[GunMoto's] '05 Pewter W211 E55 | First PICS
#79
#82
Are you lowered or using spacers and lastly what is clearance like? Could you have gone bigger? If not, why? It obviously looks like it might rub the outer fender. What is the inside clearance like? If you had a slightly different offset could you center the wheel in your clearance spots better?
For the rear sake, im trying to determine what the absolute widest square set of wheel/tire package could fit. With all the torque we make traction is already limited. Maybe with a less offset wheel theres more room to get a big square set using a small spacer in the rear. Just spit balling here.
Thanks for your time with all these questions and im looking forward to full review of your current setup. It looks great.
For the rear sake, im trying to determine what the absolute widest square set of wheel/tire package could fit. With all the torque we make traction is already limited. Maybe with a less offset wheel theres more room to get a big square set using a small spacer in the rear. Just spit balling here.
Thanks for your time with all these questions and im looking forward to full review of your current setup. It looks great.
#85
Are you lowered or using spacers and lastly what is clearance like? Could you have gone bigger? If not, why? It obviously looks like it might rub the outer fender. What is the inside clearance like? If you had a slightly different offset could you center the wheel in your clearance spots better?
For the rear sake, im trying to determine what the absolute widest square set of wheel/tire package could fit. With all the torque we make traction is already limited. Maybe with a less offset wheel theres more room to get a big square set using a small spacer in the rear. Just spit balling here.
Thanks for your time with all these questions and im looking forward to full review of your current setup. It looks great.
For the rear sake, im trying to determine what the absolute widest square set of wheel/tire package could fit. With all the torque we make traction is already limited. Maybe with a less offset wheel theres more room to get a big square set using a small spacer in the rear. Just spit balling here.
Thanks for your time with all these questions and im looking forward to full review of your current setup. It looks great.
Clearance is good up front, even better with the 275/35 compared to the 255/40, I ran previously. The inner fender lip is flattened and only get slight rubbing at full steering lock going into a driveway. A higher offset such as et32 on 9.5" wide can resolve clearance issues if it's a significant concern.
When trying to match the rear (limited traction as you said), I decided 275 was the minimum width to go. If I went custom wheels (dreaming of CCW Classics), then 18x10 et25 is what I was thinking to start with, which is ironically the same size/fitment I'm running on my smaller, compact E46 BMW.
My overall intent is to reduce the understeer on turn-in and although the W211 is not a track car, I think there is (some) room to improve handling even with the performance compromise of the Airmatic. I'm sure a coilover conversion is a night-and-day improvement, however...lol.
The following users liked this post:
kevstaarr (09-03-2020)
#87
F: 19x9.5 et32 255/35-19 (I will be rolling the fenders but maybe I need a couple mm higher offset)
R: 19x10 et35 285/30/19
Thanks for the help! Not too many stanced (yet beefy tires) wagons with specific offsets out there.
Mike
#88
Ok awesome. I am picking up an e55 AMG wagon and I am assuming fender spacing is relatively similar. In your estimation would these represent a pretty flush fitment (considering the wagon and sedan are the same if you can confirm that)...
F: 19x9.5 et32 255/35-19 (I will be rolling the fenders but maybe I need a couple mm higher offset)
R: 19x10 et35 285/30/19
Thanks for the help! Not too many stanced (yet beefy tires) wagons with specific offsets out there.
Mike
F: 19x9.5 et32 255/35-19 (I will be rolling the fenders but maybe I need a couple mm higher offset)
R: 19x10 et35 285/30/19
Thanks for the help! Not too many stanced (yet beefy tires) wagons with specific offsets out there.
Mike
Just a quick calculation of your proposed setup compared to my current 9.5" et28 shows:
F: 19x9.5 et32 (compared to 18x9.5 et28)
- outside of wheel: 4mm more clearance
- inside of wheel: 4mm less clearance (you have room here)
- tires: 255/35 will be fine, but I would roll the front fenders because the corner of the tire CAN grab the inner fender lip when going up a driveway with the wheel articulated at some steering angle--ask me how I know (i.e., it happened to me).
R: 19x10 et35 (compared to 18x9.5 et28)
- outside of wheel: 1mm more clearance
- inside of wheel: 13mm less clearance (you have room here)
- tires: 285 may have a slight rub (on fender) such that you may not even consider fender rolling because it's minor and only happen if you're really low, BUT my observation is based on my sedan rear fender (stock fenders; not rolled).
The following users liked this post:
kevstaarr (09-03-2020)
#89
The fitment will be similar; your setup being slightly less aggressive in front (4mm).
