cheap from MB and Dodge isn't that much better. It will be about $100-$150 when all said and done. Also, if you need an inlet done for the 90, I have a shop that can do it but as Hulk said, its not like an adapter plate and costs some $$$.
Thankss for your support....
![thumbs](https://mbworld.org/forums/images/smilies/thumbsup.gif)
ZAYED,,