The Official C63 AMG Picture Thread (Post your photos here!)




How come you went with a 235/35 series on front (normally 235/40 series).
I'm running a 10mm hub spacer with ET48 on my 18x8.5" (so gives ET38) and I'm going 245/40 next time.
You should be able to fit 275/35 on rear with std suspension even on 10" rim.
I'm running 275 on 18x9" with ET50 so my tire shoulder is similar distance to the fender as yours.
Last edited by Cwagon; Oct 20, 2020 at 04:56 PM.




To check tire clearance I jack up one and then place a block under 1 wheel lower the car down.
The wheel on the block is then pushed up into the wheel well giving you and idea whether a particular size might fit.
I did this with my rears and a 10mm spacer to see if a 9-9.5" ET45 275 would fit.
Although the tire rotated there was only a match stick in it so would go with a 265 if I do go those wheel specs.
I've done a few 1/4 mile runs on an isolated road with a few friends cars, - 2014 Mustang GT, & 2018 Kia Stinger GT, - and by handheld stopwatch ran a best of 12.95 and speedo showing 190 kph so I'm happy with that, plus I beat the Stinger and tied the Mustang GT!
i have c63amg 2008.
Can someone help me with this, i cant find any info on this name plate. Its not in amg private lounge engine builder name list.
The Best of Mercedes & AMG
Yeah, they are the OEM Black Series wheels. I did 12mm rear spacer and 15mm front spacer with stud conversion. Im going to put the car up on the lift this weekend to change the oil and I'll lower the suspension a little bit to get rid of the gap..... we will see how it goes.
Sharing our customer's clean C63 (W204) sitting on our 20" BD-8 wheels.
Check out the full gallery by clicking on the image. Enjoy!
Just send us a PM or you may contact us through the following:
Phone: (818) 362-2300
E-Mail: Info@BlaqueDiamond.com
Visit our website and check us out on Social Media:
Website: www.blaquediamond.com
IG: @BDWheels
FB: /BlaqueDiamondWheels
the after market stuff. PO installed Akrapovic full exhaust w/ carbon tips. Metallic matte wrap over the OEM black pain, stance 19" rims. Not sure the offset until I take them off to look.
I'm still trying to figure out who makes the front CF splitter and the rear CF defuser. I'd like to get them covered on my insurance plan. The only ones I find don't have the air flow cutout above the fins








Congrats, very nice coupe. You can try RW Carbon for the CF fiber parts you are looking for.
https://www.rwcarbon.com/135/3/0/655...-diffuser.html
https://www.rwcarbon.com/135/1/0/244...front-lip.html
Congrats, very nice coupe. You can try RW Carbon for the CF fiber parts you are looking for.
https://www.rwcarbon.com/135/3/0/655...-diffuser.html
https://www.rwcarbon.com/135/1/0/244...front-lip.html
thanks those are bang on!!! in fact those ad photos are of my car

Appreciate all the great members here, interesting builds, cool pictures, posts etc. Definitely going to keep lurking here and see what you all do with your cars in the future!
Appreciate all the great members here, interesting builds, cool pictures, posts etc. Definitely going to keep lurking here and see what you all do with your cars in the future!




It looks in great condition on the outside.
Hope you have better roads than I have here in Sydney Australia.
I had the same wheels on mine but 3 wheels developed cracks on the inner rim.
Changed them out for 18's for a better ride but have now fitted forged w205 C63s 19" wheels.