Just a quick calculation of your proposed setup compared to my current 9.5" et28 shows:
F: 19x9.5 et32 (compared to 18x9.5 et28)
R: 19x10 et35 (compared to 18x9.5 et28)
Just a quick calculation of your proposed setup compared to my current 9.5" et28 shows:
F: 19x9.5 et32 (compared to 18x9.5 et28)
- outside of wheel: 4mm more clearance
- inside of wheel: 4mm less clearance (you have room here)
- tires: 255/35 will be fine, but I would roll the front fenders because the corner of the tire CAN grab the inner fender lip when going up a driveway with the wheel articulated at some steering angle--ask me how I know (i.e., it happened to me).
R: 19x10 et35 (compared to 18x9.5 et28)
- outside of wheel: 1mm more clearance
- inside of wheel: 13mm less clearance (you have room here)
- tires: 285 may have a slight rub (on fender) such that you may not even consider fender rolling because it's minor and only happen if you're really low, BUT my observation is based on my sedan rear fender (stock fenders; not rolled).
19x9.5 et34 (255/35-19)
19x10 et38 (285/30-19)
With fender roll (I will be getting the e63 front end so my buddies shop can cut or alter the fenders to make the wheels work or whatever). Let me know what you think master fitment guru!!! Thanks!
Mike
#90
#91
MBWorld Fanatic!
Joined: Jan 2010
Posts: 1,057
Likes: 19
From: SWFL
E55, E320 CDI , CLA250, Jag XJ Supersport
#92
very cool car. those exhaust tips are sick!!! Very few Pewter cars around and especially in the E55, people don't realize how incredible the color looks in person.
The LED stuff in your taillights is very cool. Are you going to add some to the front?
The car is lowered to an extreme but probably looks better in person.
There is a thread on here about the coilover conversion if you have a taste for that one...
Nice thread!
The LED stuff in your taillights is very cool. Are you going to add some to the front?
The car is lowered to an extreme but probably looks better in person.
There is a thread on here about the coilover conversion if you have a taste for that one...
Nice thread!
#93
MBWorld Fanatic!
Joined: Dec 2005
Posts: 6,752
Likes: 92
From: NH
2012 C63 BS & 2014 E63 Estate & 2008 CLK63 BS
very cool car. those exhaust tips are sick!!! Very few Pewter cars around and especially in the E55, people don't realize how incredible the color looks in person.
The LED stuff in your taillights is very cool. Are you going to add some to the front?
The car is lowered to an extreme but probably looks better in person.
There is a thread on here about the coilover conversion if you have a taste for that one...
Nice thread!
The LED stuff in your taillights is very cool. Are you going to add some to the front?
The car is lowered to an extreme but probably looks better in person.
There is a thread on here about the coilover conversion if you have a taste for that one...
Nice thread!
"****ty color car" from one member speaking about my car.
#97
I removed the factory turn signal bulbs, which left a hole and after some minor trimming, was able to snugly fit a standard 7506 bulb base. I used the factory (-) to the bulb base and then used a female spade terminal to connect the (+) contact and solder the other end to the (+) contact of the LED bulb with a short wire.
I my previous experience, these particular LED bulbs (Solarzen) has the most load resistance with its internal resistors to eliminate "Bulb Out" errors. But for some reason, one LED bulb was giving me intermittent errors (likely a QC issue, bad bulb) so I installed an external load resistor for just that bulb. No bulb errors.
Thanks bro!
It did take a while for me to get used to the connected exhaust tips, but they've finally grown on me now!
Actually, I am, currently running LED bulbs for the front turn signals as well. Thanks pare! Your pewter ride is looking clean! Just tryin' to keep it simple and clean pare.
I my previous experience, these particular LED bulbs (Solarzen) has the most load resistance with its internal resistors to eliminate "Bulb Out" errors. But for some reason, one LED bulb was giving me intermittent errors (likely a QC issue, bad bulb) so I installed an external load resistor for just that bulb. No bulb errors.
It did take a while for me to get used to the connected exhaust tips, but they've finally grown on me now!
Actually, I am, currently running LED bulbs for the front turn signals as well. Thanks pare! Your pewter ride is looking clean! Just tryin' to keep it simple and clean pare.
#98
More updates.
Installed a NeedsWing catchcan.
TB shaft grind, FTW.
I went a bit conservative so I can probably grind more off, but not likely a measurable benefit to go through the trouble again, lol.
Road trip status, lol.
Installed a NeedsWing catchcan.
TB shaft grind, FTW.
I went a bit conservative so I can probably grind more off, but not likely a measurable benefit to go through the trouble again, lol.
Road trip status, lol.